// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (c) 2015, The Linux Foundation. All rights reserved.
*/
#include "msm8916.dtsi"
#include "pm8916.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
#include <dt-bindings/sound/apq8016-lpass.h>
/*
* GPIO name legend: proper name = the GPIO line is used as GPIO
* NC = not connected (pin out but not routed from the chip to
* anything the board)
* "[PER]" = pin is muxed for [peripheral] (not GPIO)
* LSEC = Low Speed External Connector
* HSEC = High Speed External Connector
*
* Line names are taken from the schematic "DragonBoard410c"
* dated monday, august 31, 2015. Page 5 in particular.
*
* For the lines routed to the external connectors the
* lines are named after the 96Boards CE Specification 1.0,
* Appendix "Expansion Connector Signal Description".
*
* When the 96Board naming of a line and the schematic name of
* the same line are in conflict, the 96Board specification
* takes precedence, which means that the external UART on the
* LSEC is named UART0 while the schematic and SoC names this
* UART3. This is only for the informational lines i.e. "[FOO]",
* the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
* ones actually used for GPIO.
*/
/ {
aliases {
serial0 = &blsp1_uart2;
serial1 = &blsp1_uart1;
usid0 = &pm8916_0;
i2c0 = &blsp_i2c2;
i2c1 = &blsp_i2c6;
i2c3 = &blsp_i2c4;
spi0 = &blsp_spi5;
spi1 = &blsp_spi3;
};
chosen {
stdout-path = "serial0";
};
camera_vdddo_1v8: camera-vdddo-1v8 {
compatible = "regulator-fixed";
regulator-name = "camera_vdddo";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
camera_vdda_2v8: camera-vdda-2v8 {
compatible = "regulator-fixed";
regulator-name = "camera_vdda";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-always-on;
};
camera_vddd_1v5: camera-vddd-1v5 {
compatible = "regulator-fixed";
regulator-name = "camera_vddd";
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-always-on;
};
reserved-memory {
ramoops@bff00000{
compatible = "ramoops";
reg = <0x0 0xbff00000 0x0 0x100000>;
record-size = <0x20000>;
console-size = <0x20000>;
ftrace-size = <0x20000>;
};
};
soc {
pinctrl@1000000 {
gpio-line-names =
"[UART0_TX]", /* GPIO_0, LSEC pin 5 */
"[UART0_RX]", /* GPIO_1, LSEC pin 7 */
"[UART0_CTS_N]", /* GPIO_2, LSEC pin 3 */
"[UART0_RTS_N]", /* GPIO_3, LSEC pin 9 */
"[UART1_TX]", /* GPIO_4, LSEC pin 11 */
"[UART1_RX]", /* GPIO_5, LSEC pin 13 */
"[I2C0_SDA]", /* GPIO_8, LSEC pin 17 */
"[I2C0_SCL]", /* GPIO_7, LSEC pin 15 */
"[SPI1_DOUT]", /* SPI1_MOSI, HSEC pin 1 */
"[SPI1_DIN]", /* SPI1_MISO, HSEC pin 11 */
"[SPI1_CS]", /* SPI1_CS_N, HSEC pin 7 */
"[SPI1_SCLK]", /* SPI1_CLK, HSEC pin 9 */
"GPIO-B", /* LS_EXP_GPIO_B, LSEC pin 24 */
"GPIO-C", /* LS_EXP_GPIO_C, LSEC pin 25 */
"[I2C3_SDA]", /* HSEC pin 38 */
"[I2C3_SCL]", /* HSEC pin 36 */
"[SPI0_MOSI]", /* LSEC pin 14 */
"[SPI0_MISO]", /* LSEC pin 10 */
"[SPI0_CS_N]", /* LSEC pin 12 */
"[SPI0_CLK]", /* LSEC pin 8 */
"HDMI_HPD_N", /* GPIO 20 */
"USR_LED_1_CTRL",
"[I2C1_SDA]", /* GPIO_22, LSEC pin 21 */
"[I2C1_SCL]", /* GPIO_23, LSEC pin 19 */
"GPIO-G", /* LS_EXP_GPIO_G, LSEC pin 29 */
"GPIO-H", /* LS_EXP_GPIO_H, LSEC pin 30 */
"[CSI0_MCLK]", /* HSEC pin 15 */
"[CSI1_MCLK]", /* HSEC pin 17 */
