Merge pull request #1505 from Yann-lms/mmc_delays ...

mmc: add required delays when retrying commands

Merge pull request #1501 from robertovargas-arm/cci ...

cci: Wait before reading status register

mmc: add required delays when retrying commands ...

A new function mmc_reset_to_idle is also created.

Signed-off-by: Yann Gautier <yann.gautier@st.com>

Merge pull request #1498 from glneo/cache-early-fixes ...

Early cache enable and coherency fixes

Fix MISRA defects in SP805 driver ...

Fix violations of MISRA C-2012 Rules 10.1, 10.3 and 10.4.

Change-Id: I13c6acda798c1666892f630f097a23e68748f9e4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

GIC: Do not flush cache when unneeded ...

When a platform enables its caches before it initializes the
GICC/GICR interface then explicit cache maintenance is not
needed. Remove these here.

Signed-off-by: Andrew F. Davis <afd@ti.com>

stm32mp1: Add DDR support and its security with TZC400 ...

The DDR driver is under dual license, BSD and GPLv2.
The configuration parameters are taken from device tree.

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

stm32mp1: Add PMIC support ...

If a PMIC companion chip is present on board, it has to be configured
for regulators supplies.
This check is done with board DT configuration.

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Pascal Paillet <p.paillet@st.com>

stm32mp1: Add console support ...

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

stm32mp1: Add GPIO support ...

The management of pinctrl nodes of device tree is also added.

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>

stm32mp1: Add clock and reset support ...

The clock driver is under dual license, BSD and GPLv2.
The clock driver uses device tree, so a minimal support for this is added.
The required files for driver and DTS files are in include/dt-bindings/.

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

Introduce STMicroelectronics STM32MP1 platform ...

STM32MP1 is a microprocessor designed by STMicroelectronics,
based on a dual Arm Cortex-A7.
It is an Armv7-A platform, using dedicated code from TF-A.

STM32MP1 uses BL2 compiled with BL2_AT_EL3.

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Pascal Paillet <p.paillet@st.com>

Merge pull request #1450 from MISL-EBU-System-SW/marvell-support-v6 ...

Marvell support for Armada 8K SoC family

cci: Wait before reading status register ...

The functions cci_enable_snoop_dvm_reqs and cci_disable_snoop_dvm_reqs write
in the SNOOP_CTRL_REGISTER of the slave interface and it polls the status
register to be sure that the operation is finished before leaving the
functions. If the write in SNOOP_CTRL_REGISTER is reordered after the first
read in the status register then these functions can finish before
enabling/disabling snoops and DVM messages.

The CCI500 TRM specifies:

	Wait for the completion of the write to the Snoop Control Register
	before testing the change_pending bit.

Change-Id: Idc7685963f412be1c16bcd3c6e3cca826e2fdf38
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

io: Allow image load to address zero ...

Remove assert on buffer address equal zero.
Marvell uses address 0x0 for loading BL33,
so this check is irrelevant and breaks the
debug builds on Marvell platforms.

Change-Id: Ie56a51138e2e4ddd8986dd7036797dc2d8b10125
Signed-off-by: Haim Boot <hayim@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/54589

marvell: drivers: Add i2c driver ...

Add i2c driver for A8K SoC family.

Change-Id: I5932b2fce286d84fc3ad5a74c4c456001faa3196
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

mvebu: cp110: add COMPHY driver ...

Add COMPHY driver for usage in a runtime service.

Change-Id: I6fb42d0a099496d5699ee24684ae2b93ed35770b
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

marvell: drivers: Add thermal driver ...

Add thermal driver for A8K SoC family.
The termal unit data is used by Marvell DRAM initialization
code for optimizing the memory controller configuration

Change-Id: Iad92689fa6e4224a89d872e9aa015393abd9cf73
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

marvell: drivers: Add L3/system cache management drivers ...

