Remove MULTI_CONSOLE_API flag and references to it ...

The new API becomes the default one.

Change-Id: Ic1d602da3dff4f4ebbcc158b885295c902a24fec
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>

plat/arm: introduce wrapper functions to setup secure watchdog ...

The BL1 stage setup code for ARM platforms sets up the SP805 watchdog
controller as the secure watchdog. But not all ARM platforms use SP805
as the secure watchdog controller.

So introduce two new ARM platform code specific wrapper functions to
start and stop the secure watchdog. These functions then replace the
calls to SP805 driver in common BL1 setup code. All the ARM platforms
implement these wrapper functions by either calling into SP805 driver
or the SBSA watchdog driver.

Change-Id: I1a9a11b124cf3fac2a84f22ca40acd440a441257
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

plat/arm: Implement ARMv8.3-PAuth interfaces ...

This feature is only supported on FVP.

Change-Id: I4e265610211d92a84bd2773c34acfbe02a1a1826
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

plat/arm: Sanitise includes ...

Use full include paths like it is done for common includes.

This cleanup was started in commit d40e0e08283a ("Sanitise includes
across codebase"), but it only cleaned common files and drivers. This
patch does the same to Arm platforms.

Change-Id: If982e6450bbe84dceb56d464e282bcf5d6d9ab9b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

SPM: Rename SPM_DEPRECATED flag to SPM_MM ...

The SPM implementation based on MM is going to be kept for the
foreseeable future.

Change-Id: I11e96778a4f52a1aa803e7e048d9a7cb24a53954
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>

plat/arm: Restrict PIE support to FVP ...

The patch SHA 55cf015c enabled PIE support when RESET_TO_BL31=1 for
all ARM platforms. But it seems n1sdp platform doesn't work with PIE
support yet. Hence restrict the ENABLE_PIE=1 to fvp platform.

Change-Id: If44e42528e4b0b57c69084503f346576fe0748bd
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

plat/arm: Remove comment that mentions LOAD_IMAGE_V2 ...

This option was removed in v2.0.

Change-Id: I0c929fddb57d60c5eff9e45dd5ee8c636b28e6c3
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

SPM: Load image and RD from SP package ...

Load SP and RD from package instead of relying on RD being already
loaded in memory and the SP being loaded as a BL32 image.

Change-Id: I18d4fbf4597656c6a7e878e1d7c01a8a324f3f8a
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

SPM: Introduce functions to load DTB files ...

Introduce helpers to create resource description struct, as well as code
to load the information from DTB files.

Change-Id: I0f5bb94eb8b01c6cb53fe807a9db0c05a70d7a43
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

plat/arm: Support direct Linux kernel boot in AArch32 ...

This option allows the Trusted Firmware to directly jump to Linux
kernel for aarch32 without the need of an intermediate loader such
as U-Boot.

Similar to AArch64 ARM_LINUX_KERNEL_AS_BL33 only available with
RESET_TO_SP_MIN=1 as well as BL33 and DTB are preloaded in memory.

Change-Id: I908bc1633696be1caad0ce2f099c34215c8e0633
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>

FVP: Enable PIE for RESET_TO_BL31=1 ...

This patch enabled PIE for FVP when RESET_TO_BL31=1. The references
to BL31_BASE are replaced by BL31_START as being a symbol exported by
the linker, will create a dynamic relocation entry in .rela.dyn and
hence will be fixed up by dynamic linker at runtime. Also, we disable
RECLAIM_INIT_CODE when PIE is enabled as the init section overlay
creates some static relocations which cannot be handled by the
dynamic linker currently.

Change-Id: I86df1b0a8b2a8bbbe7c3f3c0b9a08c86c2963ec0
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Merge pull request #1583 from danielboulby-arm/db/AArch32_Multi_Console ...

Enable Multi Console API in AArch32

FVP: Reclaim init code for the stack ...

Map the initialization code for BL31 to overlap with the memory
required for the secondary cores stack. Once BL31 has been
initialized the memory can be remapped to RW data so that it can
be used for secondary cores stacks. By moving code from .text to
.text.init the size of the BL31 image is decreased by a page.

Split arm_common.ld.S into two linker scripts, one for tzc_dram
(arm_tzc_dram.ld.S) and one for reclaiming initialization code
(arm_reclaim_init.ld.S) so that platforms can chose which memory
regions they wish to include.

Change-Id: I648e88f3eda1aa71765744cf34343ecda9320b32
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

plat/arm: Migrate to new interfaces ...

- Remove references to removed build options.
- Remove support for legacy GIC driver.
- Remove support for LOAD_IMAGE_V2=0.

Change-Id: I72f8c05620bdf4a682765e6e53e2c04ca749a3d5
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

plat/arm: Enable MULTI_CONSOLE_API in AArch32 ...

Set MULTI_CONSOLE_API=1 for both AArch64 and AArch32 by default.
MULTI_CONSOLE_API=0 is still supported, but it has to be set from the
command line.