"GPIO-K", /* LS_EXP_GPIO_K, LSEC pin 33 */
"[I2C2_SDA]", /* HSEC pin 34 */
"[I2C2_SCL]", /* HSEC pin 32 */
"DSI2HDMI_INT_N",
"DSI_SW_SEL_APQ",
"GPIO-L", /* LS_EXP_GPIO_L, LSEC pin 34 */
"GPIO-J", /* LS_EXP_GPIO_J, LSEC pin 32 */
"GPIO-I", /* LS_EXP_GPIO_I, LSEC pin 31 */
"GPIO-A", /* LS_EXP_GPIO_A, LSEC pin 23 */
"FORCED_USB_BOOT",
"SD_CARD_DET_N",
"[WCSS_BT_SSBI]",
"[WCSS_WLAN_DATA_2]", /* GPIO 40 */
"[WCSS_WLAN_DATA_1]",
"[WCSS_WLAN_DATA_0]",
"[WCSS_WLAN_SET]",
"[WCSS_WLAN_CLK]",
"[WCSS_FM_SSBI]",
"[WCSS_FM_SDI]",
"[WCSS_BT_DAT_CTL]",
"[WCSS_BT_DAT_STB]",
"NC",
"NC", /* GPIO 50 */
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC", /* GPIO 60 */
"NC",
"NC",
"[CDC_PDM0_CLK]",
"[CDC_PDM0_SYNC]",
"[CDC_PDM0_TX0]",
"[CDC_PDM0_RX0]",
"[CDC_PDM0_RX1]",
"[CDC_PDM0_RX2]",
"GPIO-D", /* LS_EXP_GPIO_D, LSEC pin 26 */
"NC", /* GPIO 70 */
"NC",
"NC",
"NC",
"NC", /* GPIO 74 */
"NC",
"NC",
"NC",
"NC",
"NC",
"BOOT_CONFIG_0", /* GPIO 80 */
"BOOT_CONFIG_1",
"BOOT_CONFIG_2",
"BOOT_CONFIG_3",
"NC",
"NC",
"BOOT_CONFIG_5",
"NC",
"NC",
"NC",
"NC", /* GPIO 90 */
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC",
"NC", /* GPIO 100 */
"NC",
"NC",
"NC",
"SSBI_GPS",
"NC",
"NC",
"KEY_VOLP_N",
"NC",
"NC",
"[LS_EXP_MI2S_WS]", /* GPIO 110 */
"NC",
"NC",
"[LS_EXP_MI2S_SCK]",
"[LS_EXP_MI2S_DATA0]",
"GPIO-E", /* LS_EXP_GPIO_E, LSEC pin 27 */
"NC",
"[DSI2HDMI_MI2S_WS]",
"[DSI2HDMI_MI2S_SCK]",
"[DSI2HDMI_MI2S_DATA0]",
"USR_LED_2_CTRL", /* GPIO 120 */
"SB_HS_ID";
};
dma@7884000 {
status = "okay";
};
serial@78af000 {
label = "LS-UART0";
status = "okay";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp1_uart1_default>;
pinctrl-1 = <&blsp1_uart1_sleep>;
};
serial@78b0000 {
label = "LS-UART1";
status = "okay";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp1_uart2_default>;
pinctrl-1 = <&blsp1_uart2_sleep>;
};
i2c@78b6000 {
/* On Low speed expansion */
label = "LS-I2C0";
status = "okay";
};
i2c@78b8000 {
/* On High speed expansion */
label = "HS-I2C2";
status = "okay";
adv_bridge: bridge@39 {
status = "okay";
compatible = "adi,adv7533";
reg = <0x39>;
interrupt-parent = <&msmgpio>;
interrupts = <31 2>;
adi,dsi-lanes = <4>;
clocks = <&rpmcc RPM_SMD_BB_CLK2>;
clock-names = "cec";
pd-gpios = <&msmgpio 32 0>;
avdd-supply = <&pm8916_l6>;
v1p2-supply = <&pm8916_l6>;
v3p3-supply = <&pm8916_l17>;
pinctrl-names = "default","sleep";
pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
#sound-dai-cells = <1>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7533_in: endpoint {
remote-endpoint = <&dsi0_out>;
};
};
port@1 {
reg = <1>;
adv7533_out: endpoint {
remote-endpoint = <&hdmi_con>;
};
};
};
};
};
i2c@78ba000 {
/* On Low speed expansion */
label = "LS-I2C1";
status = "okay";
};
spi@78b7000 {
/* On High speed expansion */
label = "HS-SPI1";
status = "okay";
};
spi@78b9000 {
/* On Low speed expansion */
label = "LS-SPI0";
status = "okay";
};
leds {
pinctrl-names = "default";
pinctrl-0 = <&msmgpio_leds>,
<&pm8916_gpios_leds>,
<&pm8916_mpps_leds>;
compatible = "gpio-leds";
led@1 {
label = "apq8016-sbc:green:user1";
gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
default-state = "off";
};
led@2 {
label = "apq8016-sbc:green:user2";
