Merge "GICv3: GIC-600: Detect GIC-600 at runtime" into integration

GICv3: GIC-600: Detect GIC-600 at runtime ...

The only difference between GIC-500 and GIC-600 relevant to TF-A is the
differing power management sequence.
A certain GIC implementation is detectable at runtime, for instance by
checking the IIDR register. Let's add that test before initiating the
GIC-600 specific sequence, so the code can be used on both GIC-600 and
GIC-500 chips alike, without deciding on a GIC chip at compile time.

This means that the GIC-500 "driver" is now redundant. To allow minimal
platform support, add a switch to disable GIC-600 support.

Change-Id: I17ea97d9fb05874772ebaa13e6678b4ba3415557
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

dualroot: add chain of trust for secure partitions ...

A new certificate "sip-sp-cert" has been added for Silicon Provider(SiP)
owned Secure Partitions(SP). A similar support for Platform owned SP can
be added in future. The certificate is also protected against anti-
rollback using the trusted Non-Volatile counter.

To avoid deviating from TBBR spec, support for SP CoT is only provided
in dualroot.
Secure Partition content certificate is assigned image ID 31 and SP
images follows after it.

The CoT for secure partition look like below.
+------------------+       +-------------------+
| ROTPK/ROTPK Hash |------>| Trusted Key       |
+------------------+       | Certificate       |
                           | (Auth Image)      |
                          /+-------------------+
                         /                   |
                        /                    |
                       /                     |
                      /                      |
                     L                       v
+------------------+       +-------------------+
| Trusted World    |------>| SiP owned SPs     |
| Public Key       |       | Content Cert      |
+------------------+       | (Auth Image)      |
                        /   +-------------------+
                       /                      |
                      /                      v|
+------------------+ L     +-------------------+
| SP_PKG1 Hash     |------>| SP_PKG1           |
|                  |       | (Data Image)      |
+------------------+       +-------------------+
        .                           .
        .                           .
        .                           .
+------------------+       +-------------------+
| SP_PKG8 Hash     |------>| SP_PKG8           |
|                  |       | (Data Image)      |
+------------------+       +-------------------+

Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ia31546bac1327a3e0b5d37e8b99c808442d5e53f

Merge "marvell: drivers: mochi: specify stream ID for SD/MMC" into integration

drivers: introduce ST ETZPC driver ...

ETZPC stands for Extended TrustZone Protection Controller. It is a
resource conditional access device. It is mainly based on Arm TZPC.

ST ETZPC exposes memory mapped DECPROT cells to set access permissions
to SoC peripheral interfaces as I2C, SPI, DDR controllers, and some
of the SoC internal memories.

ST ETZPC exposes memory mapped TZMA cells to set access permissions
to some SoC internal memories.

Change-Id: I47ce20ffcfb55306dab923153b71e1bcbe2a5570
Co-developed-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

marvell: drivers: mochi: specify stream ID for SD/MMC ...

This patch enables the stream ID for the SD/MMC
controllers via dedicated unit register. Thanks to this
change it is possible to configure properly the
IOMMU in OS and use the SD/MMC interface in a guest
Virtual Machine.

Change-Id: I99cbd2c9882eb558ba01405d3d8a3e969f06e082
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>

Merge "drivers: stm32_reset adapt interface to timeout argument" into integration

drivers: stm32_reset adapt interface to timeout argument ...

Changes stm32mp1 reset driver to API to add a timeout argument
to stm32mp_reset_assert() and stm32mp_reset_deassert() and
a return value.

With a supplied timeout, the functions wait the target reset state
is reached before returning. With a timeout of zero, the functions
simply load target reset state in SoC interface and return without
waiting.

Helper functions stm32mp_reset_set() and stm32mp_reset_release()
use a zero timeout and return without a return code.

This change updates few stm32 drivers and plat/stm32mp1 blé_plat_setup.c
accordingly without any functional change.
functional change.

Change-Id: Ia1a73a15125d3055fd8739c125b70bcb9562c27f
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

Merge "drivers: stm32mp1 clocks: fix debug trace on clock enable/disable" into integration

Merge "drivers: stm32mp1 clocks: enable system clocks during initialization" into integration

Merge "drivers: stm32mp1 clocks: prevent crash on always on clocks" into integration

Merge "drivers: stm32mp1 clocks: add RTC as a gateable clock" into integration

Merge "drivers: stm32mp1 clocks: support shifted clock selector bit masks" into integration

Merge "drivers: stm32mp1 clocks: allow tree lookup for several system clocks" into integration

Cleanup the code for TBBR CoT descriptors ...

CoT used for BL1 and BL2 are moved to tbbr_cot_bl1.c
and tbbr_cot_bl2.c respectively.
Common CoT used across BL1 and BL2 are moved to
tbbr_cot_common.c.

Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I2252ac8a6960b3431bcaafdb3ea4fb2d01b79cf5

drivers: stm32mp1 clocks: fix debug trace on clock enable/disable ...

Adds missing terminal new line character '\n' to debug traces,
fix format as index is an unsigned value and use present tense rather
than past tense in the printed message.

Change-Id: I88c06ef4d3a11d97ff8e96875a3dd0f58a3c98b6
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

drivers: stm32mp1 clocks: enable system clocks during initialization ...

Enable few system clocks at related BL initialization.

Change-Id: I12b35e8cdc128b993de4a1dc4c6e9d52624dd8d9
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

drivers: stm32mp1 clocks: prevent crash on always on clocks ...

