allwinner: Adjust memory mapping to fit into 256MB ...

At the moment we map as much of the DRAM into EL3 as possible, however
we actually don't use it. The only exception is the secure DRAM for
BL32 (if that is configured).

To decrease the memory footprint of ATF, we save on some page tables by
reducing the memory mapping to the actually required regions: SRAM, device
MMIO, secure DRAM and U-Boot (to be used later).
This introduces a non-identity mapping for the DRAM regions.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

allwinner: Unify platform.mk files ...

For the two different platforms we support in the Allwinner port we
mostly rely on header files covering the differences. This leads to the
platform.mk files in the respective directories to be almost identical.

To avoid further divergence and make sure that one platform doesn't
break accidentally, let's create a shared allwinner-common.mk file and
include that from the platform directory.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

allwinner: Remove references to removed build flags ...

Change-Id: I206478597dd9855d3fe1577e7e2c0fe6d2af1cc5
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

drivers: i2c: mentor: move platform code into header files ...

At the moment we have two I2C stub drivers (for the Allwinner and the
Marvell platform), which #include the actual .c driver file.
Change this into the more usual design, by renaming and moving the stub
drivers into platform specific header files and including these from the
actual driver file. The platform specific include directories make sure
the driver picks up the right header automatically.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

allwinner: sun50i_h6: initialise I2C just before powering down ...

Even though we initialise the platform part and the I2C controller
itself at boot time, we actually only access the bus on power down.
Meanwhile a rich OS might have configured the I2C pins differently or
even disabled the controller.
So repeat the platform setup and controller initialisation just before
we actually access the bus to power off the system. This is safe,
because at this point the rich OS should no longer be running.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

allwinner: sun50i_h6: improve I2C setup ...

Drop the unnecessary check for the I2C pins being already configured as
I2C pins (we actually don't care).
Also avoid resetting *every* peripheral that is covered by the PRCM reset
controller, instead just clear the one line connected to the I2C controller.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

allwinner: implement system power down on H6 w/ AXP805 ...

The AXP805 PMIC used with H6 is capable of shutting down the system.

Add support for using it to shut down the system power.

The original placeholder power off code is moved to A64 code, as it's
still TODO to implement PMIC operations for A64.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

allwinner: sun50i_h6: add initial AXP805 PMIC code ...

The OTT reference design of Allwinner H6 SoC uses an X-Powers AXP805
PMIC.

Add initial code for it.

Currently it's only detected.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

allwinner: call PMIC setup code ...

As the ATF may need to do some power initialization on Allwinner
platform with AXP PMICs, call the PMIC setup code in BL31.

Stub of PMIC setup code is added, to prevent undefined reference.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>

PSCI: Fix types of definitions ...

Also change header guards to fix defects of MISRA C-2012 Rule 21.1.

Change-Id: Ied0d4b0e557ef6119ab669d106d2ac5d99620c57
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Acked-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

allwinner: Add Allwinner H6 SoC support ...

The H6 is Allwinner's most recent SoC. It shares most peripherals with the
other ARMv8 Allwinner SoCs (A64/H5), but has a completely different memory
map.

Introduce a separate platform target, which includes a different header
file to cater for the address differences. Also add the new build target
to the documentation.

The new ATF platform name is "sun50i_h6".

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

allwinner: Detect and output current SoC ...

So far we already support booting on two different SoCs, and we will
shortly add a third, so add some code to determine the current SoC type.
This can be later used to runtime detect certain properties.

Also print the SoC name to the console, to give valuable debug information.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

allwinner: Don't map boot ROM ...

There is nothing we need from the BootROM area, so we also don't need
to map it in EL3.

Remove the mapping and reduce the number of MMAP regions by one.

Reported-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

allwinner: Relax PSCI entry point check ...

The DRAM controller supports up to 4GB of DRAM, and there are actually
boards out there where we can use at least 3GB of this.

Relax the PSCI entry point check, to be not restricted to 2GB of DRAM.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

allwinner: security: Fix SPC guard ...

The "#ifdef SUNXI_SPC_BASE" guard was meant to allow the build on SoCs
without a Secure Peripherals Controller, so that we skip that part of
the security setup. But in the current position this will trigger a
warning about an unused variable.

Simply move the guard one line up to cover the variable as well.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

allwinner: cpu-ops: avoid PSCI on/off output ...

The "INFO" output in sunxi_cpu_ops.c is quite verbose, so make this more
obvious by changing the log level to "VERBOSE" and so avoiding it to
be printed in a normal (even debug) build.

Reported-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

allwinner: sun50i_a64: remove unneeded VER_REG offset ...

The relative VER_REG *offset* is the same across all known SoCs, so we
can define this offset near it's user.

Remove it from the memory map.

Reported-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

allwinner: common: add missing header ...

Some code in sunxi_common.c requires symbols defined in sunxi_private.h,
so add the header to that file.
It was included via another header before, but let's make this explicit.

Reported-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

allwinner: Add BL32 (corresponds to Trusted OS) support ...

This patch is an attempt to run Trusted OS (OP-TEE OS being one of them) along
side BL31 image.

ATF supports multiple SPD's that can take dispatcher name (opteed for OP-TEE OS)
as an input using the 'SPD=<dispatcher name>' option during bl31 build.

Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>

allwinner: Add security setup ...

Some peripherals are TrustZone aware, so they need to be configured to
be accessible from non-secure world, as we don't need any of them being
exclusive to the secure world.
This affects some clocks, DMA channels and the Secure Peripheral
Controller (SPC). The latter controls access to most devices, but is not
active unless booting with the secure boot fuse burnt.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

allwinner: Add platform PSCI functions required for SMP ...

The reset vector entry point is preserved across CPU resets, so it only
needs to be set once at boot.

Hotplugged CPUs are not actually powered down, but are put in a wfi with
the GIC disconnected.

With this commit, Linux is able to enable, hotplug and use all four CPUs.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

allwinner: Add functions to control CPU power/reset ...

sun50i_cpu_on will be used by the PSCI implementation to initialize
secondary cores for SMP. Unfortunately, sun50i_cpu_off is not usable by
PSCI directly, because it is not possible for a CPU to use this function
to power itself down. Power cannot be shut off until the outputs are
clamped, and MMIO does not work once the outputs are clamped.

But at least CPU0 can shutdown the other cores early in the BL31 boot
process and before shutting down the system.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

allwinner: Add Allwinner A64 support ...

The Allwinner A64 SoC is quite popular on single board computers.
It comes with four Cortex-A53 cores in a singe cluster and the usual
peripherals for set-top box/tablet SoC.

The ATF platform target is called "sun50i_a64".

[Andre: adapted to amended directory layout, removed unneeded definitions ]

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

allwinner: Introduce basic platform support ...

This platform supports Allwinner's SoCs with ARMv8 cores. So far they
all sport a single cluster of Cortex-A53 cores.

"sunxi" is the original code name used for this platform, and since it
appears in the Linux kernel and in U-Boot as well, we use it here as a
short file name prefix and for identifiers.

This port includes BL31 support only. U-Boot's SPL takes the role of the
primary loader, also doing the DRAM initialization. It then loads the
rest of the firmware, namely ATF and U-Boot (BL33), then hands execution
over to ATF.

This commit includes the basic platform code shared across all SoCs.
There is no platform.mk yet.

[Andre: moved files into proper directories, supported RESET_TO_BL31,
	various clean ups and simplifications ]

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>