/*******************************************************************************
Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved.
Copyright 2011 Freescale Semiconductor, Inc.
* SPDX-License-Identifier: GPL-2.0+
Contact Information:
Linux NICS <linux.nics@intel.com>
Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
*******************************************************************************/
/* e1000_hw.h
* Structures, enums, and macros for the MAC
*/
#ifndef _E1000_HW_H_
#define _E1000_HW_H_
#ifdef E1000_DEBUG
#define DEBUGFUNC() printf("%s\n", __func__);
#else
#define DEBUGFUNC() do { } while (0)
#endif
/* I/O wrapper functions */
#define E1000_WRITE_REG(a, reg, value) \
writel((value), ((a)->hw_addr + E1000_##reg))
#define E1000_READ_REG(a, reg) \
readl((a)->hw_addr + E1000_##reg)
#define E1000_WRITE_REG_ARRAY(a, reg, offset, value) \
writel((value), ((a)->hw_addr + E1000_##reg + ((offset) << 2)))
#define E1000_READ_REG_ARRAY(a, reg, offset) \
readl((a)->hw_addr + E1000_##reg + ((offset) << 2))
#define E1000_WRITE_FLUSH(a) \
do { E1000_READ_REG(a, STATUS); } while (0)
/* Enumerated types specific to the e1000 hardware */
/* Media Access Controlers */
typedef enum {
e1000_undefined = 0,
e1000_82542_rev2_0,
e1000_82542_rev2_1,
e1000_82543,
e1000_82544,
e1000_82540,
e1000_82545,
e1000_82545_rev_3,
e1000_82546,
e1000_82546_rev_3,
e1000_82541,
e1000_82541_rev_2,
e1000_82547,
e1000_82547_rev_2,
e1000_82571,
e1000_82572,
e1000_82573,
e1000_82574,
e1000_80003es2lan,
e1000_ich8lan,
e1000_igb,
e1000_num_macs
} e1000_mac_type;
/* Media Types */
typedef enum {
e1000_media_type_copper = 0,
e1000_media_type_fiber = 1,
e1000_media_type_internal_serdes = 2,
e1000_num_media_types
} e1000_media_type;
typedef enum {
e1000_eeprom_uninitialized = 0,
e1000_eeprom_spi,
e1000_eeprom_microwire,
e1000_eeprom_flash,
e1000_eeprom_ich8,
e1000_eeprom_none, /* No NVM support */
e1000_eeprom_invm,
e1000_num_eeprom_types
} e1000_eeprom_type;
/* Flow Control Settings */
typedef enum {
e1000_fc_none = 0,
e1000_fc_rx_pause = 1,
e1000_fc_tx_pause = 2,
e1000_fc_full = 3,
e1000_fc_default = 0xFF
} e1000_fc_type;
typedef enum {
e1000_phy_m88 = 0,
e1000_phy_igp,
e1000_phy_igp_2,
e1000_phy_gg82563,
e1000_phy_igp_3,
e1000_phy_ife,
e1000_phy_igb,
e1000_phy_bm,
e1000_phy_82580,
e1000_phy_undefined = 0xFF
} e1000_phy_type;
/* Error Codes */
#define E1000_SUCCESS 0
#define E1000_ERR_EEPROM 1
#define E1000_ERR_PHY 2
#define E1000_ERR_CONFIG 3
#define E1000_ERR_PARAM 4
#define E1000_ERR_MAC_TYPE 5
#define E1000_ERR_PHY_TYPE 6
#define E1000_ERR_NOLINK 7
#define E1000_ERR_TIMEOUT 8
#define E1000_ERR_RESET 9
#define E1000_ERR_MASTER_REQUESTS_PENDING 10
#define E1000_ERR_HOST_INTERFACE_COMMAND 11
#define E1000_BLK_PHY_RESET 12
#define E1000_ERR_SWFW_SYNC 13
/* PCI Device IDs */
#define E1000_DEV_ID_82542 0x1000
#define E1000_DEV_ID_82543GC_FIBER 0x1001
#define E1000_DEV_ID_82543GC_COPPER 0x1004
#define E1000_DEV_ID_82544EI_COPPER 0x1008
#define E1000_DEV_ID_82544EI_FIBER 0x1009
#define E1000_DEV_ID_82544GC_COPPER 0x100C
#define E1000_DEV_ID_82544GC_LOM 0x100D
#define E1000_DEV_ID_82540EM 0x100E
#define E1000_DEV_ID_82540EM_LOM 0x1015
#define E1000_DEV_ID_82540EP_LOM 0x1016
#define E1000_DEV_ID_82540EP 0x1017
#define E1000_DEV_ID_82540EP_LP 0x101E
#define E1000_DEV_ID_82545EM_COPPER 0x100F
#define E1000_DEV_ID_82545EM_FIBER 0x1011
