There exists a third DMA controller on the hi3660
SoC called the IOMCU DMAC. This controller is used by
peripherals like SPI2 and UART3. Initialize channels 4-7
as non-secure, while 0-3 remain reserved and secure.

Signed-off-by: Ryan Grachek <ryan@edited.us>

Minor cleanup

Many parts of the code were duplicating symbols that are defined in
include/common/bl_common.h. It is better to only use the definitions in
this header.

As all the symbols refer to virtual addresses, they have to be
uintptr_t, not unsigned long. This has also been fixed in bl_common.h.

Change-Id: I204081af78326ced03fb05f69846f229d324c711
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Channel 0 is used to communicate with LPM3, a coprocessor
for power management. Leave it as secure.

Signed-off-by: Ryan Grachek <ryan@edited.us>

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928d5b7 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3a282 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca33988b9 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

This is needed to utilize the DMA controller on the hikey960

Signed-off-by: Ryan Grachek <ryan@edited.us>

Switch to the new console APIs enabled by setting MULTI_CONSOLE_API=1.
Enables building with ERROR_DEPRECATED=1.

Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>

- Migrate to new GIC interfaces.
- Remove unused bl1_init_bl2_mem_layout().
- Migrate to bl31_early_platform_setup2().
- Use PLAT_VIRT_ADDR_SPACE_SIZE and PLAT_PHY_ADDR_SPACE_SIZE.
- Remove references to removed build options.
- Update Makefile paths.

Change-Id: I583fd893555e6535f32d87ed67bbae430b8e6afe
Tested-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Since LOAD_IMAGE_V2 is always enabled in HiKey960 platform. Drop
LOAD_IMAGE v1 to simplify code.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

When some interrupts are configured as group 0 in GICv2, these
interrupts trigger FIQ signal; this results in the Linux kernel panic
by reporting log: "Bad mode in FIQ handler detected on CPU0, code
0x00000000 -- Unknown/Uncategorized".  Unfortunately from kernel side it
has no permission to read the GIC register for group 0 interrupts so we
have no chance to get to know which interrupt is configured as secure
interrupt and cause the kernel panic.

For upper reason, this commit enables FIQ exception handling for
SPD_none case.  If the system has not enabled SPD the FIQ interrupt is
trapped into EL3 and the FIQ handler can report the interrupt number so
we can easily narrow down which FIQ introduce unexpected interrupt.
After enable SPD we can rely on SPD interrupt route model to handle FIQ.

Signed-off-by: Leo Yan <leo.yan@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>

Support BL31 on HiKey960 platform. Implement PSCI.

Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>