GIC: Introduce API to get interrupt ID ...

Acknowledging interrupt shall return a raw value from the interrupt
controller in which the actual interrupt ID may be encoded. Add a
platform API to extract the actual interrupt ID from the raw value
obtained from interrupt controller.

Document the new function. Also clarify the semantics of interrupt
acknowledge.

Change-Id: I818dad7be47661658b16f9807877d259eb127405
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

SPM: Introduce Secure Partition Manager ...

A Secure Partition is a software execution environment instantiated in
S-EL0 that can be used to implement simple management and security
services. Since S-EL0 is an unprivileged exception level, a Secure
Partition relies on privileged firmware e.g. ARM Trusted Firmware to be
granted access to system and processor resources. Essentially, it is a
software sandbox that runs under the control of privileged software in
the Secure World and accesses the following system resources:

- Memory and device regions in the system address map.
- PE system registers.
- A range of asynchronous exceptions e.g. interrupts.
- A range of synchronous exceptions e.g. SMC function identifiers.

A Secure Partition enables privileged firmware to implement only the
absolutely essential secure services in EL3 and instantiate the rest in
a partition. Since the partition executes in S-EL0, its implementation
cannot be overly complex.

The component in ARM Trusted Firmware responsible for managing a Secure
Partition is called the Secure Partition Manager (SPM). The SPM is
responsible for the following:

- Validating and allocating resources requested by a Secure Partition.
- Implementing a well defined interface that is used for initialising a
  Secure Partition.
- Implementing a well defined interface that is used by the normal world
  and other secure services for accessing the services exported by a
  Secure Partition.
- Implementing a well defined interface that is used by a Secure
  Partition to fulfil service requests.
- Instantiating the software execution environment required by a Secure
  Partition to fulfil a service request.

Change-Id: I6f7862d6bba8732db5b73f54e789d717a35e802f
Co-authored-by: Douglas Raillard <douglas.raillard@arm.com>
Co-authored-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
Co-authored-by: Achin Gupta <achin.gupta@arm.com>
Co-authored-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Add platform hooks for boot redundancy support ...

These hooks are intended to allow one platform to try load
images from alternative places. There is a hook to initialize
the sequence of boot locations and a hook to pass to the next
sequence.

Change-Id: Ia0f84c415208dc4fa4f9d060d58476db23efa5b2
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

GIC: Add API to set priority mask ...

API documentation updated.

Change-Id: I40feec1fe67a960d035061b54dd55610bc34ce1d
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

GIC: Add API to set/clear interrupt pending ...

API documentation updated.

Change-Id: I14e33cfc7dfa93257c82d76fae186b17a1b6d266
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

GIC: Add API to set interrupt routing ...

SPIs can be routed to either a specific PE, or to any one of all
available PEs.

API documentation updated.

Change-Id: I28675f634568aaf4ea1aa8aa7ebf25b419a963ed
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

GIC: Add API to raise secure SGI ...

API documentation updated.

Change-Id: I129725059299af6cc612bafa8d74817f779d7c4f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

GIC: Add APIs to set interrupt type and query support ...

The back end GIC driver converts and assigns the interrupt type to
suitable group.

For GICv2, a build option GICV2_G0_FOR_EL3 is introduced, which
determines to which type Group 0 interrupts maps to.

 - When the build option is set 0 (the default), Group 0 interrupts are
   meant for Secure EL1. This is presently the case.

 - Otherwise, Group 0 interrupts are meant for EL3. This means the SPD
   will have to synchronously hand over the interrupt to Secure EL1.

The query API allows the platform to query whether the platform supports
interrupts of a given type.

API documentation updated.

Change-Id: I60fdb4053ffe0bd006b3b20914914ebd311fc858
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

GIC: Add API to set interrupt priority ...

API documentation updated.

Change-Id: Ib700eb1b8ca65503aeed0ac4ce0e7b934df67ff9
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

GIC: Add APIs to enable and disable interrupt ...

API documentation updated.

Change-Id: Ice7511f8df5356851001d2f7dc2a46cfe318f9ba
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

GIC: Add API to get interrupt active status ...

API documentation updated.

Change-Id: I6d61785af0d5330930c709de971a904dc7c3516c
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

GIC: Add APIs to query interrupt types ...