Change-Id: I4eeaa8e243a3fe93ed8a716e502666a26ad28f35
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

ARM platforms: Reintroduce coherent memory for BL1 and BL2 ...

The patch d323af9 removed the support for coherent memory in BL1 and
BL2 for ARM platforms. But the CryptoCell SBROM  integration depends
on use of coherent buffers for passing data from the AP CPU to the
CryptoCell. Hence this patch reintroduces support for coherent
memory in BL1 and BL2 if ARM_CRYPTOCELL_INTEG=1.

Change-Id: I011482dda7f7a3ec9e3e79bfb3f4fa03796f7e02
Signed-Off-by: Soby Mathew <soby.mathew@arm.com>

Create a library file for libfdt ...

TF Makefile was linking all the objects files generated for the
fdt library instead of creating a static library that could be
used in the linking stage.

Change-Id: If3705bba188ec39e1fbf2322a7f2a9a941e1b90d
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

CSS: Use SCMI AP core protocol to set the warm boot entrypoint ...

Change-Id: Iaebbeac1a1d6fbd531e5694b95ed068b7a193e62
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Arm platforms: Remove common RAS configuration source ...

The file arm_ras.c intended to provide common platform-specific RAS
configuration for Arm platforms. Because this file has symbol
definitions, it's proving difficult to provide a common definition.

This patch therefore renames and makes the file specific to FVP. Other
platforms shall provide their own configuration in similar fashion.

Change-Id: I766fd238946e3e49cdb659680e1b45f41b237901
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

plat/arm: Migrate AArch64 port to the multi console driver ...

The old API is deprecated and will eventually be removed.

Arm platforms now use the multi console driver for boot and runtime
consoles. However, the crash console uses the direct console API because
it doesn't need any memory access to work. This makes it more robust
during crashes.

The AArch32 port of the Trusted Firmware doesn't support this new API
yet, so it is only enabled in AArch64 builds. Because of this, the
common code must maintain compatibility with both systems. SP_MIN
doesn't have to be updated because it's only used in AArch32 builds.
The TSP is only used in AArch64, so it only needs to support the new
API without keeping support for the old one.

Special care must be taken because of PSCI_SYSTEM_SUSPEND. In Juno, this
causes the UARTs to reset (except for the one used by the TSP). This
means that they must be unregistered when suspending and re-registered
when resuming. This wasn't a problem with the old driver because it just
restarted the UART, and there were no problems associated with
registering and unregistering consoles.

The size reserved for BL2 has been increased.

Change-Id: Icefd117dd1eb9c498921181a21318c2d2435c441
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

FVP: Enable capability to disable auth via dynamic config ...

This patch adds capability to FVP to disable authentication dynamically
via the `disable_auth` property in TB_FW_CONFIG. Both BL1 and BL2 parses
the TB_FW_CONFIG for the `disable_auth` property and invokes the
`load_dyn_disable_auth()` API to disable authentication if the
property is set to 1. The DYN_DISABLE_AUTH is enabled by default for
FVP as it is a development platform. Note that the TB_FW_CONFIG has to
be authenticated by BL1 irrespective of these settings.

The arm_bl2_dyn_cfg_init() is now earlier in bl2_plat_preload_setup()
rather than in bl2_platform_setup() as we need to get the value of
`disable_auth` property prior to authentication of any image by BL2.

Change-Id: I734acd59572849793e5020ec44c6ac51f654a4d1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Merge pull request #1381 from antonio-nino-diaz-arm/an/kernel-boot ...

plat/arm: Introduce ARM_LINUX_KERNEL_AS_BL33 build option

plat/arm: Introduce ARM_LINUX_KERNEL_AS_BL33 build option ...

Normally, BL33 needs to contain a boot loader like U-Boot or UEFI that
eventually gives control to the OS. However, in some cases, this boot
sequence may be too slow. For example, when doing tests in a
cycle-accurate emulator, the user may only be interested in the
interaction between the Trusted Firmware and the OS, not in the boot
process itself.

The new option ARM_LINUX_KERNEL_AS_BL33 allows BL33 to contain the Linux
kernel image by changing the value of registers x0-x3 to the values
expected by the kernel. This option requires the device tree blob (DTB)
to be present in memory. Its address must be specified in the newly
introduced ARM_PRELOADED_DTB_BASE build option. For now, it only supports
AArch64 kernels.

This option is only available when RESET_TO_BL31=1. For this reason
the BL33 binary must be preloaded in memory and PRELOADED_BL33_BASE must
be used.

For example, if the kernel is loaded at 0x80080000 and the DTB is loaded
at address 0x82000000, the firmware could be built like this:

    CROSS_COMPILE=aarch64-linux-gnu-  \
    make PLAT=fvp DEBUG=1             \
    RESET_TO_BL31=1                   \
    ARM_LINUX_KERNEL_AS_BL33=1        \
    PRELOADED_BL33_BASE=0x80080000    \
    ARM_PRELOADED_DTB_BASE=0x82000000 \
    all fip

Change-Id: If9dc847c65ae2d0c27b51f0fd44fc06b28497db9
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

ARM Platforms: Support RAS ...