#define E1000_DEV_ID_82545GM_COPPER 0x1026
#define E1000_DEV_ID_82545GM_FIBER 0x1027
#define E1000_DEV_ID_82545GM_SERDES 0x1028
#define E1000_DEV_ID_82546EB_COPPER 0x1010
#define E1000_DEV_ID_82546EB_FIBER 0x1012
#define E1000_DEV_ID_82546EB_QUAD_COPPER 0x101D
#define E1000_DEV_ID_82541EI 0x1013
#define E1000_DEV_ID_82541EI_MOBILE 0x1018
#define E1000_DEV_ID_82541ER_LOM 0x1014
#define E1000_DEV_ID_82541ER 0x1078
#define E1000_DEV_ID_82547GI 0x1075
#define E1000_DEV_ID_82541GI 0x1076
#define E1000_DEV_ID_82541GI_MOBILE 0x1077
#define E1000_DEV_ID_82541GI_LF 0x107C
#define E1000_DEV_ID_82546GB_COPPER 0x1079
#define E1000_DEV_ID_82546GB_FIBER 0x107A
#define E1000_DEV_ID_82546GB_SERDES 0x107B
#define E1000_DEV_ID_82546GB_PCIE 0x108A
#define E1000_DEV_ID_82546GB_QUAD_COPPER 0x1099
#define E1000_DEV_ID_82547EI 0x1019
#define E1000_DEV_ID_82547EI_MOBILE 0x101A
#define E1000_DEV_ID_82571EB_COPPER 0x105E
#define E1000_DEV_ID_82571EB_FIBER 0x105F
#define E1000_DEV_ID_82571EB_SERDES 0x1060
#define E1000_DEV_ID_82571EB_QUAD_COPPER 0x10A4
#define E1000_DEV_ID_82571PT_QUAD_COPPER 0x10D5
#define E1000_DEV_ID_82571EB_QUAD_FIBER 0x10A5
#define E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE 0x10BC
#define E1000_DEV_ID_82571EB_SERDES_DUAL 0x10D9
#define E1000_DEV_ID_82571EB_SERDES_QUAD 0x10DA
#define E1000_DEV_ID_82572EI_COPPER 0x107D
#define E1000_DEV_ID_82572EI_FIBER 0x107E
#define E1000_DEV_ID_82572EI_SERDES 0x107F
#define E1000_DEV_ID_82572EI 0x10B9
#define E1000_DEV_ID_82573E 0x108B
#define E1000_DEV_ID_82573E_IAMT 0x108C
#define E1000_DEV_ID_82573L 0x109A
#define E1000_DEV_ID_82574L 0x10D3
#define E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 0x10B5
#define E1000_DEV_ID_80003ES2LAN_COPPER_DPT 0x1096
#define E1000_DEV_ID_80003ES2LAN_SERDES_DPT 0x1098
#define E1000_DEV_ID_80003ES2LAN_COPPER_SPT 0x10BA
#define E1000_DEV_ID_80003ES2LAN_SERDES_SPT 0x10BB
#define E1000_DEV_ID_I350_COPPER 0x1521
#define E1000_DEV_ID_I210_UNPROGRAMMED 0x1531
#define E1000_DEV_ID_I211_UNPROGRAMMED 0x1532
#define E1000_DEV_ID_I210_COPPER 0x1533
#define E1000_DEV_ID_I210_SERDES 0x1536
#define E1000_DEV_ID_I210_1000BASEKX 0x1537
#define E1000_DEV_ID_I210_EXTPHY 0x1538
#define E1000_DEV_ID_I211_COPPER 0x1539
#define E1000_DEV_ID_I210_COPPER_FLASHLESS 0x157b
#define E1000_DEV_ID_I210_SERDES_FLASHLESS 0x157c
#define E1000_DEV_ID_ICH8_IGP_M_AMT 0x1049
#define E1000_DEV_ID_ICH8_IGP_AMT 0x104A
#define E1000_DEV_ID_ICH8_IGP_C 0x104B
#define E1000_DEV_ID_ICH8_IFE 0x104C
#define E1000_DEV_ID_ICH8_IFE_GT 0x10C4
#define E1000_DEV_ID_ICH8_IFE_G 0x10C5
#define E1000_DEV_ID_ICH8_IGP_M 0x104D
#define IGP03E1000_E_PHY_ID 0x02A80390
#define IFE_E_PHY_ID 0x02A80330 /* 10/100 PHY */
#define IFE_PLUS_E_PHY_ID 0x02A80320
#define IFE_C_E_PHY_ID 0x02A80310
#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10 /* 100BaseTx Extended Status,
Control and Address */
#define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY special
control register */
#define IFE_PHY_RCV_FALSE_CARRIER 0x13 /* 100BaseTx Receive false
Carrier Counter */
#define IFE_PHY_RCV_DISCONNECT 0x14 /* 100BaseTx Receive Disconnet
Counter */
#define IFE_PHY_RCV_ERROT_FRAME 0x15 /* 100BaseTx Receive Error
Frame Counter */
#define IFE_PHY_RCV_SYMBOL_ERR 0x16 /* Receive Symbol Error
Counter */
#define IFE_PHY_PREM_EOF_ERR 0x17 /* 100BaseTx Receive
