Merge pull request #1879 from pbeesley-arm/pb/todo-removal ...

Pb/todo removal

Merge pull request #1858 from thloh85-intel/dwmmc_fixes ...

drivers: synopsys: Fix synopsys MMC driver

plat/arm: mhu: make mhu driver generic ...

MHU doorbell driver requires arm platform specific
macro "PLAT_CSS_MHU_BASE".
Rename it to "PLAT_MHUV2_BASE", so that platforms other than arm
can use generic MHU doorbell driver.

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>

drivers: Remove TODO from io_storage ...

This TODO was added five years ago so I assume that there is not
going to be a shutdown API added after all.

Change-Id: If0f4e2066454df773bd9bf41ed65d3a10248a2d3
Signed-off-by: Paul Beesley <paul.beesley@arm.com>

drivers: synopsys: Fix synopsys MMC driver ...

There are some issues with synopsys MMC driver:
- CMD8 should not expect data (for SD)
- ACMD51 should expect data (Send SCR for SD)
- dw_prepare should not dictate size to be MMC_BLOCK_SIZE, block size is
now handled in the dw_prepare function
- after the CMD completes, when doing dw_read, we need to invalidate cache
and wait for the data transfer to complete
- Need to set FIFO threshold, otherwise DMA might never get the interrupt
to read or write

Signed-off-by: Tien Hock, Loh <tien.hock.loh@intel.com>

Merge pull request #1863 from thloh85-intel/mmc_fixes ...

drivers: mmc: Fix some issues with MMC stack

drivers: mmc: Fix some issues with MMC stack ...

Some bugs in MMC stack needs to be fixed:
- scr cannot be local as this will cause cache issue when invalidating
after the read DMA transfer is completed
- ACMD41 needs to send voltage information in initialization, otherwise the
command is a query, thus will not initialize the controller
- when checking device state, retry until the retries counter goes to zero
before failing

Signed-off-by: Tien Hock, Loh <tien.hock.loh@intel.com>

rpi3: sdhost: SDHost driver improvement ...

This commit improves the SDHost driver for RPi3 as following:
 * Unblock MMC_CMD(17). Using MMC_CMD(17) is more efficient on
   block reading.
 * In some low probability that SEND_OP_COND might results CRC7
   error. We can consider that the command runs correctly. We don't
   need to retry this command so removing the code for retry.
 * Using MMC_BUS_WIDTH_1 as MMC default value to improve the stability.
 * Increase the clock to 50Mhz in data mode to speed up the io.
 * Change the pull resistors configuration to gain more stability.

Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>

stm32mp1: add minimal support for co-processor Cortex-M4 ...

STM32MP1 chip embeds a dual Cortex-A7 and a Cortex-M4.
The support for Cortex-M4 clocks is added when configuring the clock tree.
Some minimal security features to allow communications between A7 and M4
are also added.

Change-Id: I60417e244a476f60a2758f4969700b2684056665
Signed-off-by: Yann Gautier <yann.gautier@st.com>

stm32mp1: update clock driver ...

Remove useless private structure in function prototypes.
Add a reference counter on clocks.
Prepare for future secured/shared/non-secured clocks.

Change-Id: I3dbed81721da5ceff5e10b2c4155b1e340c036ee
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>

stm32mp1: add timeout detection in reset driver ...

This change makes the platform to panic in case of peripheral reset
resource malfunction.

Change-Id: I17eb9cb045b78a4e5142a8c33b744e84992d732a
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>

stm32mp1: split clkfunc code ...

Create a new file stm32mp_clkfunc.c to put functions that could be common
between several platforms.

Change-Id: Ica915c796b162b2345056b33328acc05035a242c
Signed-off-by: Yann Gautier <yann.gautier@st.com>

stm32mp1: update I2C and PMIC drivers ...

Regulator configuration at boot takes more information from DT.
I2C configuration from DT is done in I2C driver.
I2C driver manages more transfer modes.
The min voltage of buck1 should also be increased to 1.2V,
else the platform does not boot.

Heavily modifies stm32_i2c.c since many functions move inside the source
file to remove redundant declarations.

Change-Id: I0bee5d776cf3ff15e687427cd6abc06ab237d025
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>

stm32mp1: use new functions to manage timeouts ...

