Increase type widths to satisfy width requirements ...

Usually, C has no problem up-converting types to larger bit sizes. MISRA
rule 10.7 requires that you not do this, or be very explicit about this.
This resolves the following required rule:

    bl1/aarch64/bl1_context_mgmt.c:81:[MISRA C-2012 Rule 10.7 (required)]<None>
    The width of the composite expression "0U | ((mode & 3U) << 2U) | 1U |
    0x3c0U" (32 bits) is less that the right hand operand
    "18446744073709547519ULL" (64 bits).

This also resolves MISRA defects such as:

    bl2/aarch64/bl2arch_setup.c:18:[MISRA C-2012 Rule 12.2 (required)]
    In the expression "3U << 20", shifting more than 7 bits, the number
    of bits in the essential type of the left expression, "3U", is
    not allowed.

Further, MISRA requires that all shifts don't overflow. The definition of
PAGE_SIZE was (1U << 12), and 1U is 8 bits. This caused about 50 issues.
This fixes the violation by changing the definition to 1UL << 12. Since
this uses 32bits, it should not create any issues for aarch32.

This patch also contains a fix for a build failure in the sun50i_a64
platform. Specifically, these misra fixes removed a single and
instruction,

    92407e73        and     x19, x19, #0xffffffff

from the cm_setup_context function caused a relocation in
psci_cpus_on_start to require a linker-generated stub. This increased the
size of the .text section and caused an alignment later on to go over a
page boundary and round up to the end of RAM before placing the .data
section. This sectionn is of non-zero size and therefore causes a link
error.

The fix included in this reorders the functions during link time
without changing their ording with respect to alignment.

Change-Id: I76b4b662c3d262296728a8b9aab7a33b02087f16
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>

TSP: add PIE support ...

This implementation simply mimics that of BL31.

Change-Id: Ibbaa4ca012d38ac211c52b0b3e97449947160e07
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Refactor ARMv8.3 Pointer Authentication support code ...

This patch provides the following features and makes modifications
listed below:
- Individual APIAKey key generation for each CPU.
- New key generation on every BL31 warm boot and TSP CPU On event.
- Per-CPU storage of APIAKey added in percpu_data[]
  of cpu_data structure.
- `plat_init_apiakey()` function replaced with `plat_init_apkey()`
  which returns 128-bit value and uses Generic timer physical counter
  value to increase the randomness of the generated key.
  The new function can be used for generation of all ARMv8.3-PAuth keys
- ARMv8.3-PAuth specific code placed in `lib\extensions\pauth`.
- New `pauth_init_enable_el1()` and `pauth_init_enable_el3()` functions
  generate, program and enable APIAKey_EL1 for EL1 and EL3 respectively;
  pauth_disable_el1()` and `pauth_disable_el3()` functions disable
  PAuth for EL1 and EL3 respectively;
  `pauth_load_bl31_apiakey()` loads saved per-CPU APIAKey_EL1 from
  cpu-data structure.
- Combined `save_gp_pauth_registers()` function replaces calls to
  `save_gp_registers()` and `pauth_context_save()`;
  `restore_gp_pauth_registers()` replaces `pauth_context_restore()`
  and `restore_gp_registers()` calls.
- `restore_gp_registers_eret()` function removed with corresponding
  code placed in `el3_exit()`.
- Fixed the issue when `pauth_t pauth_ctx` structure allocated space
  for 12 uint64_t PAuth registers instead of 10 by removal of macro
  CTX_PACGAKEY_END from `include/lib/el3_runtime/aarch64/context.h`
  and assigning its value to CTX_PAUTH_REGS_END.
- Use of MODE_SP_ELX and MODE_SP_EL0 macro definitions
  in `msr	spsel`  instruction instead of hard-coded values.
- Changes in documentation related to ARMv8.3-PAuth and ARMv8.5-BTI.

Change-Id: Id18b81cc46f52a783a7e6a09b9f149b6ce803211
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Add support for Branch Target Identification ...