Add LLC (L3) cache management drivers for Marvell SoCs
AP806, AP807 and AP810

Change-Id: Ic70710f9bc5b6b48395d62212df7011e2fbb5894
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

marvell: drivers: Add MoChi drivers ...

Add ModularChip and MCI drivers for A8K SoC family.
ModularChip drivers include support for the internal building
blocks of Marvell ARMADA SoCs - APN806, APN807 and CP110

Change-Id: I9559343788fa2e5eb47e6384a4a7d47408787c02
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

marvell: drivers: Add address decoding units drivers ...

Add address decoding unit drivers for Marvell SoCs.

Address decoding flow and address translation units chart
are located at docs/marvell/misc/mvebu-a8k-addr-map.txt

Change-Id: Id6ce311fa1f4f112df3adfac5d20449f495f71ed
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Merge pull request #1432 from Yann-lms/mmc_framework ...

[RFC] Add MMC framework

Add MMC framework ...

This change is largely based on existing eMMC framework by Haojian Zhuang
(@hzhuang1).

The MMC framework supports both eMMC and SD card devices. It was
written as a new framework since breaking few eMMC framework APIs.

At card probe and after the reset to idle command (CMD0), a Send
Interface Condition Command is sent (CMD8) to distinguish between
eMMC and SD card devices. eMMC devices go through the same
sequence as in the former eMMC framework. Else the framework
uses commands dedicated to SD-cards for init or frequency switch.

A structure is created to share info with the driver. It stores:
- the MMC type (eMMC, SD or SD HC)
- the device size
- the max frequency supported by the device
- the block size: 512 for eMMC and SD-HC and read from CSD
 structure for older SD-cards

Restriction to align buffers on block size has been removed.
Cache maintenance was removed and is expected to be done in the platform
or device driver.

The MMC framework includes some MISRA compliance coding style
maybe not yet ported in the existing eMMC framework.

Fixes ARM-software/tf-issues#597

Signed-off-by: Yann Gautier <yann.gautier@st.com>

Extend FIP io driver to support multiple FIP devices ...

Platform can define MAX_NUM_FIP_DEVICES in platform_def.h
to define the number of FIP io devices.

The FIP driver doesn't support muliple open file.
So only one single file can be open at a time across
multiple FIP devices.

For any FIP device, an image should be loaded
fully before moving on to the next image.

Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>

Merge pull request #1406 from robertovargas-arm/uuid ...

Make TF UUID RFC 4122 compliant

Move to mbedtls-2.10.0 tag ...

To build with the new release, we pick couple of more files from mbedTLS
library.

Change-Id: I77dfe5723284cb26d4e5c717fb0e6f6dd803cb6b
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Make TF UUID RFC 4122 compliant ...

RFC4122 defines that fields are stored in network order (big endian),
but TF-A stores them in machine order (little endian by default in TF-A).
We cannot change the future UUIDs that are already generated, but we can store
all the bytes using arrays and modify fiptool to generate the UUIDs with
the correct byte order.

Change-Id: I97be2d3168d91f4dee7ccfafc533ea55ff33e46f
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Merge pull request #1402 from glneo/for-upstream-uart ...

drivers: ti: uart: Add TI specific 16550 initialization

Fix MISRA Rule 5.3 Part 2 ...

Use a _ prefix for Macro arguments to prevent that argument from
hiding variables of the same name in the outer scope

Rule 5.3: An identifier declared in an inner scope shall not
          hide an identifier declared in an outer scope

Fixed For:
    make LOG_LEVEL=50 PLAT=fvp

Change-Id: I67b6b05cbad4aeca65ce52981b4679b340604708
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

Fix MISRA Rule 5.1 ...

Rule 5.1: External identifiers shall be distinct

Some of the identifier names in the GICv3 driver were so long that the
first 31 characters were identical. This patch shortens these names to
make sure they are different.

Fixed for:
    LOG_LEVEL=50 PLAT=fvp

Change-Id: Iecd551e3a015d144716b87b42c83dd3ab8c34d90
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>