These APIs allow the GIC implementation to categorize interrupt numbers
into SPIs, PPIs, and SGIs. The default implementations for GICv2 and
GICv3 follows interrupt numbering as specified by the ARM GIC
architecture.

API documentation updated.

Change-Id: Ia6aa379dc955994333232e6138f259535d4fa087
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

GIC: Add API to get running priority ...

Document the API in separate platform interrupt controller API document.

Change-Id: If18f208e10a8a243f5c59d226fcf48e985941949
Co-authored-by: Yousuf A <yousuf.sait@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Implement log framework ...

This patch gives users control over logging messages printed from the C
code using the LOG macros defined in debug.h Users now have the ability
to reduce the log_level at run time using the tf_log_set_max_level()
function. The default prefix string can be defined by platform by
overriding the `plat_log_get_prefix()` platform API which is also
introduced in this patch.

The new log framework results in saving of some RO data. For example,
when BL1 is built for FVP with LOG_LEVEL=LOG_LEVEL_VERBOSE, resulted
in saving 384 bytes of RO data and increase of 8 bytes of RW data. The
framework also adds about 108 bytes of code to the release build of FVP.

Fixes ARM-software/tf-issues#462

Change-Id: I476013d9c3deedfdd4c8b0b0f125665ba6250554
Co-authored-by: Eleanor Bonnici <Eleanor.bonnici@arm.com>
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Use SPDX license identifiers ...

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/

Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Merge pull request #885 from antonio-nino-diaz-arm/an/console-flush ...

Implement console_flush()

Add support for GCC stack protection ...

Introduce new build option ENABLE_STACK_PROTECTOR. It enables
compilation of all BL images with one of the GCC -fstack-protector-*
options.

A new platform function plat_get_stack_protector_canary() is introduced.
It returns a value that is used to initialize the canary for stack
corruption detection. Returning a random value will prevent an attacker
from predicting the value and greatly increase the effectiveness of the
protection.

A message is printed at the ERROR level when a stack corruption is
detected.

To be effective, the global data must be stored at an address
lower than the base of the stacks. Failure to do so would allow an
attacker to overwrite the canary as part of an attack which would void
the protection.

FVP implementation of plat_get_stack_protector_canary is weak as
there is no real source of entropy on the FVP. It therefore relies on a
timer's value, which could be predictable.

Change-Id: Icaaee96392733b721fa7c86a81d03660d3c1bc06
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

Add and use plat_crash_console_flush() API ...

This API makes sure that all the characters sent to the crash console
are output before returning from it.

Porting guide updated.

Change-Id: I1785f970a40f6aacfbe592b6a911b1f249bb2735
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

PSCI: Decouple PSCI stat residency calculation from PMF ...

This patch introduces the following three platform interfaces:

* void plat_psci_stat_accounting_start(const psci_power_state_t *state_info)

  This is an optional hook that platforms can implement in order
  to perform accounting before entering a low power state.  This
  typically involves capturing a timestamp.

* void plat_psci_stat_accounting_stop(const psci_power_state_t *state_info)

  This is an optional hook that platforms can implement in order
  to perform accounting after exiting from a low power state.  This
  typically involves capturing a timestamp.

* u_register_t plat_psci_stat_get_residency(unsigned int lvl,
	const psci_power_state_t *state_info,
	unsigned int last_cpu_index)

  This is an optional hook that platforms can implement in order
  to calculate the PSCI stat residency.

If any of these interfaces are overridden by the platform, it is
recommended that all of them are.

By default `ENABLE_PSCI_STAT` is disabled.  If `ENABLE_PSCI_STAT`
is set but `ENABLE_PMF` is not set then an alternative PSCI stat
collection backend must be provided.  If both are set, then default
weak definitions of these functions are provided, using PMF to
calculate the residency.

NOTE: Previously, platforms did not have to explicitly set
`ENABLE_PMF` since this was automatically done by the top-level
Makefile.

Change-Id: I17b47804dea68c77bc284df15ee1ccd66bc4b79b
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

tbbr: Fix updating of Non-Trusted NV counter ...

The previous code required that a certificate be signed with the ROT
key before the platform's NV counter could be updated with the value
in the certificate.  This implies that the Non-Trusted NV counter was
not being updated for Non-Trusted content certificates, as they cannot
be signed with the ROT key in the TBBR CoT scheme.