Oscillators and PLLs are not gated on stm32mp_clk_enable/disable()
calls. This change prevents functions to panic when called for such
always-on clocks. Gating these clocks is out of the scope of
this change.

Change-Id: Ie730553dea480b529de942446176db9119587832
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

drivers: stm32mp1 clocks: add RTC as a gateable clock ...

Adds RTC clock to the list of the supported clocks. This allows
stm32mp_clk_*() API functions to enable, disable and set and get
rate for the clock RTC clock.

Change-Id: I8efc3f00b1f22d1912f59d1846994e9e646d6614
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

drivers: stm32mp1 clocks: support shifted clock selector bit masks ...

The current implementation optimizes memory consumed by gateable
clock table by storing bit mask and bit shift with 1 byte each.
The issue is that register selector bit masks above the 7th LSBit
cannot be stored.

This change uses the shift info to shift the mask before it is used,
allowing clock selector register bit fields to be spread on the 32 bits
of the register as long as the mask fits in 8 contiguous bit at most.

This change is needed to add the RTC clock to the gateable clocks table.

Change-Id: I8a0fbcbf20ea383fb3d712f5064d2d307e44465d
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

drivers: stm32mp1 clocks: allow tree lookup for several system clocks ...

Oscillators, PLLs and some system clocks can be related straight to
a parent clock. Prior this change were only oscillators and few
clocks supported by this look up. This changes adds PLLs and other
system clocks. This enables for flexible use of clock tree exploration
when computing a clock frequency value.

Change-Id: I15ec98023a7095e3120a6954de59a4799d92c66b
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

plat/stm32: Use generic fdt_get_reg_props_by_name() ...

The STM32 platform port parse DT nodes to find base address to
peripherals. It does this by using its own implementation, even though
this functionality is generic and actually widely useful outside of the
STM32 code.

Re-implement fdt_get_reg_props_by_name() on top of the newly introduced
fdt_get_reg_props_by_index() function, and move it to fdt_wrapper.c.
This is removes the assumption that #address-cells and #size-cells are
always one.

Change-Id: I6d584930262c732b6e0356d98aea50b2654f789d
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

plat/stm32: Implement fdt_read_uint32_default() as a wrapper ...

The STM32 platform code uses its own set of FDT helper functions,
although some of them are fairly generic.

Remove the implementation of fdt_read_uint32_default() and implement it
on top of the newly introduced fdt_read_uint32() function, then convert
all users over.

This also fixes two callers, which were slightly abusing the "default"
semantic.

Change-Id: I570533362b4846e58dd797a92347de3e0e5abb75
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

plat/stm32: Use generic fdt_read_uint32_array() implementation ...

The device tree parsing code for the STM32 platform is using its own FDT
helper functions, some of them being rather generic.
In particular the existing fdt_read_uint32_array() implementation is now
almost identical to the new generic code in fdt_wrappers.c, so we can
remove the ST specific version and adjust the existing callers.

Compared to the original ST implementation the new version takes a
pointer to the DTB as the first argument, and also swaps the order of
the number of cells and the pointer.

Change-Id: Id06b0f1ba4db1ad1f733be40e82c34f46638551a
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Merge "TF-A GICv3 driver: Change API for GICR_IPRIORITYR accessors" into integration

TF-A GICv3 driver: Change API for GICR_IPRIORITYR accessors ...

To support compatibility with previous GICv3 driver version
this patch:
- restores original API for gicr_read_ipriority() and
gicr_wrtite_ipriority() functions;
- adds accessor functions for GICR_XXX0,1 registers, e.g.
GICR_IGROUPR0, GICR_ICFGR0, GICR_ICFGR1, etc.

Change-Id: I796a312a61665ff384e3d9de2f4b3c60f700b43b
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

gic multichip: add support for clayton ...

GIC-Clayton supports multichip operation mode which allows it to connect
upto 16 other GIC-Clayton instances. GIC-Clayton's multichip programming
and operation remains same as GIC-600 with a minor change in the
SPI_BLOCKS and SPI_BLOCK_MIN shifts to accommodate additional SPI
ranges. So identify if the GIC v4 extension is enabled by the platform
makefile and appropriately select the SPI_BLOCKS and SPI_BLOCK_MIN
shifts.

Change-Id: I95fd80ef16af6c7ca09e2335539187b133052d41
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

TF-A: Add GICv4 extension for GIC driver ...

This patch adds support for GICv4 extension.
New `GIC_ENABLE_V4_EXTN` option passed to gicv3.mk makefile
was added, and enables GICv4 related changes when set to 1.
This option defaults to 0.

Change-Id: I30ebe1b7a98d3a54863900f37eda4589c707a288
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

TF-A GICv3 driver: Add extended PPI and SPI range ...

This patch provides support for GICv3.1 extended PPI and SPI
range. The option is enabled by setting to 1 and passing
`GIC_EXT_INTID` build flag to gicv3.mk makefile.
This option defaults to 0 with no extended range support.

Change-Id: I7d09086fe22ea531c5df51a8a1efd8928458d394
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Merge changes from topic "brcm_initial_support" into integration ...

* changes:
  doc: brcm: Add documentation file for brcm stingray platform
  drivers: Add SPI Nor flash support
  drivers: Add iproc spi driver
  drivers: Add emmc driver for Broadcom platforms
  Add BL31 support for Broadcom stingray platform
  Add BL2 support for Broadcom stingray platform
  Add bl31 support common across Broadcom platforms
  Add bl2 setup code common across Broadcom platforms
  drivers: Add support to retrieve plat_toc_flags