gpios = <&msmgpio 120 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "mmc0";
default-state = "off";
};
led@3 {
label = "apq8016-sbc:green:user3";
gpios = <&pm8916_gpios 1 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "mmc1";
default-state = "off";
};
led@4 {
label = "apq8016-sbc:green:user4";
gpios = <&pm8916_gpios 2 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "none";
panic-indicator;
default-state = "off";
};
led@5 {
label = "apq8016-sbc:yellow:wlan";
gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "phy0tx";
default-state = "off";
};
led@6 {
label = "apq8016-sbc:blue:bt";
gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "bluetooth-power";
default-state = "off";
};
};
sdhci@7824000 {
vmmc-supply = <&pm8916_l8>;
vqmmc-supply = <&pm8916_l5>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
status = "okay";
};
sdhci@7864000 {
vmmc-supply = <&pm8916_l11>;
vqmmc-supply = <&pm8916_l12>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
cd-gpios = <&msmgpio 38 0x1>;
status = "okay";
};
usb@78d9000 {
extcon = <&usb_id>, <&usb_id>;
status = "okay";
adp-disable;
hnp-disable;
srp-disable;
dr_mode = "otg";
pinctrl-names = "default", "device";
pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>;
pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>;
ulpi {
phy {
v1p8-supply = <&pm8916_l7>;
v3p3-supply = <&pm8916_l13>;
extcon = <&usb_id>;
};
};
};
lpass@7708000 {
status = "okay";
};
mdss@1a00000 {
status = "okay";
mdp@1a01000 {
status = "okay";
};
dsi@1a98000 {
status = "okay";
vdda-supply = <&pm8916_l2>;
vddio-supply = <&pm8916_l6>;
ports {
port@1 {
endpoint {
remote-endpoint = <&adv7533_in>;
data-lanes = <0 1 2 3>;
};
};
};
};
dsi-phy@1a98300 {
status = "okay";
vddio-supply = <&pm8916_l6>;
};
};
lpass_codec: codec{
status = "okay";
};
/*
Internal Codec
playback - Primary MI2S
capture - Ter MI2S
External Primary:
playback - secondary MI2S
capture - Quat MI2S
External Secondary:
playback - Quat MI2S
capture - Quat MI2S
*/
sound: sound {
compatible = "qcom,apq8016-sbc-sndcard";
reg = <0x07702000 0x4>, <0x07702004 0x4>;
reg-names = "mic-iomux", "spkr-iomux";
status = "okay";
pinctrl-0 = <&cdc_pdm_lines_act &ext_sec_tlmm_lines_act &ext_mclk_tlmm_lines_act>;
pinctrl-1 = <&cdc_pdm_lines_sus &ext_sec_tlmm_lines_sus &ext_mclk_tlmm_lines_sus>;
pinctrl-names = "default", "sleep";
qcom,model = "DB410c";
qcom,audio-routing =
"AMIC2", "MIC BIAS Internal2",
"AMIC3", "MIC BIAS External1";
external-dai-link@0 {
link-name = "ADV7533";
cpu { /* QUAT */
sound-dai = <&lpass MI2S_QUATERNARY>;
};
codec {
sound-dai = <&adv_bridge 0>;
};
};
internal-codec-playback-dai-link@0 { /* I2S - Internal codec */
link-name = "WCD";
cpu { /* PRIMARY */
sound-dai = <&lpass MI2S_PRIMARY>;
};
codec {
sound-dai = <&lpass_codec 0>, <&wcd_codec 0>;
};
};
internal-codec-capture-dai-link@0 { /* I2S - Internal codec */
link-name = "WCD-Capture";
cpu { /* PRIMARY */
sound-dai = <&lpass MI2S_TERTIARY>;
};
codec {
sound-dai = <&lpass_codec 1>, <&wcd_codec 1>;
};
};
};
spmi@200f000 {
pm8916@0 {
gpios@c000 {
gpio-line-names =
"USR_LED_3_CTRL",
"USR_LED_4_CTRL",
"USB_HUB_RESET_N_PM",
"USB_SW_SEL_PM";
};
mpps@a000 {
gpio-line-names =
"VDD_PX_BIAS",