Premature End Of Frame
Error Counter */
#define IFE_PHY_RCV_EOF_ERR 0x18 /* 10BaseT Receive End Of
Frame Error Counter */
#define IFE_PHY_TX_JABBER_DETECT 0x19 /* 10BaseT Transmit Jabber
Detect Counter */
#define IFE_PHY_EQUALIZER 0x1A /* PHY Equalizer Control and
Status */
#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY special control and
LED configuration */
#define IFE_PHY_MDIX_CONTROL 0x1C /* MDI/MDI-X Control register */
#define IFE_PHY_HWI_CONTROL 0x1D /* Hardware Integrity Control
(HWI) */
#define IFE_PESC_REDUCED_POWER_DOWN_DISABLE 0x2000 /* Defaut 1 = Disable auto
reduced power down */
#define IFE_PESC_100BTX_POWER_DOWN 0x0400 /* Indicates the power
state of 100BASE-TX */
#define IFE_PESC_10BTX_POWER_DOWN 0x0200 /* Indicates the power
state of 10BASE-T */
#define IFE_PESC_POLARITY_REVERSED 0x0100 /* Indicates 10BASE-T
polarity */
#define IFE_PESC_PHY_ADDR_MASK 0x007C /* Bit 6:2 for sampled PHY
address */
#define IFE_PESC_SPEED 0x0002 /* Auto-negotiation speed
result 1=100Mbs, 0=10Mbs */
#define IFE_PESC_DUPLEX 0x0001 /* Auto-negotiation
duplex result 1=Full, 0=Half */
#define IFE_PESC_POLARITY_REVERSED_SHIFT 8
#define IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN 0x0100 /* 1 = Dyanmic Power Down
disabled */
#define IFE_PSC_FORCE_POLARITY 0x0020 /* 1=Reversed Polarity,
0=Normal */
#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010 /* 1=Auto Polarity
Disabled, 0=Enabled */
#define IFE_PSC_JABBER_FUNC_DISABLE 0x0001 /* 1=Jabber Disabled,
0=Normal Jabber Operation */
#define IFE_PSC_FORCE_POLARITY_SHIFT 5
#define IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT 4
#define IFE_PMC_AUTO_MDIX 0x0080 /* 1=enable MDI/MDI-X
feature, default 0=disabled */
#define IFE_PMC_FORCE_MDIX 0x0040 /* 1=force MDIX-X,
0=force MDI */
#define IFE_PMC_MDIX_STATUS 0x0020 /* 1=MDI-X, 0=MDI */
#define IFE_PMC_AUTO_MDIX_COMPLETE 0x0010 /* Resolution algorithm
is completed */
#define IFE_PMC_MDIX_MODE_SHIFT 6
#define IFE_PHC_MDIX_RESET_ALL_MASK 0x0000 /* Disable auto MDI-X */
#define IFE_PHC_HWI_ENABLE 0x8000 /* Enable the HWI
feature */
#define IFE_PHC_ABILITY_CHECK 0x4000 /* 1= Test Passed,
0=failed */
#define IFE_PHC_TEST_EXEC 0x2000 /* PHY launch test pulses
on the wire */
#define IFE_PHC_HIGHZ 0x0200 /* 1 = Open Circuit */
#define IFE_PHC_LOWZ 0x0400 /* 1 = Short Circuit */
#define IFE_PHC_LOW_HIGH_Z_MASK 0x0600 /* Mask for indication
type of problem on the line */
#define IFE_PHC_DISTANCE_MASK 0x01FF /* Mask for distance to
the cable problem, in 80cm granularity */
#define IFE_PHC_RESET_ALL_MASK 0x0000 /* Disable HWI */
#define IFE_PSCL_PROBE_MODE 0x0020 /* LED Probe mode */
#define IFE_PSCL_PROBE_LEDS_OFF 0x0006 /* Force LEDs 0 and 2
off */
#define IFE_PSCL_PROBE_LEDS_ON 0x0007 /* Force LEDs 0 and 2 on */
#define NODE_ADDRESS_SIZE 6
#define E1000_82542_2_0_REV_ID 2
#define E1000_82542_2_1_REV_ID 3
#define E1000_REVISION_0 0
#define E1000_REVISION_1 1
#define E1000_REVISION_2 2
#define E1000_REVISION_3 3
#define SPEED_10 10
#define SPEED_100 100
#define SPEED_1000 1000
#define HALF_DUPLEX 1
#define FULL_DUPLEX 2
/* The number of high/low register pairs in the RAR. The RAR (Receive Address
* Registers) holds the directed and multicast addresses that we monitor. We
* reserve one of these spots for our directed address, allowing us room for
* E1000_RAR_ENTRIES - 1 multicast addresses.
