- Remove support for LOAD_IMAGE_V2=0.
- Replace deprecated bl1_init_bl2_mem_layout().
- Migrate to bl2_early_platform_setup2().
- Migrate to bl31_early_platform_setup2().
- Use PLAT_VIRT_ADDR_SPACE_SIZE and PLAT_PHY_ADDR_SPACE_SIZE.
- Remove references to removed build options.
- Update Makefile paths.

Change-Id: I52e02633365b3db4244f7ff0f99a6446eae619f0
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Migrate from emmc framework to mmc framework.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

Also change header guards to fix defects of MISRA C-2012 Rule 21.1.

Change-Id: Ied0d4b0e557ef6119ab669d106d2ac5d99620c57
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

MISRA C-2012 Rule 7.3 violation: lowercase l shall not be used as literal suffixes.

This patch resolves this for the ULL() macro by using ULL suffix instead
of the ull suffix.

Change-Id: Ia8183c399e74677e676956e8653e82375d0e0a01
Signed-off-by: David Cunado <david.cunado@arm.com>

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>

Let bl1 and bl2 have the ability to load images from emmc instead of
dram (mmap).

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>

The security properties of some IP blocks are configured to secure mode
after reset. This means these IP blocks can only be accessed by cpus
in secure state by default. These should be configured correclty as needed.

Signed-off-by: y00241285 <yyangwei.yangwei@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>

This is currently the maximum allowed without affecting bootup.

Signed-off-by: Victor Chong <victor.chong@linaro.org>

to PLAT_POPLAR_NS_IMAGE_OFFSET

Signed-off-by: Victor Chong <victor.chong@linaro.org>

Per
https://github.com/sdrobertw/Poplar/blob/master/HardwareDocs/Processor_Datasheet_v2XX.pdf
there are 13 groups of GPIO controllers, not 12.

Signed-off-by: Victor Chong <victor.chong@linaro.org>

Change-Id: Ibca6ea29be32783de666e0e0a0481668fc11860f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

The board features the Hi3798C V200 with an integrated quad-core
64-bit ARM Cortex A53 processor and high performance Mali T720 GPU,
making it capable of running any commercial set-top solution based on
Linux or Android. Its high performance specification also supports a
premium user experience with up to H.265 HEVC decoding of 4K video at
60 frames per second.

SOC  Hisilicon Hi3798CV200
CPU  Quad-core ARM Cortex-A53 64 bit
DRAM DDR3/3L/4 SDRAM interface, maximum 32-bit data width 2 GB
USB  Two USB 2.0 ports One USB 3.0 ports
CONSOLE  USB-micro port for console support
ETHERNET  1 GBe Ethernet
PCIE  One PCIe 2.0 interfaces
JTAG  8-Pin JTAG
EXPANSION INTERFACE  Linaro 96Boards Low Speed Expansion slot
DIMENSION Standard 160×120 mm 96Boards Enterprice Edition form factor
WIFI  802.11AC 2*2 with Bluetooth
CONNECTORS  One connector for Smart Card One connector for TSI

The platform boot sequence is as follows:
    l-loader --> arm_trusted_firmware --> u-boot

Repositories:
 - https://github.com/Linaro/poplar-l-loader.git
 - https://github.com/Linaro/poplar-u-boot.git

U-Boot is also upstream in the project's master branch.

Make sure you are using the correct branch on each one of these
repositories. The definition of "correct" might change over time (at
this moment in time this would be the "latest" branch).

Build Line:
make CROSS_COMPILE=aarch64-linux-gnu-  all fip SPD=none DEBUG=1
PLAT=poplar BL33=/path/to/u-boot.bin

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Tested-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Alex Elder <elder@linaro.org>