This patch adds the functionality needed for platforms to provide
Branch Target Identification (BTI) extension, introduced to AArch64
in Armv8.5-A by adding BTI instruction used to mark valid targets
for indirect branches. The patch sets new GP bit [50] to the stage 1
Translation Table Block and Page entries to denote guarded EL3 code
pages which will cause processor to trap instructions in protected
pages trying to perform an indirect branch to any instruction other
than BTI.
BTI feature is selected by BRANCH_PROTECTION option which supersedes
the previous ENABLE_PAUTH used for Armv8.3-A Pointer Authentication
and is disabled by default. Enabling BTI requires compiler support
and was tested with GCC versions 9.0.0, 9.0.1 and 10.0.0.
The assembly macros and helpers are modified to accommodate the BTI
instruction.
This is an experimental feature.
Note. The previous ENABLE_PAUTH build option to enable PAuth in EL3
is now made as an internal flag and BRANCH_PROTECTION flag should be
used instead to enable Pointer Authentication.
Note. USE_LIBROM=1 option is currently not supported.

Change-Id: Ifaf4438609b16647dc79468b70cd1f47a623362e
Signed-off-by: Alexei Fedorov <Alexei.Fedorov@arm.com>

Apply stricter speculative load restriction ...

The SCTLR.DSSBS bit is zero by default thus disabling speculative loads.
However, we also explicitly set it to zero for BL2 and TSP images when
each image initialises its context. This is done to ensure that the
image environment is initialised in a safe state, regardless of the
reset value of the bit.

Change-Id: If25a8396641edb640f7f298b8d3309d5cba3cd79
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

TSP: Enable pointer authentication support ...

The size increase after enabling options related to ARMv8.3-PAuth is:

+----------------------------+-------+-------+-------+--------+
|                            |  text |  bss  |  data | rodata |
+----------------------------+-------+-------+-------+--------+
| CTX_INCLUDE_PAUTH_REGS = 1 |   +40 |   +0  |   +0  |   +0   |
|                            |  0.4% |       |       |        |
+----------------------------+-------+-------+-------+--------+
| ENABLE_PAUTH = 1           |  +352 |    +0 |  +16  |   +0   |
|                            |  3.1% |       | 15.8% |        |
+----------------------------+-------+-------+-------+--------+

Results calculated with the following build configuration:

    make PLAT=fvp SPD=tspd DEBUG=1 \
    SDEI_SUPPORT=1                 \
    EL3_EXCEPTION_HANDLING=1       \
    TSP_NS_INTR_ASYNC_PREEMPT=1    \
    CTX_INCLUDE_PAUTH_REGS=1       \
    ENABLE_PAUTH=1

Change-Id: I6cc1fe0b2345c547dcef66f98758c4eb55fe5ee4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Sanitise includes across codebase ...

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928d5b7 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3a282 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca33988b9 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

TSP: Enable cache along with MMU ...

Previously, data caches were disabled while enabling MMU only because of
active stack. Now that we can enable MMU without using stack, we can
enable both MMU and data caches at the same time.

Change-Id: I73f3b8bae5178610e17e9ad06f81f8f6f97734a6
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Add new alignment parameter to func assembler macro ...

Assembler programmers are used to being able to define functions with a
specific aligment with a pattern like this:

    .align X
  myfunction:

However, this pattern is subtly broken when instead of a direct label
like 'myfunction:', you use the 'func myfunction' macro that's standard
in Trusted Firmware. Since the func macro declares a new section for the
function, the .align directive written above it actually applies to the
*previous* section in the assembly file, and the function it was
supposed to apply to is linked with default alignment.

An extreme case can be seen in Rockchip's plat_helpers.S which contains
this code:

  [...]
  endfunc plat_crash_console_putc

  .align 16
  func platform_cpu_warmboot
  [...]

This assembles into the following plat_helpers.o:

  Sections:
  Idx Name                             Size  [...]  Algn
   9 .text.plat_crash_console_putc 00010000  [...]  2**16
  10 .text.platform_cpu_warmboot   00000080  [...]  2**3

As can be seen, the *previous* function actually got the alignment
constraint, and it is also 64KB big even though it contains only two
instructions, because the .align directive at the end of its section
forces the assembler to insert a giant sled of NOPs. The function we
actually wanted to align has the default constraint. This code only
works at all because the linker just happens to put the two functions
right behind each other when linking the final image, and since the end
of plat_crash_console_putc is aligned the start of platform_cpu_warmboot
will also be. But it still wastes almost 64KB of image space
unnecessarily, and it will break under certain circumstances (e.g. if
the plat_crash_console_putc function becomes unused and its section gets
garbage-collected out).