*/
#define E1000_RAR_ENTRIES 16
#define MIN_NUMBER_OF_DESCRIPTORS 8
#define MAX_NUMBER_OF_DESCRIPTORS 0xFFF8
/* Receive Descriptor */
struct e1000_rx_desc {
uint64_t buffer_addr; /* Address of the descriptor's data buffer */
uint16_t length; /* Length of data DMAed into data buffer */
uint16_t csum; /* Packet checksum */
uint8_t status; /* Descriptor status */
uint8_t errors; /* Descriptor Errors */
uint16_t special;
};
/* Receive Decriptor bit definitions */
#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
#define E1000_RXD_STAT_IPCS 0x40 /* IP xsum calculated */
#define E1000_RXD_STAT_PIF 0x80 /* passed in-exact filter */
#define E1000_RXD_ERR_CE 0x01 /* CRC Error */
#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */
#define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */
#define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */
#define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */
#define E1000_RXD_ERR_IPE 0x40 /* IP Checksum Error */
#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */
#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */
#define E1000_RXD_SPC_PRI_MASK 0xE000 /* Priority is in upper 3 bits */
#define E1000_RXD_SPC_PRI_SHIFT 0x000D /* Priority is in upper 3 of 16 */
#define E1000_RXD_SPC_CFI_MASK 0x1000 /* CFI is bit 12 */
#define E1000_RXD_SPC_CFI_SHIFT 0x000C /* CFI is bit 12 */
/* mask to determine if packets should be dropped due to frame errors */
#define E1000_RXD_ERR_FRAME_ERR_MASK ( \
E1000_RXD_ERR_CE | \
E1000_RXD_ERR_SE | \
E1000_RXD_ERR_SEQ | \
E1000_RXD_ERR_CXE | \
E1000_RXD_ERR_RXE)
/* Transmit Descriptor */
struct e1000_tx_desc {
uint64_t buffer_addr; /* Address of the descriptor's data buffer */
union {
uint32_t data;
struct {
uint16_t length; /* Data buffer length */
uint8_t cso; /* Checksum offset */
uint8_t cmd; /* Descriptor control */
} flags;
} lower;
union {
uint32_t data;
struct {
uint8_t status; /* Descriptor status */
uint8_t css; /* Checksum start */
uint16_t special;
} fields;
} upper;
};
/* Transmit Descriptor bit definitions */
#define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */
#define E1000_TXD_DTYP_C 0x00000000 /* Context Descriptor */
#define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */
#define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */
#define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */
#define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */
#define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */
#define E1000_TXD_CMD_RS 0x08000000 /* Report Status */
#define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */
#define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */
#define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */
#define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */
#define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */
#define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */
#define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */
#define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */
#define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */
#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */
#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */
#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */
/* Filters */
#define E1000_NUM_UNICAST 16 /* Unicast filter entries */
#define E1000_MC_TBL_SIZE 128 /* Multicast Filter Table (4096 bits) */
#define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */
/* Register Set. (82543, 82544)
*
* Registers are defined to be 32 bits and should be accessed as 32 bit values.
* These registers are physically located on the NIC, but are mapped into the
* host memory address space.
*
* RW - register is both readable and writable
* RO - register is read only
* WO - register is write only
* R/clr - register is read only and is cleared when read
* A - register array
*/
#define E1000_CTRL 0x00000 /* Device Control - RW */
#define E1000_STATUS 0x00008 /* Device Status - RO */
#define E1000_EECD 0x00010 /* EEPROM/Flash Control - RW */
#define E1000_I210_EECD 0x12010 /* EEPROM/Flash Control - RW */
#define E1000_EERD 0x00014 /* EEPROM Read - RW */
#define E1000_I210_EERD 0x12014 /* EEPROM Read - RW */
#define E1000_CTRL_EXT 0x00018 /* Extended Device Control - RW */
#define E1000_MDIC 0x00020 /* MDI Control - RW */
#define E1000_FCAL 0x00028 /* Flow Control Address Low - RW */
#define E1000_FCAH 0x0002C /* Flow Control Address High -RW */
#define E1000_FCT 0x00030 /* Flow Control Type - RW */
#define E1000_VET 0x00038 /* VLAN Ether Type - RW */