"WLAN_LED_CTRL",
"BT_LED_CTRL",
"GPIO-F"; /* LS_EXP_GPIO_F, LSEC pin 28 */
};
};
};
wcnss@a21b000 {
status = "okay";
};
tpiu@820000 { status = "okay"; };
funnel@821000 { status = "okay"; };
replicator@824000 { status = "okay"; };
etf@825000 { status = "okay"; };
etr@826000 { status = "okay"; };
funnel@841000 { status = "okay"; };
debug@850000 { status = "okay"; };
debug@852000 { status = "okay"; };
debug@854000 { status = "okay"; };
debug@856000 { status = "okay"; };
etm@85c000 { status = "okay"; };
etm@85d000 { status = "okay"; };
etm@85e000 { status = "okay"; };
etm@85f000 { status = "okay"; };
cti@810000 { status = "okay"; };
cti@811000 { status = "okay"; };
cti@858000 { status = "okay"; };
cti@859000 { status = "okay"; };
cti@85a000 { status = "okay"; };
cti@85b000 { status = "okay"; };
};
usb2513 {
compatible = "smsc,usb3503";
reset-gpios = <&pm8916_gpios 3 GPIO_ACTIVE_LOW>;
initial-mode = <1>;
};
usb_id: usb-id {
compatible = "linux,extcon-usb-gpio";
id-gpio = <&msmgpio 121 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb_id_default>;
};
hdmi-out {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_con: endpoint {
remote-endpoint = <&adv7533_out>;
};
};
};
gpio-keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
autorepeat;
pinctrl-names = "default";
pinctrl-0 = <&msm_key_volp_n_default>;
button@0 {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
};
};
};
&camss {
status = "ok";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
csiphy0_ep: endpoint {
clock-lanes = <1>;
data-lanes = <0 2>;
remote-endpoint = <&ov5640_ep>;
status = "okay";
};
};
};
};
&cci {
status = "ok";
};
&cci_i2c0 {
camera_rear@3b {
compatible = "ovti,ov5640";
reg = <0x3b>;
enable-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>;
reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&camera_rear_default>;
clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
clock-names = "xclk";
clock-frequency = <23880000>;
vdddo-supply = <&camera_vdddo_1v8>;
vdda-supply = <&camera_vdda_2v8>;
vddd-supply = <&camera_vddd_1v5>;
/* No camera mezzanine by default */
status = "disabled";
port {
ov5640_ep: endpoint {
clock-lanes = <1>;
data-lanes = <0 2>;
remote-endpoint = <&csiphy0_ep>;
};
};
};
};
&spmi_bus {
pm8916_0: pm8916@0 {
pon@800 {
resin {
compatible = "qcom,pm8941-resin";
interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
debounce = <15625>;
bias-pull-up;
linux,code = <KEY_VOLUMEDOWN>;
};
};
};
};
&wcd_codec {
status = "okay";
clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>;
clock-names = "mclk";
qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
};
&smd_rpm_regulators {
vdd_l1_l2_l3-supply = <&pm8916_s3>;
vdd_l4_l5_l6-supply = <&pm8916_s4>;
vdd_l7-supply = <&pm8916_s4>;
s1 {
regulator-min-microvolt = <375000>;
regulator-max-microvolt = <1562000>;
};
s3 {
regulator-min-microvolt = <375000>;
regulator-max-microvolt = <1562000>;
};
s4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
l1 {
regulator-min-microvolt = <375000>;
regulator-max-microvolt = <1525000>;
};
l2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
l3 {
regulator-min-microvolt = <375000>;
regulator-max-microvolt = <1525000>;
};
