Poplar: Initialize security properties of IP blocks. ...

The security properties of some IP blocks are configured to secure mode
after reset. This means these IP blocks can only be accessed by cpus
in secure state by default. These should be configured correclty as needed.

Signed-off-by: y00241285 <yyangwei.yangwei@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>

poplar: Increase FIP_SIZE ...

This is currently the maximum allowed without affecting bootup.

Signed-off-by: Victor Chong <victor.chong@linaro.org>

poplar: Rename PLAT_ARM_NS_IMAGE_OFFSET ...

to PLAT_POPLAR_NS_IMAGE_OFFSET

Signed-off-by: Victor Chong <victor.chong@linaro.org>

poplar: Fix GPIO_MAX ...

Per
https://github.com/sdrobertw/Poplar/blob/master/HardwareDocs/Processor_Datasheet_v2XX.pdf
there are 13 groups of GPIO controllers, not 12.

Signed-off-by: Victor Chong <victor.chong@linaro.org>

Merge pull request #1178 from davidcunado-arm/dc/enable_sve ...

Enable SVE for Non-secure world

Hikey960: Change to use recommended power state id format ...

ARM Power State Coordination Interface (ARM DEN 0022D) chapter
6.5 "Recommended StateID Encoding" defines the state ID which can be
used by platforms. The recommended power states can be presented by
below values; and it divides into three fields, every field has 4 bits
to present power states corresponding to core level, cluster level and
system level.

  0: Run
  1: Standby
  2: Retention
  3: Powerdown

This commit changes to use upper recommended power states definition on
Hikey960; and changes the power state validate function to check the
power state passed from kernel side.

Signed-off-by: Leo Yan <leo.yan@linaro.org>

Do not enable SVE on pre-v8.2 platforms ...

Pre-v8.2 platforms such as the Juno platform does not have
the Scalable Vector Extensions implemented and so the build
option ENABLE_SVE is set to zero.

This has a minor performance improvement with no functional
impact.

Change-Id: Ib072735db7a0247406f8b60e325b7e28b1e04ad1
Signed-off-by: David Cunado <david.cunado@arm.com>

hikey960: Set alignment size 512B for fip building ...

Set alignment size to 512B so finally we can get fip.bin with 512B
alignment. This can avoid stuck issue for 'fastboot' downloading
if USB driver uses DMA for data transferring.

Signed-off-by: Leo Yan <leo.yan@linaro.org>

hikey: Set alignment size 512B for fip building ...

Set alignment size to 512B so finally we can get fip.bin with 512B
alignment. This can avoid stuck issue for 'fastboot' downloading if
USB driver uses DMA for data transferring.

Signed-off-by: Leo Yan <leo.yan@linaro.org>

Fix usage of IMAGE_BLx macros ...

These macros are only defined for corresponding image,
and they are undefined for other images. It means that we have
to use ifdef or defined() instead of relying on being 0 by default.

Change-Id: Iad11efab9830ddf471599b46286e1c56581ef5a7
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Merge pull request #1139 from hzhuang1/fix_edmac ...

Fix edmac

HiKey: make RTC out of reset mode ...

Make RTC out of reset mode since it may be used in UEFI.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

HiKey: init EDMA controller with non secure mode ...

Init EDMA controller with non secure mode. A lot of peripherals are
depend on EDMA controller. But EDMA controller is in secure mode
by default. And this operation has to be executed in secure mode.

Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>

poplar: Migrate to using interrupt properties ...

Change-Id: Ibca6ea29be32783de666e0e0a0481668fc11860f
Signed-off-by: Jeenu Viswambharan <jeenu.viswambharan@arm.com>

Merge pull request #1089 from Leo-Yan/hikey_enable_debug_module ...

Hikey: enable CPU debug module

hikey*: Undef BL32_BASE when building without SPD ...

Otherwise, BL2 tries to load a BL32 image and triggers
assert(result == 0)
in
plat_get_image_source()
in hikey{960}_io_storage.c
in a debug build, or displays
ERROR:   BL2: Failed to load image
in a release build.

Signed-off-by: Victor Chong <victor.chong@linaro.org>

hikey*: Fix typo ...

Signed-off-by: Victor Chong <victor.chong@linaro.org>

Hikey: enable CPU debug module ...

Every CPU has its own debug module and this module is used by JTAG
debugging and coresight tracing. If without enabling it, it's easily to
introduce lockup issue when we enable debugging features.

This patch is to enable CPU debug module when power on CPU; this allows
connecting to all cores through JTAG and used by kernel coresight
driver.

Signed-off-by: Matthias Welwarsky <maw@sysgo.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>

hikey*: Support Trusted OS extra image (OP-TEE header) parsing ...

Signed-off-by: Victor Chong <victor.chong@linaro.org>

hikey*: Add LOAD_IMAGE_V2 support ...

Signed-off-by: Victor Chong <victor.chong@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>

Merge pull request #1069 from Leo-Yan/hikey_enable_watchdog_reset ...

Hikey: enable watchdog reset

HiKey: Rename CPUACTRL reg constants ...

Constants named as *ACTLR* refer in fact to the CPUACTRL_EL1 register.
Since ACTLR and ACTRL_EL1 are different registers this patch renames
these constants for clarity.

Change-Id: I2a9e402dab7b0fcb6e481ee0d8a11eda943ed299
Signed-off-by: Eleanor Bonnici <Eleanor.bonnici@arm.com>

Hikey: enable watchdog reset ...