There's no real way to fix this with the existing func macro. Code like

 func myfunc
 .align X

happens to do the right thing, but is still not really correct code
(because the function label is inserted before the .align directive, so
the assembler is technically allowed to insert padding at the beginning
of the function which would then get executed as instructions if the
function was called). Therefore, this patch adds a new parameter with a
default value to the func macro that allows overriding its alignment.

Also fix up all existing instances of this dangerous antipattern.

Change-Id: I5696a07e2fde896f21e0e83644c95b7b6ac79a10
Signed-off-by: Julius Werner <jwerner@chromium.org>

Merge pull request #925 from dp-arm/dp/spdx ...

Use SPDX license identifiers

Use SPDX license identifiers ...

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/

Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Update terminology: standard SMC to yielding SMC ...

Since Issue B (November 2016) of the SMC Calling Convention document
standard SMC calls are renamed to yielding SMC calls to help avoid
confusion with the standard service SMC range, which remains unchanged.

http://infocenter.arm.com/help/topic/com.arm.doc.den0028b/ARM_DEN0028B_SMC_Calling_Convention.pdf

This patch adds a new define for yielding SMC call type and deprecates
the current standard SMC call type. The tsp is migrated to use this new
terminology and, additionally, the documentation and code comments are
updated to use this new terminology.

Change-Id: I0d7cc0224667ee6c050af976745f18c55906a793
Signed-off-by: David Cunado <david.cunado@arm.com>

Add support for GCC stack protection ...

Introduce new build option ENABLE_STACK_PROTECTOR. It enables
compilation of all BL images with one of the GCC -fstack-protector-*
options.

A new platform function plat_get_stack_protector_canary() is introduced.
It returns a value that is used to initialize the canary for stack
corruption detection. Returning a random value will prevent an attacker
from predicting the value and greatly increase the effectiveness of the
protection.

A message is printed at the ERROR level when a stack corruption is
detected.

To be effective, the global data must be stored at an address
lower than the base of the stacks. Failure to do so would allow an
attacker to overwrite the canary as part of an attack which would void
the protection.

FVP implementation of plat_get_stack_protector_canary is weak as
there is no real source of entropy on the FVP. It therefore relies on a
timer's value, which could be predictable.

Change-Id: Icaaee96392733b721fa7c86a81d03660d3c1bc06
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

Simplify translation tables headers dependencies ...

The files affected by this patch don't really depend on `xlat_tables.h`.
By changing the included file it becomes easier to switch between the
two versions of the translation tables library.

Change-Id: Idae9171c490e0865cb55883b19eaf942457c4ccc
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Introduce unified API to zero memory ...

Introduce zeromem_dczva function on AArch64 that can handle unaligned
addresses and make use of DC ZVA instruction to zero a whole block at a
time. This zeroing takes place directly in the cache to speed it up
without doing external memory access.

Remove the zeromem16 function on AArch64 and replace it with an alias to
zeromem. This zeromem16 function is now deprecated.

Remove the 16-bytes alignment constraint on __BSS_START__ in
firmware-design.md as it is now not mandatory anymore (it used to comply
with zeromem16 requirements).

Change the 16-bytes alignment constraints in SP min's linker script to a
8-bytes alignment constraint as the AArch32 zeromem implementation is now
more efficient on 8-bytes aligned addresses.

Introduce zero_normalmem and zeromem helpers in platform agnostic header
that are implemented this way:
* AArch32:
	* zero_normalmem: zero using usual data access
	* zeromem: alias for zero_normalmem
* AArch64:
	* zero_normalmem: zero normal memory  using DC ZVA instruction
	                  (needs MMU enabled)
	* zeromem: zero using usual data access

Usage guidelines: in most cases, zero_normalmem should be preferred.