- Assign 0x10 for RAS exceptions on ARM platforms, and install
    EHF priority descriptor.

  - Call the common RAS initialisation from ARM BL31 setup.

  - Add empty definitions for platform error records and RAS interrupts.

Change-Id: I0675f299b7840be4c83a9c7a81073a95c605dc90
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Juno: Change the Firmware update detect mechanism ...

Previously, Juno used to depend on the SSC_GPRETN register to inform
about the reset syndrome. This method was removed when SCP migrated
to the SDS framework. But even the SDS framework doesn't report the
reset syndrome correctly and hence Juno failed to enter Firmware
update mode if BL2 authentication failed.

In addition to that, the error code populated in V2M_SYS_NVFLAGS register
does not seem to be retained any more on Juno across resets. This could
be down to the motherboard firmware not doing the necessary to preserve
the value.

Hence this patch modifies the Juno platform to use the same mechanism to
trigger firmware update as FVP which is to corrupt the FIP TOC on
authentication failure. The implementation in `fvp_err.c` is made common
for ARM platforms and is moved to the new `arm_err.c` file in
plat/arm/common folder. The BL1 and BL2 mmap table entries for Juno
are modified to allow write to the Flash memory address.

Change-Id: Ica7d49a3e8a46a90efd4cf340f19fda3b549e945
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

ARM Platforms: Load HW_CONFIG in BL2 ...

The patch adds the necessary changes to load HW_CONFIG in BL2 for
ARM Platforms :

1. The load address of HW_CONFIG is specified via the `hw_config_addr`
property in TB_FW_CONFIG is loaded by BL1. The `hw_config_max_size`
property defines the maximum size to be expected for the HW_CONFIG.
The `arm_dyn_cfg_helpers.c` and corresponding header implements
utility functions to parse these DT properties defined.
The `arm_dyn_cfg.c` implements wrappers to these helpers to enable
them to be invoked from ARM platform layer.

2. `HW_CONFIG` is added to the `bl2_mem_params_descs[]` array which is
the list of images to be loaded by BL2.

3. The `libfdt` sources are now included when BL2 is built

4. A new helper `populate_next_bl_params_config()` is introduced in
desc_image_load.c to populate the subsequent executable BL images
with the `hw_config` and the corresponding `fw_config` if available.
The `plat_get_next_bl_params()` API for ARM platforms is modified to
invoke this new helper.

5. The implementation of `bl2_early_platform_setup2()` is modified to
consider `arg0` as well in addition to `arg1` passed from BL1.

6. Bump up the BL2 size for Juno to accommodate the inclusion of libfdt.

Change-Id: I80f1554adec41753e0d179a5237364f04fe13a3f
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

ARM Platorms: Load TB_FW_CONFIG in BL1 ...

This patch modifies the bl1_platform_setup() API to load and authenticate
TB_FW_CONFIG in BL1. The load address of the same is passed on to BL2 in
`arg0` of entrypoint info. The fvp_io_storage.c and arm_io_storage.c also
adds entries corresponding to TB_FW_CONFIG. A helper function
`arm_load_tb_fw_config()` is added to load and authenticate TB_FW_CONFIG
if present.

Change-Id: Ie7bce667b3fad2b1a083bbcbc0a773f9f04254b1
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

Build: change the first parameter of TOOL_ADD_IMG to lowercase ...

In the next commit, I need the image name in lowercase because
output files are generally named in lowercase.

Unfortunately, TOOL_ADD_IMG takes the first argument in uppercase
since we generally use uppercase Make variables.

make_helpers/build_macros.mk provides 'uppercase' macro to convert
a string into uppercase, but 'lowercase' does not exist.  We can
implement it if we like, but it would be more straightforward to
change the argument of TOOL_ADD_IMG.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Build: rename FIP_ADD_IMG to TOOL_ADD_IMG ...

Now FIP_ADD_IMG takes care of both fiptool and cert_create
symmetrically.  Rename it so that it matches the behavior.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Build: merge build macros between FIP_ and FWU_FIP_ ...

The build system supports generating two FIP images, fip and fwu_fip.
Accordingly, we have similar build macros.

   FIP_ADD_PAYLOAD   <-->  FWU_FIP_ADD_PAYLOAD
   CERT_ADD_CMD_OPT  <-->  FWU_CERT_ADD_CMD_OPT
   FIP_ADD_IMG       <-->  FWU_FIP_ADD_IMG

The duplicated code increases the maintenance burden.  Also, the build
rule of BL2U looks clumsy - we want to call MAKE_BL to compile it from
source files, but we want to put it in fwu_fip.  We can not do it in a
single macro call since the current MAKE_BL does not support fwu_fip.

To refactor those in a clean way is to support one more argument to
specify the FIP prefix.  If it is empty, the images are targeted to
fip, whereas if the argument is "FWU_", targeted to fwu_fip.

The build macros prefixed with FWU_ go away.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>