/*
* Copyright (c) 2013-2014, ARM Limited and Contributors. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* Redistributions of source code must retain the above copyright notice, this
* list of conditions and the following disclaimer.
*
* Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
*
* Neither the name of ARM nor the names of its contributors may be used
* to endorse or promote products derived from this software without specific
* prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
* LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
#ifndef __PL011_H__
#define __PL011_H__
/* PL011 Registers */
#define UARTDR 0x000
#define UARTRSR 0x004
#define UARTECR 0x004
#define UARTFR 0x018
#define UARTILPR 0x020
#define UARTIBRD 0x024
#define UARTFBRD 0x028
#define UARTLCR_H 0x02C
#define UARTCR 0x030
#define UARTIFLS 0x034
#define UARTIMSC 0x038
#define UARTRIS 0x03C
#define UARTMIS 0x040
#define UARTICR 0x044
#define UARTDMACR 0x048
/* Data status bits */
#define UART_DATA_ERROR_MASK 0x0F00
/* Status reg bits */
#define UART_STATUS_ERROR_MASK 0x0F
/* Flag reg bits */
#define PL011_UARTFR_RI (1 << 8) /* Ring indicator */
#define PL011_UARTFR_TXFE (1 << 7) /* Transmit FIFO empty */
#define PL011_UARTFR_RXFF (1 << 6) /* Receive FIFO full */
#define PL011_UARTFR_TXFF (1 << 5) /* Transmit FIFO full */
#define PL011_UARTFR_RXFE (1 << 4) /* Receive FIFO empty */
#define PL011_UARTFR_BUSY (1 << 3) /* UART busy */
#define PL011_UARTFR_DCD (1 << 2) /* Data carrier detect */
#define PL011_UARTFR_DSR (1 << 1) /* Data set ready */
#define PL011_UARTFR_CTS (1 << 0) /* Clear to send */
/* Control reg bits */
#define PL011_UARTCR_CTSEN (1 << 15) /* CTS hardware flow control enable */
#define PL011_UARTCR_RTSEN (1 << 14) /* RTS hardware flow control enable */
#define PL011_UARTCR_RTS (1 << 11) /* Request to send */
#define PL011_UARTCR_DTR (1 << 10) /* Data transmit ready. */
#define PL011_UARTCR_RXE (1 << 9) /* Receive enable */
#define PL011_UARTCR_TXE (1 << 8) /* Transmit enable */
#define PL011_UARTCR_LBE (1 << 7) /* Loopback enable */
#define PL011_UARTCR_UARTEN (1 << 0) /* UART Enable */
#if !defined(PL011_BASE)
#error "The PL011_BASE macro must be defined."
#endif
#if !defined(PL011_BAUDRATE)
#define PL011_BAUDRATE 115200
#endif
#if !defined(PL011_CLK_IN_HZ)
#define PL011_CLK_IN_HZ 24000000
#endif
#if !defined(PL011_LINE_CONTROL)
/* FIFO Enabled / No Parity / 8 Data bit / One Stop Bit */
#define PL011_LINE_CONTROL (PL011_UARTLCR_H_FEN | PL011_UARTLCR_H_WLEN_8)
#endif
/* Line Control Register Bits */
#define PL011_UARTLCR_H_SPS (1 << 7) /* Stick parity select */
#define PL011_UARTLCR_H_WLEN_8 (3 << 5)
#define PL011_UARTLCR_H_WLEN_7 (2 << 5)
#define PL011_UARTLCR_H_WLEN_6 (1 << 5)
#define PL011_UARTLCR_H_WLEN_5 (0 << 5)
#define PL011_UARTLCR_H_FEN (1 << 4) /* FIFOs Enable */
#define PL011_UARTLCR_H_STP2 (1 << 3) /* Two stop bits select */
#define PL011_UARTLCR_H_EPS (1 << 2) /* Even parity select */
#define PL011_UARTLCR_H_PEN (1 << 1) /* Parity Enable */
#define PL011_UARTLCR_H_BRK (1 << 0) /* Send break */
#endif /* __PL011_H__ */
