zynqmp: pm: Added NODE_IPI_RPU_0 node definition in pm_defs ...

Nodes represent IPI dedicated to the RPU (not accessible by APU)

Signed-off-by: Mirela Simonovic <mirela.simonovic@aggios.com>

zynqmp: Add support for generic_delay_timer ...

Initialize the generic_delay_timer in the zynqmp port.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>

rockchip: fixes the gic panic for rk3399 resume ...

We make sure the resuming of gic need to be enabled.
Otherwise, The resume will hit the below panic.
...
[   24.230541] CPU0: update max cpu_capacity 451
[   24.236029] CPU5: update max cpu_capacity 1024
[   24.236046] CPU4: shutdown
[   24.243205] psci: CPU4 killed.
[   24.258730] CPU5: shutdown
[   24.261472] psci: CPU5 killed.
[   24.270417] GIC: unable to set SRE (disabled at EL2), panic ahead
[   24.270417] cat[7801]: undefined instruction: pc=ffffffc0004e65d0
[   24.270417] Code: b0003940 91274400 97f871af d2801e00 (d5184600)
[   24.270417] Internal error: Oops - undefined instruction: 0 [#1] PREEMPT

Change-Id: Ie9542c8d5768ba0accfa073453da8bfe06d4f921

Support for Mediatek MT6795 SoC ...

This patch support single core to boot to Linux kernel
through Trusted Firmware.
It also support 32 bit kernel and 64 bit kernel booting.

rockchip: fixes some typo ...

As the checkpatch reports the warning or error.

plat/rockchip/common/plat_pm.c:96:
ERROR: do not set execute permissions for source files
plat/rockchip/rk3399/drivers/pmu/pmu.c:294:
ERROR: do not set execute permissions for source files

plat/rockchip/common/plat_pm.c:286: WARNING: line over 80 characters
plat/rockchip/common/plat_pm.c:287: WARNING: line over 80 characters

Change-Id: Ib347da21c56551c31df3f90f03777b13c75d5c26

rockchip: SIP call use 32 bit return value for rk3399 ...

for compatible 32bit and 64bit, we use 0x82xxxxxx as function ID,
we modify SIP call function return value to 32 bit.

Change-Id: Ib99b03a9ea423853aaa296dcc634ee82c622a552

rockchip: set gpio2 ~ gpio4 to input and pull none mode ...

For save power cosumption, if gpio power supply shut down, we need to
set gpio2 ~ gpio4 to input and HiZ status when suspend, and recovery
they status when rusume. we do it base on apio pass from loader.

Change-Id: I59fd2395e5e37e63425472a39f519822c9197e4c

rockchip: support disable/enable specific gpio when suspend/resume ...

some specific board need to disable/enable specific gpio when
suspend/resume, so we add this function, bootloader can pass the
specific gpio, and we can handle these gpios in bl31 suspend/resuem
function.

Change-Id: I373b03ef9202ee4a05a2b9caacdfa01b47ee2177

rockchip/rk3399: improve gpio driver and support get pull mode function ...

We may need gpio pull mode later, so add this function.
Besides fix a set pull mode bug, and save gpio clock gate,
when operate the gpio, we will enable gpio clock, when
finish gpio operate, restore gpio clock gate status.

Change-Id: Ia1d602804f571a17f5ddc499908663b968b02974

rockchip: fix the scu idle for rk3399 ...

As rk3399 reported the d8/octane scores drop 10% with cpu idle.
The root cause is thc cpu cluster enter the slow mode.
We don't need switch the clock to 24MHz if cpu cluster enter the
retention mode. In order to improve performance, it just needs for
cluster enter powering off mode.

Also, we shouldn't do anything for hlvl if the system is off.

Change-Id: I2a02962a01343abd0cba47ed63192c1cdf88b119

Merge pull request #691 from rockchip-linux/fixes-suspend/resume-bugs ...

Fixes suspend/resume bugs

Merge pull request #684 from rockchip-linux/add-sdram-for-rk3399 ...

rockchip: add dram driver for rk3399

rockchip: handle some interrupt before enter power mode for rk3399 ...

For the PMU design, we don't expect to get the interrupts before enter
the power mode. Since that will cause the confusion for the state
machine in the power mode.

Change-Id: Id8dee79ae617a66271b5caf92caf35f520f45099

rockchip: remove the unused code for rk3399 ...

Change-Id: I986d64df9dc62354d50ccea0468b90f090a44160
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

rockchip: on rk3399 enable Schmitt trigger on 32 kHz clock ...

If we don't enable the Schmitt trigger on the 32 kHz clock then systems
won't always resume from suspend properly.  Presumably anything else in
the system that relies on the 32 kHz clock also will have problems
without the Schmitt trigger enabled.

Enable it always since having the 32 kHz clock on GPIO0_A0 isn't
exactly an optional feature, so all boards using rk3399 will need this.

Change-Id: Idc18c6cd1adc5be5f60efd9cb805d83d5cd40129

rockchip: enable or disable auto power down base on frequency ...

add auto_pd_dis_freq parameter, we can pass a frequency from kernel
to disable or enable ddr auto power down function.

Change-Id: Ie30914701336c59047c380381c6b75dd76a89562

rockchip: rk3399: add dram driver ...

add dram driver, and kernel can through sip function talk to bl31 to
do ddr frequency scaling. and ddr auto powerdown.