Remove the previously use function: get_timer, and use new functions
timeout_init_us and timeout_elapsed.

Change-Id: I4e95b123648bff7ca91e40462a2a3ae24cfe1697
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Nicolas LE BAYON <nicolas.le.bayon@st.com>

stm32mp1: make functions and macros more common ...

Mainly remove suffix 1 from prefix stm32mp1 in several macros and functions
that can be used in drivers shared by different platforms.

Change-Id: I2295c44f5b1edac7e80a93c0e8dfd671b36e88e7
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>

rpi3: Add SDHost driver ...

This commit adds SDHost driver for RaspberryPi3. SDHost driver uses the
GPIO driver to connect the SDCard and SDHost. By using this driver it is
able to read/write raw blocks on SDCard.

Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>

Merge pull request #1773 from grandpaul/rpi3-gpio-driver ...

Rpi3 gpio driver

rpi3: Add GPIO driver ...

This commit adds GPIO driver for RaspberryPi3. The GPIO driver for RPi3
also provides the way to do pinmux selections.

Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>

fvp: pwrc: Move to drivers/ folder ...

Change-Id: I670ea80e0331c2d4b2ccfa563a45469a43f6902d
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

plat/arm: sds: Move to drivers/ folder ...

Change-Id: Ia601d5ad65ab199e747fb60af4979b7db477d249
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

plat/arm: scp: Move to drivers/ folder ...

Change-Id: Ida5dae39478654405d0ee31a6cbddb4579e76a7f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

plat/arm: scpi: Move to drivers/ folder ...

Change-Id: Icc59cdaf2b56f6936e9847f1894594c671db2e94
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

plat/arm: mhu: Move to drivers/ folder ...

Change-Id: I656753a1825ea7340a3708b950fa6b57455e9056
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

plat/arm: scmi: Move to drivers/ folder ...

Change-Id: I8989d2aa0258bf3b50a856c5b81532d578600124
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

ti: k3: common: Add support for runtime detection of GICR base address ...

Valid addresses for GICR base are always a set calculable distance from
the GICD and is based on the number of cores a given instance of GICv3 IP
can support. The formula for the number of address bits is given by the
ARM GIC-500 TRM section 3.2 as 2^(18+log2(cores)) with the MSB set to
one for GICR instances. Holes in the GIC address space are also
guaranteed to safely return 0 on reads. This allows us to support runtime
detection of the GICR base address by starting from GIC base address plus
BIT(18) and walking until the GICR ID register (IIDR) is detected. We
stop searching after BIT(20) to prevent searching out into space if
something goes wrong. This can be extended out if we ever have a device
with 16 or more cores.

Signed-off-by: Andrew F. Davis <afd@ti.com>

stm32mp1: add BSEC driver ...

The BSEC (Boot and Security and OTP control) is intended to control an OTP
(one time programmable) fuse box, used for on-chip non-volatile storage
for device configuration and security parameters.

Change-Id: I38c44684c7b9c6a1f24ec0ae3fe99cec481d5a51
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Mathieu Belou <mathieu.belou@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>

stm32mp1: update device tree and gpio functions ...

Change fdt_check_status function to fdt_get_status.
Update GPIO defines.
Move some functions in gpio driver, instead of dt helper file.
Add GPIO bank helper functions.
Use only one status field in dt_node_info structure including both status
and secure status.

Change-Id: I34f93408dd4aac16ae722f564bc3f7d6ae978cf4
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>

drivers: st: update drivers code ...

Reword some traces.
Use uintptr_t where required.
Reduce scope of variables.
Improve io_stm32image algo.
Complete some IP registers definitions.
Add failure on supported DDR (stm32mp1_ddr_init()).
Fix cache flush on cache disable (stm32mp1_ddr_setup).

Change-Id: Ie02fa71e02b9d69abc807fd5b7df233e5be6668c
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>

drivers: st: pmic: update stpmic1 driver ...

Change-Id: I4a1b281925e0a3a1e2a34b3e363537e4a7f13823
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>

stm32mp1: update device tree files ...

The drivers are also updated to reflect the changes.
Set RCC as non-secure.

Change-Id: I568fa1f418355830ad1d4d1cdcdb910fb362231b
Signed-off-by: Yann Gautier <yann.gautier@st.com>