Merge pull request #1702 from MISL-EBU-System-SW/patches-18.12 ...

Update code with latest changes from Marvell LSP 18.12

ble: ap807: Switch to PLL mode and update CPU frequency ...

- Update CPU frequency on AP807 to 2GHz for SAR 0x0.
- Increase AVS to 0.88V for 2GHz clock

Change-Id: Ic945b682ab2f8543e34294bfc56c3eae2c5e0c8e
Signed-off-by: Christine Gharzuzi <chrisg@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Merge pull request #1679 from pangupta/master ...

ccn: Introduce API to set and read value of node register

ccn: Introduce API to set and read value of node register ...

Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>

drivers/tzc-dmc620: add driver to setup DMC-620 TZC controller ...

ARM CoreLink DMC-620 Dynamic Memory Controller includes a TZC controller
to setup secure or non-secure regions of DRAM memory. The TZC controller
allows to setup upto eight such regions of memory in DRAM. This driver
provides helper functions to setup the TZC controller within DMC-620.

Change-Id: Iee7692417c2080052bdb7b1c2873a024bc5d1d10
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>

Merge pull request #1682 from MISL-EBU-System-SW/migrate-multi-console ...

Marvell: Migrate to multi console API

plat/marvell: Migrate to multi-console API ...

Migrate Marvell platforms from legacy console API to
multi-console API.

Change-Id: I647f5f49148b463a257a747af05b5f0c967f267c
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

drivers: st: update console driver to support MULTI_CONSOLE_API ...

Signed-off-by: Yann Gautier <yann.gautier@st.com>

stm32mp1: add a new file for UART registers definition ...

Signed-off-by: Yann Gautier <yann.gautier@st.com>

Merge pull request #1676 from Yann-lms/static_analysis ...

Correct some issues found with static analysis tools

cadence: uart: comply to console_register prototype ...

Signed-off-by: Alexei Colin <acolin@isi.edu>

stm32mp1: remove duplicate function declaration ...

It is already in include/drivers/st/stm32mp1_ddr_helpers.h.

Signed-off-by: Yann Gautier <yann.gautier@st.com>

stm32mp1: correct some static analysis tools issues ...

These issues wer found by sparse:

drivers/st/clk/stm32mp1_clk.c:1524:19:
 warning: incorrect type in assignment (different base types)
    expected restricted fdt32_t const [usertype] *pkcs_cell
    got unsigned int const [usertype] *

plat/st/stm32mp1/plat_image_load.c:13:6:
 warning: symbol 'plat_flush_next_bl_params' was not declared.
 Should it be static?
plat/st/stm32mp1/plat_image_load.c:21:16:
 warning: symbol 'plat_get_bl_image_load_info' was not declared.
 Should it be static?
plat/st/stm32mp1/plat_image_load.c:29:13:
 warning: symbol 'plat_get_next_bl_params' was not declared.
 Should it be static?

plat/st/stm32mp1/bl2_io_storage.c:40:10:
 warning: symbol 'block_buffer' was not declared. Should it be static?

Signed-off-by: Yann Gautier <yann.gautier@st.com>

Standardise header guards across codebase ...

All identifiers, regardless of use, that start with two underscores are
reserved. This means they can't be used in header guards.

The style that this project is now to use the full name of the file in
capital letters followed by 'H'. For example, for a file called
"uart_example.h", the header guard is UART_EXAMPLE_H.

The exceptions are files that are imported from other projects:

- CryptoCell driver
- dt-bindings folders
- zlib headers

Change-Id: I50561bf6c88b491ec440d0c8385c74650f3c106e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

plat/arm: Fix types of constants in headers ...

Change-Id: I33eaee8e7c983b3042635a448cb8d689ea4e3a12
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Merge pull request #1646 from Andre-ARM/allwinner/pmic-v2 ...

Allwinner/pmic v2

meson: console: Introduce console driver ...

It has only been tested with a system clock of 24 MHz.

It has only been implemented for the multi console API.

Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

tzc: Fix MISRA defects ...

The definitions FAIL_CONTROL_*_SHIFT were incorrect, they have been
fixed.

The types tzc_region_attributes_t and tzc_action_t have been removed and
replaced by unsigned int because it is not allowed to do logical
operations on enums.

Also, fix some address definitions in arm_def.h.

Change-Id: Id37941d76883f9fe5045a5f0a4224c133c504d8b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

allwinner: Add RSB driver ...

The "Reduced Serial Bus" is an Allwinner specific bus, bearing many
similarities with I2C. It sports a much higher bus frequency, though,
(typically 3 MHz) and requires much less handholding for the typical
task of manipulating slave registers (fire-and-forget).
On most A64 boards this bus is used to connect the PMIC to the SoC.

This driver provides basic primitives to read and write slave registers,
it will be later used by the PMIC code.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

stm32mp1: add an IO to read MMC devices ...

Whereas the GPT table is read with io_block, the binaries to be loaded
(e.g. BL33) cannot use it, as it is not suitable to read them block by
block, or the boot time would be very bad.

Signed-off-by: Yann Gautier <yann.gautier@st.com>

stm32mp1: add an IO to read STM32IMAGE binaries ...

This IO is required to read binaries with STM32 header.
This header is added with the stm32image tool.

Signed-off-by: Yann Gautier <yann.gautier@st.com>

Add new defines for STM32MP1 platform ...

To boot on eMMC or SD-cards, STM32MP1 platform needs:
- GPT_IMAGE_ID to read GPT table on those devices
- STM32_IMAGE_ID and IO_TYPE_STM32IMAGE to read images with STM32 header
- IO_TYPE_MMC to have a IO for MMC devices

Signed-off-by: Yann Gautier <yann.gautier@st.com>

stm32mp1: add sdmmc2 driver ...

This driver is for the STMicroelectronics sdmmc2 IP
which is in STM32MP1 SoC.
It uses the MMC framework, and can address either eMMC or SD-card.

Signed-off-by: Yann Gautier <yann.gautier@st.com>

Merge pull request #1606 from satheesbalya-arm/sb1_2603_misra_plat ...

plat/arm: Fix misra warnings in platform code

plat/arm: Fix misra warnings in platform code ...

Change-Id: Ica944acc474a099219d50b041cfaeabd4f3d362f
Signed-off-by: Sathees Balya <sathees.balya@arm.com>

plat/arm: Move norflash driver to drivers/ folder ...

This way it can be reused by other platforms if needed.

Note that this driver is designed to work with the Versatile Express NOR
flash of Juno and FVP. In said platforms, the memory is organized as an
interleaved memory of two chips with a 16 bit word.

Any platform that wishes to reuse it with a different configuration will
need to modify the driver so that it is more generic.

Change-Id: Ic721758425864e0cf42b7b9b04bf0d9513b6022e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Merge pull request #1587 from antonio-nino-diaz-arm/an/deprecated ...

Remove deprecated interfaces for all platforms

mmc: Update framework to use standard response type ...

Respect official response type and update response to follow
official specification.
All the MMC_RESPONSE_R(_x) are replaced with each corresponding define.

Partly revert 2a82a9c for dw_mmc.c:
Responses R1, R1B and R5 have CRC.

Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>

Remove all other deprecated interfaces and files ...

Change-Id: Icd1cdd42afdc78895a9be6c46b414b0a155cfa63
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

cci400: Remove deprecated driver ...

This driver is deprecated.

Change-Id: Ic6e154a5756e779743b17a329eed4570ccc61389
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>