At the system boot time we need enable watchdog reset, otherwise after
the watchdog is timeout it cannot reset the SoC. We need set the bit 0
and bit 16 together, the bit 16 is mask bit so after set bit 16 we have
permission to operate bit 0 and bit 0 is watchdog reset enabling bit.

Signed-off-by: Leo Yan <leo.yan@linaro.org>

Merge pull request #1053 from jwerner-chromium/JW_func_align ...

Add new alignment parameter to func assembler macro

Hikey960: fix PSCI suspend stuck issue ...

Clear the cpuidle flag when resuming from idle. This flag is set
when entering idle, and if it remains set when resuming, it can
prevent the cluster from powering off during the next system
suspend operation. During system suspend, all CPUs are plugged
out except the last CPU, which is suspended. If any of the
cpuidle flags are set at this point, the last CPU will be stuck
in a WFI loop and will not be powered off.
This problem only occurs during system suspend.

Signed-off-by: Tao Wang <kevin.wangtao@linaro.org>

Add new alignment parameter to func assembler macro ...

Assembler programmers are used to being able to define functions with a
specific aligment with a pattern like this:

    .align X
  myfunction:

However, this pattern is subtly broken when instead of a direct label
like 'myfunction:', you use the 'func myfunction' macro that's standard
in Trusted Firmware. Since the func macro declares a new section for the
function, the .align directive written above it actually applies to the
*previous* section in the assembly file, and the function it was
supposed to apply to is linked with default alignment.

An extreme case can be seen in Rockchip's plat_helpers.S which contains
this code:

  [...]
  endfunc plat_crash_console_putc

  .align 16
  func platform_cpu_warmboot
  [...]

This assembles into the following plat_helpers.o:

  Sections:
  Idx Name                             Size  [...]  Algn
   9 .text.plat_crash_console_putc 00010000  [...]  2**16
  10 .text.platform_cpu_warmboot   00000080  [...]  2**3

As can be seen, the *previous* function actually got the alignment
constraint, and it is also 64KB big even though it contains only two
instructions, because the .align directive at the end of its section
forces the assembler to insert a giant sled of NOPs. The function we
actually wanted to align has the default constraint. This code only
works at all because the linker just happens to put the two functions
right behind each other when linking the final image, and since the end
of plat_crash_console_putc is aligned the start of platform_cpu_warmboot
will also be. But it still wastes almost 64KB of image space
unnecessarily, and it will break under certain circumstances (e.g. if
the plat_crash_console_putc function becomes unused and its section gets
garbage-collected out).

There's no real way to fix this with the existing func macro. Code like

 func myfunc
 .align X

happens to do the right thing, but is still not really correct code
(because the function label is inserted before the .align directive, so
the assembler is technically allowed to insert padding at the beginning
of the function which would then get executed as instructions if the
function was called). Therefore, this patch adds a new parameter with a
default value to the func macro that allows overriding its alignment.

Also fix up all existing instances of this dangerous antipattern.

Change-Id: I5696a07e2fde896f21e0e83644c95b7b6ac79a10
Signed-off-by: Julius Werner <jwerner@chromium.org>

hikey: Disable VBUS_DET interrupt for PMIC ...

After disconnect Jumper pin 1-2 in J15 header, the signal VBUS_DET is to
be pulled down to low level. This will assert the interrupt signal in
PMIC and trigger IRQ in GIC; the asserted signal from VBUS_DET is level
triggered and kernel reports the warning for unhooked interrupt handling;
and VBUS_DET stays with low level, this triggers IRQ storm in kernel.

This patch is to disable interrupt for VBUS_DET in PMIC, this can
dismiss the verbose log and IRQ storm after kernel booting.

[   40.835279] irq 57: nobody cared (try booting with the "irqpoll" option)
[   40.842075] CPU: 0 PID: 980 Comm: irq/57-hi655x-p Not tainted 4.4.77-568944-g576a0114dec8-dirty #667
[   40.851303] Hardware name: HiKey Development Board (DT)
[   40.856580] Call trace:
[   40.859060] [<ffffff800808c4cc>] dump_backtrace+0x0/0x1e0
[   40.864516] [<ffffff800808c8ac>] show_stack+0x20/0x28
[   40.869622] [<ffffff80084b9688>] dump_stack+0xa8/0xe0
[   40.874729] [<ffffff800812dd5c>] __report_bad_irq+0x40/0xec
[   40.880360] [<ffffff800812e0bc>] note_interrupt+0x1e4/0x2d8
[   40.885992] [<ffffff800812b11c>] handle_irq_event_percpu+0xd8/0x268
[   40.892324] [<ffffff800812b2f8>] handle_irq_event+0x4c/0x7c
[   40.897955] [<ffffff800812ecbc>] handle_level_irq+0xcc/0x178
[   40.903672] [<ffffff800812a778>] generic_handle_irq+0x34/0x4c
[   40.909481] [<ffffff80085074c8>] pl061_irq_handler+0xa8/0x124
[   40.915286] [<ffffff800812a778>] generic_handle_irq+0x34/0x4c
[   40.921092] [<ffffff800812a820>] __handle_domain_irq+0x90/0xf8
[   40.926985] [<ffffff8008082620>] gic_handle_irq+0x58/0xa8

Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>

Merge pull request #1029 from islmit01/im/fix_includes ...

Fix order of includes

Merge pull request #1005 from ldts/v1 ...

Poplar: Initial commit for Poplar E-96Boards

Merge pull request #1028 from vchong/bl32_optee_support_v2 ...

hikey: Add BL32 (OP-TEE) support v2