There are 2 scenarios where zeromem (or memset) must be used instead:
* Code that must run with MMU disabled (which means all memory is
  considered device memory for data accesses).
* Code that fills device memory with null bytes.

Optionally, the following rule can be applied if performance is
important:
* Code zeroing small areas (few bytes) that are not secrets should use
  memset to take advantage of compiler optimizations.

  Note: Code zeroing security-related critical information should use
  zero_normalmem/zeromem instead of memset to avoid removal by
  compilers' optimizations in some cases or misbehaving versions of GCC.

Fixes ARM-software/tf-issues#408

Change-Id: Iafd9663fc1070413c3e1904e54091cf60effaa82
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

Abort preempted TSP STD SMC after PSCI CPU suspend ...

Standard SMC requests that are handled in the secure-world by the Secure
Payload can be preempted by interrupts that must be handled in the
normal world. When the TSP is preempted the secure context is stored and
control is passed to the normal world to handle the non-secure
interrupt. Once completed the preempted secure context is restored. When
restoring the preempted context, the dispatcher assumes that the TSP
preempted context is still stored as the SECURE context by the context
management library.

However, PSCI power management operations causes synchronous entry into
TSP. This overwrites the preempted SECURE context in the context
management library. When restoring back the SECURE context, the Secure
Payload crashes because this context is not the preempted context
anymore.

This patch avoids corruption of the preempted SECURE context by aborting
any preempted SMC during PSCI power management calls. The
abort_std_smc_entry hook of the TSP is called when aborting the SMC
request.

It also exposes this feature as a FAST SMC callable from normal world to
abort preempted SMC with FID TSP_FID_ABORT.

Change-Id: I7a70347e9293f47d87b5de20484b4ffefb56b770
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com>

Define and use no_ret macro where no return is expected ...

There are many instances in ARM Trusted Firmware where control is
transferred to functions from which return isn't expected. Such jumps
are made using 'bl' instruction to provide the callee with the location
from which it was jumped to. Additionally, debuggers infer the caller by
examining where 'lr' register points to. If a 'bl' of the nature
described above falls at the end of an assembly function, 'lr' will be
left pointing to a location outside of the function range. This misleads
the debugger back trace.

This patch defines a 'no_ret' macro to be used when jumping to functions
from which return isn't expected. The macro ensures to use 'bl'
instruction for the jump, and also, for debug builds, places a 'nop'
instruction immediately thereafter (unless instructed otherwise) so as
to leave 'lr' pointing within the function range.

Change-Id: Ib34c69fc09197cfd57bc06e147cc8252910e01b0
Co-authored-by: Douglas Raillard <douglas.raillard@arm.com>
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Remove all non-configurable dead loops ...

Added a new platform porting function plat_panic_handler, to allow
platforms to handle unexpected error situations. It must be
implemented in assembly as it may be called before the C environment
is initialized. A default implementation is provided, which simply
spins.

Corrected all dead loops in generic code to call this function
instead. This includes the dead loop that occurs at the end of the
call to panic().

All unnecesary wfis from bl32/tsp/aarch64/tsp_exceptions.S have
been removed.

Change-Id: I67cb85f6112fa8e77bd62f5718efcef4173d8134

TSP: Allow preemption of synchronous S-EL1 interrupt handling ...

Earlier the TSP only ever expected to be preempted during Standard SMC
processing. If a S-EL1 interrupt triggered while in the normal world, it
will routed to S-EL1 `synchronously` for handling. The `synchronous` S-EL1
interrupt handler `tsp_sel1_intr_entry` used to panic if this S-EL1 interrupt
was preempted by another higher priority pending interrupt which should be
handled in EL3 e.g. Group0 interrupt in GICv3.

With this patch, the `tsp_sel1_intr_entry` now expects `TSP_PREEMPTED` as the
return code from the `tsp_common_int_handler` in addition to 0 (interrupt
successfully handled) and in both cases it issues an SMC with id
`TSP_HANDLED_S_EL1_INTR`. The TSPD switches the context and returns back
to normal world. In case a higher priority EL3 interrupt was pending, the
execution will be routed to EL3 where interrupt will be handled. On return
back to normal world, the pending S-EL1 interrupt which was preempted will
get routed to S-EL1 to be handled `synchronously` via `tsp_sel1_intr_entry`.