l4 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l5 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l6 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
l7 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l8 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l9 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l10 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l11 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
regulator-allow-set-load;
regulator-system-load = <200000>;
};
l12 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l13 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l14 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
/**
* 1.8v required on LS expansion
* for mezzanine boards
*/
l15 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
regulator-always-on;
};
l16 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
l17 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
l18 {
regulator-min-microvolt = <1750000>;
regulator-max-microvolt = <3337000>;
};
};
&msmgpio {
msmgpio_leds: msmgpio-leds {
pinconf {
pins = "gpio21", "gpio120";
function = "gpio";
output-low;
};
};
usb_id_default: usb-id-default {
pinmux {
function = "gpio";
pins = "gpio121";
};
pinconf {
pins = "gpio121";
drive-strength = <8>;
input-enable;
bias-pull-up;
};
};
adv7533_int_active: adv533-int-active {
pinmux {
function = "gpio";
pins = "gpio31";
};
pinconf {
pins = "gpio31";
drive-strength = <16>;
bias-disable;
};
};
adv7533_int_suspend: adv7533-int-suspend {
pinmux {
function = "gpio";
pins = "gpio31";
};
pinconf {
pins = "gpio31";
drive-strength = <2>;
bias-disable;
};
};
adv7533_switch_active: adv7533-switch-active {
pinmux {
function = "gpio";
pins = "gpio32";
};
pinconf {
pins = "gpio32";
drive-strength = <16>;
bias-disable;
};
};
adv7533_switch_suspend: adv7533-switch-suspend {
pinmux {
function = "gpio";
pins = "gpio32";
};
pinconf {
pins = "gpio32";
drive-strength = <2>;
bias-disable;
};
};
msm_key_volp_n_default: msm-key-volp-n-default {
pinmux {
function = "gpio";
pins = "gpio107";
};
pinconf {
pins = "gpio107";
drive-strength = <8>;
input-enable;
bias-pull-up;
};
};
};
&pm8916_gpios {
usb_hub_reset_pm: usb-hub-reset-pm {
pinconf {
pins = "gpio3";
function = PMIC_GPIO_FUNC_NORMAL;
input-disable;
output-high;
};
};
usb_hub_reset_pm_device: usb-hub-reset-pm-device {
pinconf {
pins = "gpio3";
function = PMIC_GPIO_FUNC_NORMAL;
output-low;
};
};
usb_sw_sel_pm: usb-sw-sel-pm {
pinconf {
pins = "gpio4";
function = PMIC_GPIO_FUNC_NORMAL;
power-source = <PM8916_GPIO_VPH>;
input-disable;
output-high;
};
};
usb_sw_sel_pm_device: usb-sw-sel-pm-device {
pinconf {
pins = "gpio4";
function = PMIC_GPIO_FUNC_NORMAL;
power-source = <PM8916_GPIO_VPH>;
input-disable;
output-low;
};
};
pm8916_gpios_leds: pm8916-gpios-leds {
pinconf {
pins = "gpio1", "gpio2";
function = PMIC_GPIO_FUNC_NORMAL;
output-low;
};
};
};
&pm8916_mpps {
pinctrl-names = "default";
pinctrl-0 = <&ls_exp_gpio_f>;
ls_exp_gpio_f: pm8916-mpp4 {
pinconf {
pins = "mpp4";
function = "digital";
output-low;
power-source = <PM8916_MPP_L5>; // 1.8V
};
};
pm8916_mpps_leds: pm8916-mpps-leds {
pinconf {
pins = "mpp2", "mpp3";
function = "digital";
output-low;
};
};
};