Change-Id: I0d0f2869aed95e336c6e23ba96a9310985c84840

rockchip: on rk3399 init the PMU counts at boot; set 24M/32k properly ...

In a previous change we mistakenly thought that PMU_24M_EN_CFG directly
controlled whether the PMU counts ran off the 32k vs. 24M clock.
Apparently that's not true.  Real logic is now documented in code.

Also in the previous change we mistaknely though that PMU_24M_EN_CFG was
normally supposed to be 1 and we should "restore" it at resume time.
This is a terrible idea and made the system totally unreliable after
resume.  Apparently PMU_24M_EN_CFG should always be 0 with all the
current code and settings.

Let's fix the above two problems.  While we're changing all of this,
let's also:

1. Init at boot time.  Many of these counts are used when the system is
   running normally.  We want the behavior at boot to match the behavior
   after suspend/resume.

2. Init CPU counts to be 1 us.  Although old code was trying to set this
   to 1 ms (1000x slower) at suspend/resume time, we've been testing the
   kernel with 1 us for a long time now.  That's because the kernel (at
   boot time) set these values to 24.  Let's keep at 24 until we know
   that's wrong.

3. Init GPU counts to be 1 us.  Old code wasn't touching the GPU, but as
   documented in comments it makes sense to init here.  Do it.

4. Document the crap out of this code, since the SoC's behavior is
   confusing and poorly documented in the TRM.

5. Increase some stabilization times to 30 ms (from 3 ms).  It's unclear
   that a full 30 ms is needed, but let's be safe for now.

This also inits the counts for the GPU.

(Thanks to Doug's patch that come from https://crosreview.com/372381)

Change-Id: Id1bc159a5a99916aeab043895e5c4585c4adab22

Merge pull request #687 from sandrine-bailleux-arm/sb/panic-handler ...

Add WFI in platform's unexpected error handlers

Add WFI in platform's unexpected error handlers ...

This patch adds a WFI instruction in the default implementations of
plat_error_handler() and plat_panic_handler(). This potentially reduces
power consumption by allowing the hardware to enter a low-power state.
The same change has been made to the FVP and Juno platform ports.

Change-Id: Ia4e6e1e5bf1ed42efbba7d0ebbad7be8d5f9f173

Merge pull request #678 from soby-mathew/sm/PSCI_AArch32 ...

Introduce AArch32 support for PSCI library

rockchip: fix the reset-hold release for rk3399 resume ...

The pmusgrf reset-hold bits needs to be released, since the
pmusgrf reset-hold bits needs to be held.

Change-Id: Ia1eccc8fba18294f26b4cc07d47bc5e513dd9a1f

rockchip: fix the power up/dowm cnt for rk3399 ...

Sometimes this will cause the long delay for suspend/resume.
Since the 24M OCS will be turned off in power mode.
Also, remove the ERROR_DEPRECATED config define.

Change-Id: I78f21c35912c2250972e551695cdacc7bc4c020a

rockchip: update to handle PWMs for rk3399 ...

This patch updates some things for rk3399, as following:

1) Add the new file to handle the pwm. (e.g. the pwm regulator)
Make sure that good deal with the pwm related things.
Also, remove some pwm setting for pmu.c.

2) Set the plls slow mode and bypass in suspend, and restore them.

Change-Id: I112806700bf433c87763aac23d22fa7e6a7f5264

AArch32: Add FVP support for SP_MIN ...

This patch implements the support for SP_MIN in FVP. The SP_MIN platform
APIs are implemented and the required makefile support is added for FVP.

Change-Id: Id50bd6093eccbd5e38894e3fd2b20d5baeac5452

AArch32: Add essential ARM platform and FVP support ...

This patch adds AArch32 support for FVP and implements common platform APIs
like `plat_get_my_stack`, `plat_set_my_stack`, `plat_my_core_cos` for AArch32.
Only Multi Processor(MP) implementations of these functions are considered in
this patch. The ARM Standard platform layer helpers are implemented for
AArch32 and the common makefiles are modified to cater for both AArch64 and
AArch32 builds. Compatibility with the deprecated platform API is not
supported for AArch32.

Change-Id: Iad228400613eec91abf731b49e21a15bcf2833ea

Migrate platform makefile to new console driver location ...

This patch migrates the upstream platform makefiles to include the
console drivers from the new location in ARM Trusted Firmware code
base.

Change-Id: I866d6c4951e475de1f836ce8a8c1d5e6da9577e3

Merge pull request #674 from rockchip-linux/Support-PWMs-for-rk3399-suspend/resume ...

rockchip: fixes typo and some bugs for suspend/resume tests

Merge pull request #671 from antonio-nino-diaz-arm/an/unoptimised-mem ...

ARM platforms: Define common image sizes

rockchip: fixes typo and some bugs for suspend/resume tests ...

1. Remove the AP_PWROFF in ATF, should configure it in kernel.
2. Save and restore the PWMs pin/regs for suspend/resume.
3. The pmusgrf reset-hold bits needs to be released. since the
   pmusgrf reset-hold bits needs to be held.
4. Configure the PMU power up/down cycles about delay 3ms.
5. With the MMIO register block as one big mapping.
6. Fix the build error with psci_entrypoint since PSCI lib updated.

Fixes the commit
9ec78bd ("rockchip: support the suspend/resume for rk3399").

Change-Id: I112806700bf433c87763aac23d22fa7e6a7f5264