spi: stm32_qspi: Add QSPI support ...

Add QSPI support (limited to read interface).
Implements the memory map and indirect modes.
Low level driver based on SPI-MEM operations.

Change-Id: Ied698e6de3c17d977f8b497c81f2e4a0a27c0961
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>

fmc: stm32_fmc2_nand: Add FMC2 driver support ...

Add fmc2_nand driver support. The driver implements
only read interface for NAND devices.

Change-Id: I3cd037e8ff645ce0d217092b96f33ef41cb7a522
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>

Add SPI-NOR framework ...

SPI-NOR framework is based on SPI-MEM framework using
spi_mem_op execution interface.

It implements read functions and allows NOR configuration
up to quad mode.
Default management is 1 data line but it can be overridden
by platform.
It also includes specific quad mode configuration for
Spansion, Micron and Macronix memories.

Change-Id: If49502b899b4a75f6ebc3190f6bde1013651197f
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>

Add SPI-NAND framework ...

This framework supports SPI-NAND and is based on the
SPI-MEM framework for SPI operations. It uses a common high
level access using the io_mtd.

It is limited to the read functionalities.

Default behavior is the basic one data line operation
but it could be overridden by platform.

Change-Id: Icb4e0887c4003a826f47c876479dd004a323a32b
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>

Add SPI-MEM framework ...

This framework supports SPI operations using a common
spi_mem_op structure:
 - command
 - addr
 - dummy
 - data

The framework manages SPI bus configuration:
 - speed
 - bus width (Up to quad mode)
 - chip select

Change-Id: Idc2736c59bfc5ac6e55429eba5d385275ea3fbde
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>

Add raw NAND framework ...

The raw NAND framework supports SLC NAND devices.

It introduces a new high level interface (io_mtd) that
defines operations a driver can register to the NAND framework.
This interface will fill in the io_mtd device specification:
	- device_size
        - erase_size
that could be used by the io_storage interface.

NAND core source file integrates the standard read loop that
performs NAND device read operations using a skip bad block strategy.
A platform buffer must be defined in case of unaligned
data. This buffer must fit to the maximum device page size
defined by PLATFORM_MTD_MAX_PAGE_SIZE.

The raw_nand.c source file embeds the specific NAND operations
to read data.
The read command is a raw page read without any ECC correction.
This can be overridden by a low level driver.
No generic support for write or erase command or software
ECC correction.

NAND ONFI detection is available and can be enabled using
NAND_ONFI_DETECT=1.
For non-ONFI NAND management, platform can define required
information.

Change-Id: Id80e9864456cf47f02b74938cf25d99261da8e82
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>

Merge changes from topic "ld/mtd_framework" into integration ...

* changes:
  io: change seek offset to signed long long
  compiler_rt: Import aeabi_ldivmode.S file and dependencies

Merge "console: 16550: Prepare for skipping initialisation" into integration

io: change seek offset to signed long long ...

IO seek offset can be set to values above UINT32_MAX, this change
changes the seek offset argument from 'ssize_t' to 'signed long long'.
Fixing platform seek functions to match the new interface update.

Change-Id: I25de83b3b7abe5f52a7b0fee36f71e60cac9cfcb
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>

Merge "Unify type of "cpu_idx" across PSCI module." into integration

Unify type of "cpu_idx" across PSCI module. ...

NOTE for platform integrators:
   API `plat_psci_stat_get_residency()` third argument
   `last_cpu_idx` is changed from "signed int" to the
   "unsigned int" type.

Issue / Trouble points
1. cpu_idx is used as mix of `unsigned int` and `signed int` in code
with typecasting at some places leading to coverity issues.

2. Underlying platform API's return cpu_idx as `unsigned int`
and comparison is performed with platform specific defines
`PLAFORM_xxx` which is not consistent

Misra Rule 10.4:
The value of a complex expression of integer type may only be cast to
a type that is narrower and of the same signedness as the underlying
type of the expression.

Based on above points, cpu_idx is kept as `unsigned int` to match
the API's and low-level functions and platform defines are updated
where ever required

Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: Ib26fd16e420c35527204b126b9b91e8babcc3a5c

Merge "rcar_gen3: drivers: ddr: Move DDR drivers out of staging" into integration

Remove redundant declarations. ...

In further patches, we wish to enable -wredundant-decls check as
part of warning flags by default.

Change-Id: I43410d6dbf40361a503c16d94ccf0f4cf29615b7
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>

rcar_gen3: drivers: ddr: Move DDR drivers out of staging ...

Now that DDR drivers are mostly cleaned up , move them out of staging.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: I9de63f847a0ef9ac27a79fb0f848c351fd7f4da6

drivers: add a driver for snoop control unit ...

The SCU connects one to four Cortex-A5/Cortex-A9 processors
to the memory system through the AXI interfaces.

The SCU functions are to:
- maintain data cache coherency between the Cortex-A5/Cortex-A9
  processors
- initiate L2 AXI memory accesses
- arbitrate between Cortex-A5/Cortex-A9 processors requesting
  L2 accesses
- manage ACP accesses.

Snoop Control Unit will enable to snoop on other CPUs caches.
This is very important when it comes to synchronizing data between
CPUs. As an example, there is a high chance that data might be
cache'd and other CPUs can't see the change. In such cases,
if snoop control unit is enabled, data is synchoronized immediately
between CPUs and the changes are visible to other CPUs.

