This patch replaces all references to the SCP Firmware (BL0, BL30,
BL3-0, bl30) with the image terminology detailed in the TF wiki
(https://github.com/ARM-software/arm-trusted-firmware/wiki):

    BL0          -->  SCP_BL1
    BL30, BL3-0  -->  SCP_BL2
    bl30         -->  scp_bl2

This change affects code, documentation, build system, tools and
platform ports that load SCP firmware. ARM plaforms have been
updated to the new porting API.

IMPORTANT: build option to specify the SCP FW image has changed:

    BL30 --> SCP_BL2

IMPORTANT: This patch breaks compatibility for platforms that use BL2
to load SCP firmware. Affected platforms must be updated as follows:

    BL30_IMAGE_ID --> SCP_BL2_IMAGE_ID
    BL30_BASE --> SCP_BL2_BASE
    bl2_plat_get_bl30_meminfo() --> bl2_plat_get_scp_bl2_meminfo()
    bl2_plat_handle_bl30() --> bl2_plat_handle_scp_bl2()

Change-Id: I24c4c1a4f0e4b9f17c9e4929da815c4069549e58

For CSS based platforms, the constants MHU_SECURE_BASE and
MHU_SECURE_SIZE used to define the extents of the Trusted Mailboxes.
As such, they were misnamed because the mailboxes are completely
unrelated to the MHU hardware.

This patch removes the MHU_SECURE_BASE and MHU_SECURE_SIZE #defines.
The address of the Trusted Mailboxes is now relative to the base of
the Trusted SRAM.

This patch also introduces a new constant, SCP_COM_SHARED_MEM_BASE,
which is the address of the first memory region used for communication
between AP and SCP. This is used by the BOM and SCPI protocols.

Change-Id: Ib200f057b19816bf05e834d111271c3ea777291f

There has been a breaking change in the communication protocols used
between the AP cores and the SCP on CSS based platforms like Juno.
This means both the AP Trusted Firmware and SCP firmware must be
updated at the same time.

In case the user forgets to update the SCP ROM firmware, this patch
detects when it still uses the previous version of the communication
protocol. It will then output a comprehensive error message that helps
trouble-shoot the issue.

Change-Id: I7baf8f05ec0b7d8df25e0ee53df61fe7be0207c2

The communication protocol used between the AP cores and the SCP
in CSS-based platforms like Juno has undergone a number of changes.
This patch makes the required modifications to the SCP Boot Protocol,
SCPI Protocol and MHU driver code in shared CSS platform code so that
the AP cores are still able to communicate with the SCP.

This patch focuses on the mandatory changes to make it work. The
design of this code needs to be improved but this will come in
a subsequent patch.

The main changes are:

 - MHU communication protocol

   - The command ID and payload size are no longer written into the
     MHU registers directly. Instead, they are stored in the payload
     area. The MHU registers are now used only as a doorbell to kick
     off messages. Same goes for any command result, the AP has to
     pick it up from the payload area.

 - SCP Boot Protocol

   - The BL3-0 image is now expected to embed a checksum. This
     checksum must be passed to the SCP, which uses it to check the
     integrity of the image it received.

   - The BL3-0 image used to be transferred a block (4KB)
     at a time. The SCP now supports receiving up to 128KB at a
     time, which is more than the size of the BL3-0 image.
     Therefore, the image is now sent in one go.

   - The command IDs have changed.

 - SCPI Protocol

   - The size of the SCPI payload has been reduced down from 512
     bytes to 256 bytes. This changes the base address of the
     AP-to-SCP payload area.

   - For commands that have a response, the response is the same SCPI
     header that was sent, except for the size and the status, which
     both must be updated appropriately. Success/Failure of a command
     is determined by looking at the updated status code.

   - Some command IDs have changed.

NOTE: THIS PATCH BREAKS COMPATIBILITY WITH FORMER VERSIONS OF THE SCP
FIRMWARE AND THUS REQUIRES AN UPDATE OF THIS BINARY. THE LATEST SCP
BINARY CAN BE OBTAINED FROM THE ARM CONNECTED COMMUNITY WEBSITE.

Change-Id: Ia5f6b95fe32401ee04a3805035748e8ef6718da7

This major change pulls out the common functionality from the
FVP and Juno platform ports into the following categories:

*   (include/)plat/common. Common platform porting functionality that
typically may be used by all platforms.

*   (include/)plat/arm/common. Common platform porting functionality
that may be used by all ARM standard platforms. This includes all
ARM development platforms like FVP and Juno but may also include
non-ARM-owned platforms.

*   (include/)plat/arm/board/common. Common platform porting
functionality for ARM development platforms at the board
(off SoC) level.

*   (include/)plat/arm/css/common. Common platform porting
functionality at the ARM Compute SubSystem (CSS) level. Juno
is an example of a CSS-based platform.

*   (include/)plat/arm/soc/common. Common platform porting
functionality at the ARM SoC level, which is not already defined
at the ARM CSS level.

No guarantees are made about the backward compatibility of
functionality provided in (include/)plat/arm.

Also remove any unnecessary variation between the ARM development
platform ports, including:

*   Unify the way BL2 passes `bl31_params_t` to BL3-1. Use the
Juno implementation, which copies the information from BL2 memory
instead of expecting it to persist in shared memory.

*   Unify the TZC configuration. There is no need to add a region
for SCP in Juno; it's enough to simply not allow any access to
this reserved region. Also set region 0 to provide no access by
default instead of assuming this is the case.

*   Unify the number of memory map regions required for ARM
development platforms, although the actual ranges mapped for each
platform may be different. For the FVP port, this reduces the
mapped peripheral address space.

These latter changes will only be observed when the platform ports
are migrated to use the new common platform code in subsequent
patches.

Change-Id: Id9c269dd3dc6e74533d0e5116fdd826d53946dc8