#define E1000_ICR 0x000C0 /* Interrupt Cause Read - R/clr */
#define E1000_ITR 0x000C4 /* Interrupt Throttling Rate - RW */
#define E1000_ICS 0x000C8 /* Interrupt Cause Set - WO */
#define E1000_IMS 0x000D0 /* Interrupt Mask Set - RW */
#define E1000_IMC 0x000D8 /* Interrupt Mask Clear - WO */
#define E1000_I210_IAM 0x000E0 /* Interrupt Ack Auto Mask - RW */
#define E1000_RCTL 0x00100 /* RX Control - RW */
#define E1000_FCTTV 0x00170 /* Flow Control Transmit Timer Value - RW */
#define E1000_TXCW 0x00178 /* TX Configuration Word - RW */
#define E1000_RXCW 0x00180 /* RX Configuration Word - RO */
#define E1000_TCTL 0x00400 /* TX Control - RW */
#define E1000_TCTL_EXT 0x00404 /* Extended TX Control - RW */
#define E1000_TIPG 0x00410 /* TX Inter-packet gap -RW */
#define E1000_TBT 0x00448 /* TX Burst Timer - RW */
#define E1000_AIT 0x00458 /* Adaptive Interframe Spacing Throttle - RW */
#define E1000_LEDCTL 0x00E00 /* LED Control - RW */
#define E1000_EXTCNF_CTRL 0x00F00 /* Extended Configuration Control */
#define E1000_EXTCNF_SIZE 0x00F08 /* Extended Configuration Size */
#define E1000_PHY_CTRL 0x00F10 /* PHY Control Register in CSR */
#define E1000_I210_PHY_CTRL 0x00E14 /* PHY Control Register in CSR */
#define FEXTNVM_SW_CONFIG 0x0001
#define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */
#define E1000_PBS 0x01008 /* Packet Buffer Size */
#define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */
#define E1000_I210_EEMNGCTL 0x12030 /* MNG EEprom Control */
#define E1000_FLASH_UPDATES 1000
#define E1000_EEARBC 0x01024 /* EEPROM Auto Read Bus Control */
#define E1000_FLASHT 0x01028 /* FLASH Timer Register */
#define E1000_EEWR 0x0102C /* EEPROM Write Register - RW */
#define E1000_I210_EEWR 0x12018 /* EEPROM Write Register - RW */
#define E1000_FLSWCTL 0x01030 /* FLASH control register */
#define E1000_FLSWDATA 0x01034 /* FLASH data register */
#define E1000_FLSWCNT 0x01038 /* FLASH Access Counter */
#define E1000_FLOP 0x0103C /* FLASH Opcode Register */
#define E1000_ERT 0x02008 /* Early Rx Threshold - RW */
#define E1000_FCRTL 0x02160 /* Flow Control Receive Threshold Low - RW */
#define E1000_FCRTH 0x02168 /* Flow Control Receive Threshold High - RW */
#define E1000_RDBAL 0x02800 /* RX Descriptor Base Address Low - RW */
#define E1000_RDBAH 0x02804 /* RX Descriptor Base Address High - RW */
#define E1000_RDLEN 0x02808 /* RX Descriptor Length - RW */
#define E1000_RDH 0x02810 /* RX Descriptor Head - RW */
#define E1000_RDT 0x02818 /* RX Descriptor Tail - RW */
#define E1000_RDTR 0x02820 /* RX Delay Timer - RW */
#define E1000_RXDCTL 0x02828 /* RX Descriptor Control - RW */
#define E1000_RADV 0x0282C /* RX Interrupt Absolute Delay Timer - RW */
#define E1000_RSRPD 0x02C00 /* RX Small Packet Detect - RW */
#define E1000_TXDMAC 0x03000 /* TX DMA Control - RW */
#define E1000_TDFH 0x03410 /* TX Data FIFO Head - RW */
#define E1000_TDFT 0x03418 /* TX Data FIFO Tail - RW */
#define E1000_TDFHS 0x03420 /* TX Data FIFO Head Saved - RW */
#define E1000_TDFTS 0x03428 /* TX Data FIFO Tail Saved - RW */
#define E1000_TDFPC 0x03430 /* TX Data FIFO Packet Count - RW */
#define E1000_TDBAL 0x03800 /* TX Descriptor Base Address Low - RW */
#define E1000_TDBAH 0x03804 /* TX Descriptor Base Address High - RW */
#define E1000_TDLEN 0x03808 /* TX Descriptor Length - RW */
#define E1000_TDH 0x03810 /* TX Descriptor Head - RW */
#define E1000_TDT 0x03818 /* TX Descripotr Tail - RW */
#define E1000_TIDV 0x03820 /* TX Interrupt Delay Value - RW */
#define E1000_TXDCTL 0x03828 /* TX Descriptor Control - RW */
#define E1000_TADV 0x0382C /* TX Interrupt Absolute Delay Val - RW */
#define E1000_TSPMT 0x03830 /* TCP Segmentation PAD & Min Threshold - RW */
#define E1000_TARC0 0x03840 /* TX Arbitration Count (0) */
#define E1000_TDBAL1 0x03900 /* TX Desc Base Address Low (1) - RW */
#define E1000_TDBAH1 0x03904 /* TX Desc Base Address High (1) - RW */
#define E1000_TDLEN1 0x03908 /* TX Desc Length (1) - RW */
#define E1000_TDH1 0x03910 /* TX Desc Head (1) - RW */
#define E1000_TDT1 0x03918 /* TX Desc Tail (1) - RW */
#define E1000_TXDCTL1 0x03928 /* TX Descriptor Control (1) - RW */
#define E1000_TARC1 0x03940 /* TX Arbitration Count (1) */
#define E1000_CRCERRS 0x04000 /* CRC Error Count - R/clr */
#define E1000_ALGNERRC 0x04004 /* Alignment Error Count - R/clr */
#define E1000_SYMERRS 0x04008 /* Symbol Error Count - R/clr */
#define E1000_RXERRC 0x0400C /* Receive Error Count - R/clr */
#define E1000_MPC 0x04010 /* Missed Packet Count - R/clr */
#define E1000_SCC 0x04014 /* Single Collision Count - R/clr */
