diff --git a/dts/Bindings/clock/sunxi-ccu.txt b/dts/Bindings/clock/sunxi-ccu.txt
index e9c5a1d..f465647 100644
--- a/dts/Bindings/clock/sunxi-ccu.txt
+++ b/dts/Bindings/clock/sunxi-ccu.txt
@@ -22,7 +22,8 @@
 - #clock-cells : must contain 1
 - #reset-cells : must contain 1
 
-For the PRCM CCUs on H3/A64, one more clock is needed:
+For the PRCM CCUs on H3/A64, two more clocks are needed:
+- "pll-periph": the SoC's peripheral PLL from the main CCU
 - "iosc": the SoC's internal frequency oscillator
 
 Example for generic CCU:
@@ -39,8 +40,8 @@
 r_ccu: clock@01f01400 {
 	compatible = "allwinner,sun50i-a64-r-ccu";
 	reg = <0x01f01400 0x100>;
-	clocks = <&osc24M>, <&osc32k>, <&iosc>;
-	clock-names = "hosc", "losc", "iosc";
+	clocks = <&osc24M>, <&osc32k>, <&iosc>, <&ccu CLK_PLL_PERIPH0>;
+	clock-names = "hosc", "losc", "iosc", "pll-periph";
 	#clock-cells = <1>;
 	#reset-cells = <1>;
 };
diff --git a/dts/Bindings/gpio/gpio-mvebu.txt b/dts/Bindings/gpio/gpio-mvebu.txt
index 42c3bb2..01e331a 100644
--- a/dts/Bindings/gpio/gpio-mvebu.txt
+++ b/dts/Bindings/gpio/gpio-mvebu.txt
@@ -41,9 +41,9 @@
 Optional properties:
 
 In order to use the GPIO lines in PWM mode, some additional optional
-properties are required. Only Armada 370 and XP support these properties.
+properties are required.
 
-- compatible: Must contain "marvell,armada-370-xp-gpio"
+- compatible: Must contain "marvell,armada-370-gpio"
 
 - reg: an additional register set is needed, for the GPIO Blink
   Counter on/off registers.
@@ -71,7 +71,7 @@
 		};
 
 		gpio1: gpio@18140 {
-			compatible = "marvell,armada-370-xp-gpio";
+			compatible = "marvell,armada-370-gpio";
 			reg = <0x18140 0x40>, <0x181c8 0x08>;
 			reg-names = "gpio", "pwm";
 			ngpios = <17>;
diff --git a/dts/Bindings/mfd/stm32-timers.txt b/dts/Bindings/mfd/stm32-timers.txt
index bbd083f..1db6e00 100644
--- a/dts/Bindings/mfd/stm32-timers.txt
+++ b/dts/Bindings/mfd/stm32-timers.txt
@@ -31,7 +31,7 @@
 		compatible = "st,stm32-timers";
 		reg = <0x40010000 0x400>;
 		clocks = <&rcc 0 160>;
-		clock-names = "clk_int";
+		clock-names = "int";
 
 		pwm {
 			compatible = "st,stm32-pwm";
diff --git a/dts/Bindings/net/dsa/b53.txt b/dts/Bindings/net/dsa/b53.txt
index d6c6e41..8ec2ca2 100644
--- a/dts/Bindings/net/dsa/b53.txt
+++ b/dts/Bindings/net/dsa/b53.txt
@@ -34,7 +34,7 @@
       "brcm,bcm6328-switch"
       "brcm,bcm6368-switch" and the mandatory "brcm,bcm63xx-switch"
 
-See Documentation/devicetree/bindings/dsa/dsa.txt for a list of additional
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
 required and optional properties.
 
 Examples:
diff --git a/dts/Bindings/net/smsc911x.txt b/dts/Bindings/net/smsc911x.txt
index 16c3a95..acfafc8 100644
--- a/dts/Bindings/net/smsc911x.txt
+++ b/dts/Bindings/net/smsc911x.txt
@@ -27,6 +27,7 @@
   of the device. On many systems this is wired high so the device goes
   out of reset at power-on, but if it is under program control, this
   optional GPIO can wake up in response to it.
+- vdd33a-supply, vddvario-supply : 3.3V analog and IO logic power supplies
 
 Examples:
 
diff --git a/dts/include/dt-bindings/clock/sun50i-a64-ccu.h b/dts/include/dt-bindings/clock/sun50i-a64-ccu.h
index 370c0a0..d66432c 100644
--- a/dts/include/dt-bindings/clock/sun50i-a64-ccu.h
+++ b/dts/include/dt-bindings/clock/sun50i-a64-ccu.h
@@ -43,6 +43,8 @@
 #ifndef _DT_BINDINGS_CLK_SUN50I_A64_H_
 #define _DT_BINDINGS_CLK_SUN50I_A64_H_
 
+#define CLK_PLL_PERIPH0		11
+
 #define CLK_BUS_MIPI_DSI	28
 #define CLK_BUS_CE		29
 #define CLK_BUS_DMA		30
diff --git a/dts/include/dt-bindings/clock/sun8i-h3-ccu.h b/dts/include/dt-bindings/clock/sun8i-h3-ccu.h
index c2afc41..e139fe5 100644
--- a/dts/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ b/dts/include/dt-bindings/clock/sun8i-h3-ccu.h
@@ -43,6 +43,8 @@
 #ifndef _DT_BINDINGS_CLK_SUN8I_H3_H_
 #define _DT_BINDINGS_CLK_SUN8I_H3_H_
 
+#define CLK_PLL_PERIPH0		9
+
 #define CLK_CPUX		14
 
 #define CLK_BUS_CE		20