The only difference between GIC-500 and GIC-600 relevant to TF-A is the
differing power management sequence.
A certain GIC implementation is detectable at runtime, for instance by
checking the IIDR register. Let's add that test before initiating the
GIC-600 specific sequence, so the code can be used on both GIC-600 and
GIC-500 chips alike, without deciding on a GIC chip at compile time.

This means that the GIC-500 "driver" is now redundant. To allow minimal
platform support, add a switch to disable GIC-600 support.

Change-Id: I17ea97d9fb05874772ebaa13e6678b4ba3415557
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

This patch moves all GICv3 driver files into new added
'gicv3.mk' makefile for the benefit of the generic driver
which can evolve in the future without affecting platforms.
The patch adds GICv3 driver configuration flags
'GICV3_IMPL', 'GICV3_IMPL_GIC600_MULTICHIP' and
'GICV3_OVERRIDE_DISTIF_PWR_OPS' described in
'GICv3 driver options' section of 'build-option.rst'
document.

NOTE: Platforms with GICv3 driver need to be modified to
include 'drivers/arm/gic/v3/gicv3.mk' in their makefiles.

Change-Id: If055f6770ff20f5dee5a3c99ae7ced7cdcac5c44
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

This patch provides separation of GICD, GICR accessor
functions and adds new macros for GICv3 registers access
as a preparation for GICv3.1 and GICv4 support.
NOTE: Platforms need to modify to include both
'gicdv3_helpers.c' and 'gicrv3_helpers.c' instead of the
single helper file previously.

Change-Id: I1641bd6d217d6eb7d1228be3c4177b2d556da60a
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

As on SGI platforms, SCPI is unsupported on SGM platforms.

Change-Id: I556ed095b9eb55b72447230ee2725d3c76160a08
Signed-off-by: Chris Kay <chris.kay@arm.com>

The BL1 stage setup code for ARM platforms sets up the SP805 watchdog
controller as the secure watchdog. But not all ARM platforms use SP805
as the secure watchdog controller.

So introduce two new ARM platform code specific wrapper functions to
start and stop the secure watchdog. These functions then replace the
calls to SP805 driver in common BL1 setup code. All the ARM platforms
implement these wrapper functions by either calling into SP805 driver
or the SBSA watchdog driver.

Change-Id: I1a9a11b124cf3fac2a84f22ca40acd440a441257
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

The weak version of plat_get_mbedtls_heap() was being used.

Change-Id: I6da331a098dd1af5bb64729d5b914cfb74b8869e
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>

The top level makefile defines the PLAT variable, not PLATFORM.
This mistake was causing an empty variable expansion and showing an
incomplete error message.

Change-Id: I5da1275c73c61a7c1823643a76300f255841719d
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>

This lets any future CSS platforms to use RESET_TO_BL31 flag.

Change-Id: I32a90fce43cb0c6f4d33589653a0fd6a7ecc9577
Signed-off-by: Deepak Pandey <Deepak.Pandey@arm.com>

- Remove references to removed build options.
- Remove support for LOAD_IMAGE_V2=0.

Change-Id: I296385ef2ebf829446c76a54400d73f963ed265f
Tested-by: Nariman Poushin <nariman.poushin@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Add support for System Guidance for Mobile platform SGM775

Change-Id: I2442a50caae8f597e5e5949cd48f695cf75d9653
Signed-off-by: Nariman Poushin <nariman.poushin@linaro.org>