#define E1000_ECOL 0x04018 /* Excessive Collision Count - R/clr */
#define E1000_MCC 0x0401C /* Multiple Collision Count - R/clr */
#define E1000_LATECOL 0x04020 /* Late Collision Count - R/clr */
#define E1000_COLC 0x04028 /* Collision Count - R/clr */
#define E1000_DC 0x04030 /* Defer Count - R/clr */
#define E1000_TNCRS 0x04034 /* TX-No CRS - R/clr */
#define E1000_SEC 0x04038 /* Sequence Error Count - R/clr */
#define E1000_CEXTERR 0x0403C /* Carrier Extension Error Count - R/clr */
#define E1000_RLEC 0x04040 /* Receive Length Error Count - R/clr */
#define E1000_XONRXC 0x04048 /* XON RX Count - R/clr */
#define E1000_XONTXC 0x0404C /* XON TX Count - R/clr */
#define E1000_XOFFRXC 0x04050 /* XOFF RX Count - R/clr */
#define E1000_XOFFTXC 0x04054 /* XOFF TX Count - R/clr */
#define E1000_FCRUC 0x04058 /* Flow Control RX Unsupported Count- R/clr */
#define E1000_PRC64 0x0405C /* Packets RX (64 bytes) - R/clr */
#define E1000_PRC127 0x04060 /* Packets RX (65-127 bytes) - R/clr */
#define E1000_PRC255 0x04064 /* Packets RX (128-255 bytes) - R/clr */
#define E1000_PRC511 0x04068 /* Packets RX (255-511 bytes) - R/clr */
#define E1000_PRC1023 0x0406C /* Packets RX (512-1023 bytes) - R/clr */
#define E1000_PRC1522 0x04070 /* Packets RX (1024-1522 bytes) - R/clr */
#define E1000_GPRC 0x04074 /* Good Packets RX Count - R/clr */
#define E1000_BPRC 0x04078 /* Broadcast Packets RX Count - R/clr */
#define E1000_MPRC 0x0407C /* Multicast Packets RX Count - R/clr */
#define E1000_GPTC 0x04080 /* Good Packets TX Count - R/clr */
#define E1000_GORCL 0x04088 /* Good Octets RX Count Low - R/clr */
#define E1000_GORCH 0x0408C /* Good Octets RX Count High - R/clr */
#define E1000_GOTCL 0x04090 /* Good Octets TX Count Low - R/clr */
#define E1000_GOTCH 0x04094 /* Good Octets TX Count High - R/clr */
#define E1000_RNBC 0x040A0 /* RX No Buffers Count - R/clr */
#define E1000_RUC 0x040A4 /* RX Undersize Count - R/clr */
#define E1000_RFC 0x040A8 /* RX Fragment Count - R/clr */
#define E1000_ROC 0x040AC /* RX Oversize Count - R/clr */
#define E1000_RJC 0x040B0 /* RX Jabber Count - R/clr */
#define E1000_MGTPRC 0x040B4 /* Management Packets RX Count - R/clr */
#define E1000_MGTPDC 0x040B8 /* Management Packets Dropped Count - R/clr */
#define E1000_MGTPTC 0x040BC /* Management Packets TX Count - R/clr */
#define E1000_TORL 0x040C0 /* Total Octets RX Low - R/clr */
#define E1000_TORH 0x040C4 /* Total Octets RX High - R/clr */
#define E1000_TOTL 0x040C8 /* Total Octets TX Low - R/clr */
#define E1000_TOTH 0x040CC /* Total Octets TX High - R/clr */
#define E1000_TPR 0x040D0 /* Total Packets RX - R/clr */
#define E1000_TPT 0x040D4 /* Total Packets TX - R/clr */
#define E1000_PTC64 0x040D8 /* Packets TX (64 bytes) - R/clr */
#define E1000_PTC127 0x040DC /* Packets TX (65-127 bytes) - R/clr */
#define E1000_PTC255 0x040E0 /* Packets TX (128-255 bytes) - R/clr */
#define E1000_PTC511 0x040E4 /* Packets TX (256-511 bytes) - R/clr */
#define E1000_PTC1023 0x040E8 /* Packets TX (512-1023 bytes) - R/clr */
#define E1000_PTC1522 0x040EC /* Packets TX (1024-1522 Bytes) - R/clr */
#define E1000_MPTC 0x040F0 /* Multicast Packets TX Count - R/clr */
#define E1000_BPTC 0x040F4 /* Broadcast Packets TX Count - R/clr */
#define E1000_TSCTC 0x040F8 /* TCP Segmentation Context TX - R/clr */
#define E1000_TSCTFC 0x040FC /* TCP Segmentation Context TX Fail - R/clr */
#define E1000_RXCSUM 0x05000 /* RX Checksum Control - RW */
#define E1000_MTA 0x05200 /* Multicast Table Array - RW Array */
#define E1000_RA 0x05400 /* Receive Address - RW Array */
#define E1000_VFTA 0x05600 /* VLAN Filter Table Array - RW Array */
#define E1000_WUC 0x05800 /* Wakeup Control - RW */
#define E1000_WUFC 0x05808 /* Wakeup Filter Control - RW */
#define E1000_WUS 0x05810 /* Wakeup Status - RO */
#define E1000_MANC 0x05820 /* Management Control - RW */
#define E1000_IPAV 0x05838 /* IP Address Valid - RW */
#define E1000_IP4AT 0x05840 /* IPv4 Address Table - RW Array */
#define E1000_IP6AT 0x05880 /* IPv6 Address Table - RW Array */
#define E1000_WUPL 0x05900 /* Wakeup Packet Length - RW */
#define E1000_WUPM 0x05A00 /* Wakeup Packet Memory - RO A */
#define E1000_FFLT 0x05F00 /* Flexible Filter Length Table - RW Array */
#define E1000_FFMT 0x09000 /* Flexible Filter Mask Table - RW Array */
#define E1000_FFVT 0x09800 /* Flexible Filter Value Table - RW Array */
/* Register Set (82542)
*
* Some of the 82542 registers are located at different offsets than they are
* in more current versions of the 8254x. Despite the difference in location,
* the registers function in the same manner.