Change-Id: I2087c7fedb37746fbd9200cdda9b6dba93e16201

Enable use of FIQs and IRQs as TSP interrupts ...

On a GICv2 system, interrupts that should be handled in the secure world are
typically signalled as FIQs. On a GICv3 system, these interrupts are signalled
as IRQs instead. The mechanism for handling both types of interrupts is the same
in both cases. This patch enables the TSP to run on a GICv3 system by:

1. adding support for handling IRQs in the exception handling code.
2. removing use of "fiq" in the names of data structures, macros and functions.

The build option TSPD_ROUTE_IRQ_TO_EL3 is deprecated and is replaced with a
new build flag TSP_NS_INTR_ASYNC_PREEMPT. For compatibility reasons, if the
former build flag is defined, it will be used to define the value for the
new build flag. The documentation is also updated accordingly.

Change-Id: I1807d371f41c3656322dd259340a57649833065e

Make generic code work in presence of system caches ...

On the ARMv8 architecture, cache maintenance operations by set/way on the last
level of integrated cache do not affect the system cache. This means that such a
flush or clean operation could result in the data being pushed out to the system
cache rather than main memory. Another CPU could access this data before it
enables its data cache or MMU. Such accesses could be serviced from the main
memory instead of the system cache. If the data in the sysem cache has not yet
been flushed or evicted to main memory then there could be a loss of
coherency. The only mechanism to guarantee that the main memory will be updated
is to use cache maintenance operations to the PoC by MVA(See section D3.4.11
(System level caches) of ARMv8-A Reference Manual (Issue A.g/ARM DDI0487A.G).

This patch removes the reliance of Trusted Firmware on the flush by set/way
operation to ensure visibility of data in the main memory. Cache maintenance
operations by MVA are now used instead. The following are the broad category of
changes:

1. The RW areas of BL2/BL31/BL32 are invalidated by MVA before the C runtime is
   initialised. This ensures that any stale cache lines at any level of cache
   are removed.

2. Updates to global data in runtime firmware (BL31) by the primary CPU are made
   visible to secondary CPUs using a cache clean operation by MVA.

3. Cache maintenance by set/way operations are only used prior to power down.

NOTE: NON-UPSTREAM TRUSTED FIRMWARE CODE SHOULD MAKE EQUIVALENT CHANGES IN
ORDER TO FUNCTION CORRECTLY ON PLATFORMS WITH SUPPORT FOR SYSTEM CACHES.

Fixes ARM-software/tf-issues#205

Change-Id: I64f1b398de0432813a0e0881d70f8337681f6e9a

PSCI: Migrate SPDs and TSP to the new platform and framework API ...

The new PSCI frameworks mandates that the platform APIs and the various
frameworks in Trusted Firmware migrate away from MPIDR based core
identification to one based on core index. Deprecated versions of the old
APIs are still present to provide compatibility but their implementations
are not optimal. This patch migrates the various SPDs exisiting within
Trusted Firmware tree and TSP to the new APIs.

Change-Id: Ifc37e7071c5769b5ded21d0b6a071c8c4cab7836

Add support to indicate size and end of assembly functions ...

In order for the symbol table in the ELF file to contain the size of
functions written in assembly, it is necessary to report it to the
assembler using the .size directive.

To fulfil the above requirements, this patch introduces an 'endfunc'
macro which contains the .endfunc and .size directives. It also adds
a .func directive to the 'func' assembler macro.

The .func/.endfunc have been used so the assembler can fail if
endfunc is omitted.

Fixes ARM-Software/tf-issues#295

Change-Id: If8cb331b03d7f38fe7e3694d4de26f1075b278fc
Signed-off-by: Kévin Petit <kevin.petit@arm.com>

Remove coherent memory from the BL memory maps ...

This patch extends the build option `USE_COHERENT_MEMORY` to
conditionally remove coherent memory from the memory maps of
all boot loader stages. The patch also adds necessary
documentation for coherent memory removal in firmware-design,
porting and user guides.