This driver provides functionality to enable SCU as well as enabling
user to know the following
- number of CPUs present
- is a particular CPU operating in SMP mode or AMP mode
- data cache size of a particular CPU
- does SCU has ACP port
- is L2CPRESENT

Change-Id: I0d977970154fa60df57caf449200d471f02312a0
Signed-off-by: Vishnu Banavath <vishnu.banavath@arm.com>

console: 16550: Prepare for skipping initialisation ...

On some platforms the UART might have already been initialised, for
instance by firmware running before TF-A or by a separate management
processor. In this case it would not be need to initialise it again
(doing so could create spurious characters). But more importantly this
saves us from knowing the right baudrate and the right base clock rate
for the UART. This can lead to more robust and versatile firmware builds.

Allow to skip the 16550 UART initialisation and baud rate divisor
programming, by interpreting an input clock rate of "0" to signify this
case. This will just skip the call to console_16550_core_init, but still
will register the console properly.

Users should just pass 0 as the second parameter, the baudrate (third
parameter) will then be ignored as well.

Fix copy & paste typos in comments for the console_16550_register()
function on the way.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Change-Id: I9f8fca5b358f878fac0f31dc411358fd160786ee

Merge "drivers: marvell: comphy-a3700: support SGMII COMPHY power off" into integration

Merge "drivers: marvell: comphy-a3700: fix USB3 powering on when on lane 2" into integration

Merge changes from topic "allwinner_pmic" into integration ...

* changes:
  allwinner: h6: power: Switch to using the AXP driver
  drivers: allwinner: axp: Add AXP805 support

Merge changes from topic "allwinner_pmic" into integration ...

* changes:
  allwinner: Convert AXP803 regulator setup code into a driver
  allwinner: a64: power: Use fdt_for_each_subnode
  allwinner: a64: power: Remove obsolete register check
  allwinner: a64: power: Remove duplicate DT check
  allwinner: Build PMIC bus drivers only in BL31
  allwinner: a64: power: Make sunxi_turn_off_soc static
  allwinner: Merge duplicate code in sunxi_power_down
  allwinner: Clean up PMIC-related error handling
  allwinner: Synchronize PMIC enumerations
  allwinner: Enable clock before resetting I2C/RSB

Merge "cryptocell: add cryptocell 712 RSA 3K support" into integration

allwinner: Convert AXP803 regulator setup code into a driver ...

Previously, the A64/H5 and H6 platforms' PMIC setup code was entirely
independent. However, some H6 boards also need early regulator setup.

Most of the register interface and all of the device tree traversal code
can be reused between the AXP803 and AXP805. The main difference is the
hardware bus interface, so that part is left to the platforms. The
remainder is moved into a driver.

I factored out the bits that were obviously specific to the AXP803;
additional changes for compatibility with other PMICs can be made as
needed.

The only functional change is that rsb_init() now checks the PMIC's chip
ID register against the expected value. This was already being done in
the H6 version of the code.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Icdcf9edd6565f78cccc503922405129ac27e08a2

drivers: allwinner: axp: Add AXP805 support ...

This adds the new regulator list, as well as changes to make the switch
(equivalent to DC1SW on the AXP803) work on both PMICs.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I9a1eac8ddfc54b27096c10a8eebdd51aaf9b8311

drivers: marvell: comphy-a3700: support SGMII COMPHY power off ...

Add support for powering off the SGMII COMPHY (on lanes 0 and 1).
This is needed sometimes on Turris Mox when using KEXEC.

There is also another benefit of a little energy saving when the given
network interface is down.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I55ae0fe3627e7cc0f65c78a00771939d8bf5399f

drivers: marvell: comphy-a3700: fix USB3 powering on when on lane 2 ...

When USB3 is on lane 2 and indirect register access is used, the polling
at the end of the mvebu_a3700_comphy_usb3_power_on function is
incorrect.

The LOOPBACK_REG0 register should not be used at all. Instead we have to
write the LANE_STATUS1 register address (with offset
USB3PHY_LANE2_REG_BASE_OFFSET) into the indirect address register and
then we should poll indirect data register.

This fixes problems on Turris Mox, which uses lane 2 for USB3.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I968b0cccee5ddbe10a2b5614e52e52d87682aacd

cryptocell: add cryptocell 712 RSA 3K support ...

Add the support needed to enable using CryptoCell integration with
with RSA 3K support.

Signed-off-by: Gilad Ben-Yossef <gilad.benyossef@arm.com>
Change-Id: I95527cb0c41ae012109e8968dd20a4ae9fe67f17

Merge changes from topic "bs/libc" into integration ...

* changes:
  libc: Consolidate the size_t and NULL definitions
  libc: Consolidate unified definitions
  libc: Unify intmax_t and uintmax_t on AArch32/64

libc: Consolidate unified definitions ...

As supporting architectures aside from AArch32 and AArch64 is not a
concern, keeping identical definitions in two places for a large part
of the libc seems counterproductive

The int128 types were left un-unified as __int128 is not supported by
gcc on AArch32

Signed-off-by: Bence Szépkúti <bence.szepkuti@arm.com>
Change-Id: Idf08e6fab7e4680d9da62d3c57266ea2d80472cf

Merge "Enable -Wlogical-op always" into integration

Merge "Enable -Wshadow always" into integration