*/
#define E1000_82542_CTRL E1000_CTRL
#define E1000_82542_STATUS E1000_STATUS
#define E1000_82542_EECD E1000_EECD
#define E1000_82542_EERD E1000_EERD
#define E1000_82542_CTRL_EXT E1000_CTRL_EXT
#define E1000_82542_MDIC E1000_MDIC
#define E1000_82542_FCAL E1000_FCAL
#define E1000_82542_FCAH E1000_FCAH
#define E1000_82542_FCT E1000_FCT
#define E1000_82542_VET E1000_VET
#define E1000_82542_RA 0x00040
#define E1000_82542_ICR E1000_ICR
#define E1000_82542_ITR E1000_ITR
#define E1000_82542_ICS E1000_ICS
#define E1000_82542_IMS E1000_IMS
#define E1000_82542_IMC E1000_IMC
#define E1000_82542_RCTL E1000_RCTL
#define E1000_82542_RDTR 0x00108
#define E1000_82542_RDBAL 0x00110
#define E1000_82542_RDBAH 0x00114
#define E1000_82542_RDLEN 0x00118
#define E1000_82542_RDH 0x00120
#define E1000_82542_RDT 0x00128
#define E1000_82542_FCRTH 0x00160
#define E1000_82542_FCRTL 0x00168
#define E1000_82542_FCTTV E1000_FCTTV
#define E1000_82542_TXCW E1000_TXCW
#define E1000_82542_RXCW E1000_RXCW
#define E1000_82542_MTA 0x00200
#define E1000_82542_TCTL E1000_TCTL
#define E1000_82542_TIPG E1000_TIPG
#define E1000_82542_TDBAL 0x00420
#define E1000_82542_TDBAH 0x00424
#define E1000_82542_TDLEN 0x00428
#define E1000_82542_TDH 0x00430
#define E1000_82542_TDT 0x00438
#define E1000_82542_TIDV 0x00440
#define E1000_82542_TBT E1000_TBT
#define E1000_82542_AIT E1000_AIT
#define E1000_82542_VFTA 0x00600
#define E1000_82542_LEDCTL E1000_LEDCTL
#define E1000_82542_PBA E1000_PBA
#define E1000_82542_RXDCTL E1000_RXDCTL
#define E1000_82542_RADV E1000_RADV
#define E1000_82542_RSRPD E1000_RSRPD
#define E1000_82542_TXDMAC E1000_TXDMAC
#define E1000_82542_TXDCTL E1000_TXDCTL
#define E1000_82542_TADV E1000_TADV
#define E1000_82542_TSPMT E1000_TSPMT
#define E1000_82542_CRCERRS E1000_CRCERRS
#define E1000_82542_ALGNERRC E1000_ALGNERRC
#define E1000_82542_SYMERRS E1000_SYMERRS
#define E1000_82542_RXERRC E1000_RXERRC
#define E1000_82542_MPC E1000_MPC
#define E1000_82542_SCC E1000_SCC
#define E1000_82542_ECOL E1000_ECOL
#define E1000_82542_MCC E1000_MCC
#define E1000_82542_LATECOL E1000_LATECOL
#define E1000_82542_COLC E1000_COLC
#define E1000_82542_DC E1000_DC
#define E1000_82542_TNCRS E1000_TNCRS
#define E1000_82542_SEC E1000_SEC
#define E1000_82542_CEXTERR E1000_CEXTERR
#define E1000_82542_RLEC E1000_RLEC
#define E1000_82542_XONRXC E1000_XONRXC
#define E1000_82542_XONTXC E1000_XONTXC
#define E1000_82542_XOFFRXC E1000_XOFFRXC
#define E1000_82542_XOFFTXC E1000_XOFFTXC
#define E1000_82542_FCRUC E1000_FCRUC
#define E1000_82542_PRC64 E1000_PRC64
#define E1000_82542_PRC127 E1000_PRC127
#define E1000_82542_PRC255 E1000_PRC255
#define E1000_82542_PRC511 E1000_PRC511
#define E1000_82542_PRC1023 E1000_PRC1023
#define E1000_82542_PRC1522 E1000_PRC1522
#define E1000_82542_GPRC E1000_GPRC
#define E1000_82542_BPRC E1000_BPRC
#define E1000_82542_MPRC E1000_MPRC
#define E1000_82542_GPTC E1000_GPTC
#define E1000_82542_GORCL E1000_GORCL
#define E1000_82542_GORCH E1000_GORCH
#define E1000_82542_GOTCL E1000_GOTCL
#define E1000_82542_GOTCH E1000_GOTCH
#define E1000_82542_RNBC E1000_RNBC
#define E1000_82542_RUC E1000_RUC
#define E1000_82542_RFC E1000_RFC
#define E1000_82542_ROC E1000_ROC
#define E1000_82542_RJC E1000_RJC
#define E1000_82542_MGTPRC E1000_MGTPRC
#define E1000_82542_MGTPDC E1000_MGTPDC
#define E1000_82542_MGTPTC E1000_MGTPTC
#define E1000_82542_TORL E1000_TORL
#define E1000_82542_TORH E1000_TORH