Fixes ARM-Software/tf-issues#106

Change-Id: I260e8768c6a5c2efc402f5804a80657d8ce38773

Add support for PSCI SYSTEM_OFF and SYSTEM_RESET APIs ...

This patch adds support for SYSTEM_OFF and SYSTEM_RESET PSCI
operations. A platform should export handlers to complete the
requested operation. The FVP port exports fvp_system_off() and
fvp_system_reset() as an example.

If the SPD provides a power management hook for system off and
system reset, then the SPD is notified about the corresponding
operation so it can do some bookkeeping. The TSPD exports
tspd_system_off() and tspd_system_reset() for that purpose.

Versatile Express shutdown and reset methods have been removed
from the FDT as new PSCI sys_poweroff and sys_reset services
have been added. For those kernels that do not support yet these
PSCI services (i.e. GICv3 kernel), the original dtsi files have
been renamed to *-no_psci.dtsi.

Fixes ARM-software/tf-issues#218

Change-Id: Ic8a3bf801db979099ab7029162af041c4e8330c8

Merge pull request #189 from achingupta/ag/tf-issues#153 ...

Unmask SError interrupt and clear SCR_EL3.EA bit

Clarify platform porting interface to TSP ...

* Move TSP platform porting functions to new file:
  include/bl32/tsp/platform_tsp.h.

* Create new TSP_IRQ_SEC_PHY_TIMER definition for use by the generic
  TSP interrupt handling code, instead of depending on the FVP
  specific definition IRQ_SEC_PHY_TIMER.

* Rename TSP platform porting functions from bl32_* to tsp_*, and
  definitions from BL32_* to TSP_*.

* Update generic TSP code to use new platform porting function names
  and definitions.

* Update FVP port accordingly and move all TSP source files to:
  plat/fvp/tsp/.

* Update porting guide with above changes.

Note: THIS CHANGE REQUIRES ALL PLATFORM PORTS OF THE TSP TO
      BE UPDATED

Fixes ARM-software/tf-issues#167

Change-Id: Ic0ff8caf72aebb378d378193d2f017599fc6b78f

Unmask SError interrupt and clear SCR_EL3.EA bit ...

This patch disables routing of external aborts from lower exception levels to
EL3 and ensures that a SError interrupt generated as a result of execution in
EL3 is taken locally instead of a lower exception level.

The SError interrupt is enabled in the TSP code only when the operation has not
been directly initiated by the normal world. This is to prevent the possibility
of an asynchronous external abort which originated in normal world from being
taken when execution is in S-EL1.

Fixes ARM-software/tf-issues#153

Change-Id: I157b996c75996d12fd86d27e98bc73dd8bce6cd5

Move TSP private declarations into separate header ...

Move the TSP private declarations out of tsp.h and into a new
header, tsp_private.h. This clarifies the TSP interface to the TSPD.

Change-Id: I39af346eeba3350cadcac56c02d97a5cb978c28b

Call platform_is_primary_cpu() only from reset handler ...

The purpose of platform_is_primary_cpu() is to determine after reset
(BL1 or BL3-1 with reset handler) if the current CPU must follow the
cold boot path (primary CPU), or wait in a safe state (secondary CPU)
until the primary CPU has finished the system initialization.

This patch removes redundant calls to platform_is_primary_cpu() in
subsequent bootloader entrypoints since the reset handler already
guarantees that code is executed exclusively on the primary CPU.

Additionally, this patch removes the weak definition of
platform_is_primary_cpu(), so the implementation of this function
becomes mandatory. Removing the weak symbol avoids other
bootloaders accidentally picking up an invalid definition in case the
porting layer makes the real function available only to BL1.

The define PRIMARY_CPU is no longer mandatory in the platform porting
because platform_is_primary_cpu() hides the implementation details
(for instance, there may be platforms that report the primary CPU in
a system register). The primary CPU definition in FVP has been moved
to fvp_def.h.

The porting guide has been updated accordingly.

Fixes ARM-software/tf-issues#219

Change-Id: If675a1de8e8d25122b7fef147cb238d939f90b5e