This patch changes the type of the base address parameter in the
ARM device driver APIs to uintptr_t (GIC, CCI, TZC400, PL011). The
uintptr_t type allows coverage of the whole memory space and to
perform arithmetic operations on the addresses. ARM platform code
has also been updated to use uintptr_t as GIC base address in the
configuration.

Fixes ARM-software/tf-issues#214

Change-Id: I1b87daedadcc8b63e8f113477979675e07d788f1

The ARM GIC driver treats the entire contents of the GICC_HPPIR as the interrupt
ID instead of just bits[9:0]. This could result in an SGI being treated as a
Group 1 interrupt on a GICv2 system.

This patch introduces a mask to retrieve only the ID from a read of GICC_HPPIR,
GICC_IAR and similar registers. The value read from these registers is masked
with this constant prior to use as an interrupt ID.

Fixes ARM-software/tf-issues#306

Change-Id: Ie3885157de33b71df9781a41f6ef015a30c4608d

On a GICv2 system, the group status of PPIs and SGIs is set in the GICD_IGROUPR0
register. On a GICv3 system, if affinity routing is enabled for the non-secure
state, then the group status of PPIs and SGIs should be set in the GICR_IGROUPR0
register. ARM Trusted firmware sets the group status using the GICv2
sequence. On a GICv3 system, if the group status of an interrupt is set to Group
1 through a write to the GICD_IGROUPR0, then the GICR_IGROUPR0 is updated as
well.

The current sequence is incorrect since it first marks all PPIs and SGIs as
Group 1. It then clears the bits in GICD_IGROUPR0 corresponding to secure
interrupts to set their group status to Group 0. This operation is a no-op. It
leaves the secure generic timer interrupt (#29) used by the TSP marked as Group
1. This causes the interrupt to interfere with the execution of non-secure
software. Once an interrupt has been marked as Group 1, the GICR_IGROUPR0 should
be programmed to change its group status.

This patch rectifies this issue by setting the group status of only the
non-secure PPI and SGIs to Group 1 in the first place. GICD_IGROUPR0 resets to
0. So secure interrupts are marked as Group 0 by default.

Change-Id: I958b4b15f3e2b2444ce4c17764def36216498d00

This patch introduces several improvements to the ARM GIC driver:

* In function gicd_set_itargetsr(), target CPU is specified using
  the same bit mask detailed in the GICD_ITARGETSRn register instead
  of the CPU linear ID, removing the dependency between bit position
  and linear ID in the platform porting. The current CPU bit mask
  may be obtained by reading GICD_ITARGETSR0.

* PPIs and SGIs are initialized in arm_gic_pcpu_distif_setup().
  SPIs are initialized in arm_gic_distif_setup().

* By default, non secure interrupts are assigned the maximum
  priority allowed to a non secure interrupt (defined by
  GIC_HIGHEST_NS_PRIORITY).

* GICR base address is allowed to be NULL for GICv1 and GICv2.

Change-Id: Ie2837fe860d43b2282e582dfdb13c39c6186f232

Assert a valid security state using the macro sec_state_is_valid().
Replace assert() with panic() in those cases that might arise
because of runtime errors and not programming errors.
Replace panic() with assert() in those cases that might arise
because of programming errors.

Fixes ARM-software/tf-issues#96

Change-Id: I51e9ef0439fd5ff5e0edfef49050b69804bf14d5

Refactor the FVP gic code in plat/fvp/fvp_gic.c to be a generic ARM
GIC driver in drivers/arm/gic/arm_gic.c. Provide the platform
specific inputs in the arm_gic_setup() function so that the driver
has no explicit dependency on platform code.

Provide weak implementations of the platform interrupt controller
API in a new file, plat/common/plat_gic.c. These simply call through
to the ARM GIC driver.

Move the only remaining FVP GIC function, fvp_gic_init() to
plat/fvp/aarch64/fvp_common.c and remove plat/fvp/fvp_gic.c

Fixes ARM-software/tf-issues#182

Change-Id: Iea82fe095fad62dd33ba9efbddd48c57717edd21