The code is reworked to only allow updating the platform's Trusted NV
counter when a certificate protected by the Trusted NV counter is
signed with the ROT key.

Content certificates protected by the Non-Trusted NV counter are
allowed to update the platform's Non-Trusted NV counter, assuming
that the certificate value is higher than the platform's value.

A new optional platform API has been introduced, named
plat_set_nv_ctr2().  Platforms may choose to implement it and perform
additional checks based on the authentication image descriptor before
modifying the NV counters.  A default weak implementation is available
that just calls into plat_set_nv_ctr().

Fixes ARM-software/tf-issues#426

Change-Id: I4fc978fd28a3007bc0cef972ff1f69ad0413b79c
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

AArch32: Common changes needed for BL1/BL2 ...

This patch adds common changes to support AArch32 state in
BL1 and BL2. Following are the changes:

* Added functions for disabling MMU from Secure state.
* Added AArch32 specific SMC function.
* Added semihosting support.
* Added reporting of unhandled exceptions.
* Added uniprocessor stack support.
* Added `el3_entrypoint_common` macro that can be
  shared by BL1 and BL32 (SP_MIN) BL stages. The
  `el3_entrypoint_common` is similar to the AArch64
  counterpart with the main difference in the assembly
  instructions and the registers that are relevant to
  AArch32 execution state.
* Enabled `LOAD_IMAGE_V2` flag in Makefile for
  `ARCH=aarch32` and added check to make sure that
  platform has not overridden to disable it.

Change-Id: I33c6d8dfefb2e5d142fdfd06a0f4a7332962e1a3

Add new version of image loading. ...

This patch adds capability to load BL images based on image
descriptors instead of hard coded way of loading BL images.
This framework is designed such that it can be readily adapted
by any BL stage that needs to load images.

In order to provide the above capability the following new
platform functions are introduced:

  bl_load_info_t *plat_get_bl_image_load_info(void);
    This function returns pointer to the list of images that the
    platform has populated to load.

  bl_params_t *plat_get_next_bl_params(void);
    This function returns a pointer to the shared memory that the
    platform has kept aside to pass trusted firmware related
    information that next BL image needs.

  void plat_flush_next_bl_params(void);
    This function flushes to main memory all the params that
    are passed to next image.

  int bl2_plat_handle_post_image_load(unsigned int image_id)
    This function can be used by the platforms to update/use
    image information for given `image_id`.

`desc_image_load.c` contains utility functions which can be used
by the platforms to generate, load and executable, image list
based on the registered image descriptors.

This patch also adds new version of `load_image/load_auth_image`
functions in-order to achieve the above capability.

Following are the changes for the new version as compared to old:
  - Refactor the signature and only keep image_id and image_info_t
    arguments. Removed image_base argument as it is already passed
    through image_info_t. Given that the BL image base addresses and
    limit/size are already provided by the platforms, the meminfo_t
    and entry_point_info arguments are not needed to provide/reserve
    the extent of free memory for the given BL image.

  - Added check for the image size against the defined max size.
    This is needed because the image size could come from an
    unauthenticated source (e.g. the FIP header).
    To make this check, new member is added to the image_info_t
    struct for identifying the image maximum size.

New flag `LOAD_IMAGE_V2` is added in the Makefile.
Default value is 0.

NOTE: `TRUSTED_BOARD_BOOT` is currently not supported when
      `LOAD_IMAGE_V2` is enabled.

Change-Id: Ia7b643f4817a170d5a2fbf479b9bc12e63112e79

Rework type usage in Trusted Firmware ...

This patch reworks type usage in generic code, drivers and ARM platform files
to make it more portable. The major changes done with respect to
type usage are as listed below:

* Use uintptr_t for storing address instead of uint64_t or unsigned long.
* Review usage of unsigned long as it can no longer be assumed to be 64 bit.
* Use u_register_t for register values whose width varies depending on
  whether AArch64 or AArch32.
* Use generic C types where-ever possible.

In addition to the above changes, this patch also modifies format specifiers
in print invocations so that they are AArch64/AArch32 agnostic. Only files
related to upcoming feature development have been reworked.

