Merge pull request #1497 from SNG-ARM/master ...

RAS changes for SGI575 platform

Merge pull request #1494 from hzhuang1/pcie_pin ...

Hikey960: configure pins for PCIe controller

Hikey960: configure pins for PCIe controller ...

GPIO_089 connects to PCIE_PERST_N. It needs to be configured as
output low.

Signed-off-by: Kaihua Zhong <zhongkaihua@huawei.com>
Signed-off-by: Xiaowei Song <songxiaowei@hisilicon.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

RAS: SGI: Add flags needed to build components for RAS feature ...

Add the various flags that are required to build the components needed
to enable the RAS feature on SGI575 platform. By default, all flags
are set to 0, disabling building of all corresponding components.

Change-Id: I7f8536fba895043ef6e397cc33ac9126cb572132
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>

RAS: SGI575: Add platform specific RAS changes ...

Add platform specific changes needed to add support for the RAS
feature on SGI575 platform, including adding a mapping for the
CPER buffer being used on SGI575 platform.

Change-Id: I01a982e283609b5c48661307906346fa2738a43b
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>

RAS: SGI: Add platform handler for RAS interrupts ...

Add a platform specific handler for RAS interrupts and configure the
platform RAS interrupts for EL3 handling. The interrupt handler passes
control to StandaloneMM code executing in S-EL0, which populates the
CPER buffer with relevant error information. The handler subsequently
invokes the SDEI client which processes the information in the error
information in the CPER buffer. The helper functions
plat_sgi_get_ras_ev_map and plat_sgi_get_ras_ev_map_size would be
defined for sgi platforms in the subsequent patch, which adds sgi575
specific RAS changes.

Change-Id: I490f16c15d9917ac40bdc0441659b92380108d63
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>

SPM: SGI: Map memory allocated for secure partitions ...

The secure partition manager reserves chunks of memory which are used
for the S-EL0 StandaloneMM image and the buffers required for
communication between the Non-Secure world with the StandaloneMM
image. Add the memory chunks to relevant arrays for mapping the
regions of memory with corresponding attributes.

Change-Id: If371d1afee0a50ca7cacd55e16aeaca949d5062b
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>

ARM platforms: Allow board specific definition of SP stack base ...

The SGI platforms need to allocate memory for CPER buffers. These
platform buffers would be placed between the shared reserved memory
and the per cpu stack memory, thus the need to redefine stack base
pointer for these platforms. This patch allows each board in ARM
platform to define the PLAT_SP_IMAGE_STACK_BASE.

Change-Id: Ib5465448b860ab7ab0f645f7cb278a67acce7be9
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>

SGI: Include arm_spm_def.h in platform_def.h ...

Include arm_spm_def.h in the platform_def.h file. Without this
inclusion, we get build errors like

In file included from services/std_svc/spm/sp_setup.c:12:0:
services/std_svc/spm/sp_setup.c: In function 'spm_sp_setup':
services/std_svc/spm/sp_setup.c:61:57: error: 'PLAT_SPM_BUF_BASE'
  undeclared (first use in this function)
  write_ctx_reg(get_gpregs_ctx(ctx), CTX_GPREG_X0, PLAT_SPM_BUF_BASE);

Now that the platform_def.h includes arm_spm_def.h, remove inclusion
of platform_def.h in arm_spm_def.h to remove the circular dependency.

Change-Id: I5225c8ca33fd8d288849524395e436c3d56daf17
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>

Include board_arm_def.h through the platform's header ...

The board_arm_def.h header file needs to be included via the platform
definition header. Not doing so, results in a redefinition error of
PLAT_ARM_MAX_BL31_SIZE macro, if defined in the platform definition
file.

Change-Id: I1d178f6e8a6a41461e7fbcab9f6813a2faa2d82b
Signed-off-by: Sughosh Ganu <sughosh.ganu@arm.com>

Merge pull request #1486 from antonio-nino-diaz-arm/an/psci-misra ...

Fix several MISRA defects in PSCI library

Merge pull request #1466 from Yann-lms/stm32mp1 ...

Add STMicroelectronics STM32MP1 platform support

Merge pull request #1491 from jeenu-arm/misra-fix ...

Arm platforms: Fix type mismatch for arm_pm_idle_states

Merge pull request #1472 from danielboulby-arm/db/Reclaim ...

Rework page table setup for varying number of mem regions

stm32mp1: Link BL2, BL32 and DTB in one binary ...

platform.mk is updated to have compilation rules for DTB, stm32image tool,
and the concatenation of the 3 binaries.
A new linker script and an assembly file are added to manage this.

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

stm32mp1: Add BL32 SP_min secure monitor ...

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>

stm32mp1: Add DDR support and its security with TZC400 ...

The DDR driver is under dual license, BSD and GPLv2.
The configuration parameters are taken from device tree.

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

stm32mp1: Add PMIC support ...

If a PMIC companion chip is present on board, it has to be configured
for regulators supplies.
This check is done with board DT configuration.

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Pascal Paillet <p.paillet@st.com>

stm32mp1: Add console support ...

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

stm32mp1: save boot information in backup registers ...

This will be used by BL33 to get boot device and instance.

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

stm32mp1: Add GPIO support ...

The management of pinctrl nodes of device tree is also added.

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>

stm32mp1: Add clock and reset support ...

The clock driver is under dual license, BSD and GPLv2.
The clock driver uses device tree, so a minimal support for this is added.
The required files for driver and DTS files are in include/dt-bindings/.

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

Introduce STMicroelectronics STM32MP1 platform ...

STM32MP1 is a microprocessor designed by STMicroelectronics,
based on a dual Arm Cortex-A7.
It is an Armv7-A platform, using dedicated code from TF-A.

STM32MP1 uses BL2 compiled with BL2_AT_EL3.

Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Pascal Paillet <p.paillet@st.com>

Rework page table setup for varying number of mem regions ...

Change arm_setup_page_tables() to take a variable number of memory
regions. Remove coherent memory region from BL1, BL2 and BL2U as
their coherent memory region doesn't contain anything and
therefore has a size of 0. Add check to ensure this
doesn't change without us knowing.

Change-Id: I790054e3b20b056dda1043a4a67bd7ac2d6a3bc0
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>

Merge pull request #1488 from b49020/integration ...

synquacer: Enable optional OP-TEE support

Merge pull request #1485 from jeenu-arm/ras ...

Double-fault and fatal error handling support

synquacer: Enable optional OP-TEE support ...

OP-TEE loading is optional on Developerbox controlled via SCP
firmware. To check if OP-TEE is loaded or not, we use DRAM1 region
info passed by SCP firmware.

Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>

Arm platforms: Fix type mismatch for arm_pm_idle_states ...

This also gets rid of MISRA violations for Rule 8.3 and 8.4.

Change-Id: I45bba011b16f90953dd4b260fcd58381f978eedc
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

PSCI: Fix MISRA defects in platform code ...

Fix violations of MISRA C-2012 Rules 10.1, 10.3, 13.3, 14.4, 17.7 and
17.8.

Change-Id: I6c9725e428b5752f1d80684ec29cb6c52a5c0c2d
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

hikey: include TBB in BL1 ...

BL1 is used in recovery mode on HiKey. The TBB implementation
on HiKey is in BL2. It means that user need to build ATF BL2
with TBB and ATF BL1 with non-TBB. It's inconvenient.

So include TBB in BL1, too.

Signed-off-by: Teddy Reed <teddy@prosauce.org>
Signed-off-by: Victor Chong <victor.chong@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>