Change-Id: I9f8c78347c5a52ba7027ff389791f1dad63ee5f8

Allow dynamic overriding of ROTPK verification ...

A production ROM with TBB enabled must have the ability to boot test software
before a real ROTPK is deployed (e.g. manufacturing mode). Previously the
function plat_get_rotpk_info() must return a valid ROTPK for TBB to succeed.
This patch adds an additional bit `ROTPK_NOT_DEPLOYED` in the output `flags`
parameter from plat_get_rotpk_info(). If this bit is set, then the ROTPK
in certificate is used without verifying against the platform value.

Fixes ARM-software/tf-issues#381

Change-Id: Icbbffab6bff8ed76b72431ee21337f550d8fdbbb

Add 32 bit version of plat_get_syscnt_freq ...

Added plat_get_syscnt_freq2, which is a 32 bit variant of the 64 bit
plat_get_syscnt_freq. The old one has been flagged as deprecated.
Common code has been updated to use this new version. Porting guide
has been updated.

Change-Id: I9e913544926c418970972bfe7d81ee88b4da837e

Move `plat_get_syscnt_freq()` to arm_common.c ...

This patch moves the definition for `plat_get_syscnt_freq()`
from arm_bl31_setup.c to arm_common.c. This could be useful
in case a delay timer needs to be installed based on the
generic timer in other BLs.
This patch also modifies the return type for this function
from `uint64_t` to `unsigned long long` within ARM and other
platform files.

Change-Id: Iccdfa811948e660d4fdcaae60ad1d700e4eda80d

Merge pull request #572 from jcastillo-arm/jc/tbb_nvcounter ...

TBB NVcounter support

Modify return type of plat_get_ns_image_entrypoint() ...

This patch modifies the return type of the platform API
`plat_get_ns_image_entrypoint()` from `unsigned long` to
`uintptr_t` in accordance with the coding guidelines.

Change-Id: Icb4510ca98b706aa4d535fe27e203394184fb4ca

TBB: add non-volatile counter support ...

This patch adds support for non-volatile counter authentication to
the Authentication Module. This method consists of matching the
counter values provided in the certificates with the ones stored
in the platform. If the value from the certificate is lower than
the platform, the boot process is aborted. This mechanism protects
the system against rollback.

The TBBR CoT has been updated to include this method as part of the
authentication process. Two counters are used: one for the trusted
world images and another for the non trusted world images.

** NEW PLATFORM APIs (mandatory when TBB is enabled) **

int plat_get_nv_ctr(void *cookie, unsigned int *nv_ctr);

    This API returns the non-volatile counter value stored
    in the platform. The cookie in the first argument may be
    used to select the counter in case the platform provides
    more than one (i.e. TBSA compliant platforms must provide
    trusted and non-trusted counters). This cookie is specified
    in the CoT.

int plat_set_nv_ctr(void *cookie, unsigned int nv_ctr);

    This API sets a new counter value. The cookie may be
    used to select the counter to be updated.

An implementation of these new APIs for ARM platforms is also
provided. The values are obtained from the Trusted Non-Volatile
Counters peripheral. The cookie is used to pass the extension OID.
This OID may be interpreted by the platform to know which counter
must return. On Juno, The trusted and non-trusted counter values
have been tied to 31 and 223, respectively, and cannot be modified.

** IMPORTANT **

THIS PATCH BREAKS THE BUILD WHEN TRUSTED_BOARD_BOOT IS ENABLED. THE
NEW PLATFORM APIs INTRODUCED IN THIS PATCH MUST BE IMPLEMENTED IN
ORDER TO SUCCESSFULLY BUILD TF.

Change-Id: Ic943b76b25f2a37f490eaaab6d87b4a8b3cbc89a

Remove all non-configurable dead loops ...

Added a new platform porting function plat_panic_handler, to allow
platforms to handle unexpected error situations. It must be
implemented in assembly as it may be called before the C environment
is initialized. A default implementation is provided, which simply
spins.

Corrected all dead loops in generic code to call this function
instead. This includes the dead loop that occurs at the end of the
call to panic().

All unnecesary wfis from bl32/tsp/aarch64/tsp_exceptions.S have
been removed.

Change-Id: I67cb85f6112fa8e77bd62f5718efcef4173d8134