#define E1000_82542_TOTL E1000_TOTL
#define E1000_82542_TOTH E1000_TOTH
#define E1000_82542_TPR E1000_TPR
#define E1000_82542_TPT E1000_TPT
#define E1000_82542_PTC64 E1000_PTC64
#define E1000_82542_PTC127 E1000_PTC127
#define E1000_82542_PTC255 E1000_PTC255
#define E1000_82542_PTC511 E1000_PTC511
#define E1000_82542_PTC1023 E1000_PTC1023
#define E1000_82542_PTC1522 E1000_PTC1522
#define E1000_82542_MPTC E1000_MPTC
#define E1000_82542_BPTC E1000_BPTC
#define E1000_82542_TSCTC E1000_TSCTC
#define E1000_82542_TSCTFC E1000_TSCTFC
#define E1000_82542_RXCSUM E1000_RXCSUM
#define E1000_82542_WUC E1000_WUC
#define E1000_82542_WUFC E1000_WUFC
#define E1000_82542_WUS E1000_WUS
#define E1000_82542_MANC E1000_MANC
#define E1000_82542_IPAV E1000_IPAV
#define E1000_82542_IP4AT E1000_IP4AT
#define E1000_82542_IP6AT E1000_IP6AT
#define E1000_82542_WUPL E1000_WUPL
#define E1000_82542_WUPM E1000_WUPM
#define E1000_82542_FFLT E1000_FFLT
#define E1000_82542_FFMT E1000_FFMT
#define E1000_82542_FFVT E1000_FFVT
struct e1000_eeprom_info {
e1000_eeprom_type type;
uint16_t word_size;
uint16_t opcode_bits;
uint16_t address_bits;
uint16_t delay_usec;
uint16_t page_size;
bool use_eerd;
bool use_eewr;
};
#define E1000_EEPROM_SWDPIN0 0x0001 /* SWDPIN 0 EEPROM Value */
#define E1000_EEPROM_LED_LOGIC 0x0020 /* Led Logic Word */
#define E1000_EEPROM_RW_REG_DATA 16 /* Offset to data in EEPROM
read/write registers */
#define E1000_EEPROM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */
#define E1000_EEPROM_RW_REG_START 1 /* First bit for telling part to start
operation */
#define E1000_EEPROM_RW_ADDR_SHIFT 2 /* Shift to the address bits */
#define E1000_EEPROM_POLL_WRITE 1 /* Flag for polling for write
complete */
#define E1000_EEPROM_POLL_READ 0 /* Flag for polling for read complete */
#define EEPROM_RESERVED_WORD 0xFFFF
/* Register Bit Masks */
/* Device Control */
#define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */
#define E1000_CTRL_BEM 0x00000002 /* Endian Mode.0=little,1=big */
#define E1000_CTRL_PRIOR 0x00000004 /* Priority on PCI. 0=rx,1=fair */
#define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */
#define E1000_CTRL_TME 0x00000010 /* Test mode. 0=normal,1=test */
#define E1000_CTRL_SLE 0x00000020 /* Serial Link on 0=dis,1=en */
#define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */
#define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */
#define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */
#define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */
#define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */
#define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */
#define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */
#define E1000_CTRL_BEM32 0x00000400 /* Big Endian 32 mode */
#define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */
#define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */
#define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */
#define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */
#define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */
#define E1000_CTRL_SWDPIN3 0x00200000 /* SWDPIN 3 value */
#define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */
#define E1000_CTRL_SWDPIO1 0x00800000 /* SWDPIN 1 input or output */
#define E1000_CTRL_SWDPIO2 0x01000000 /* SWDPIN 2 input or output */
#define E1000_CTRL_SWDPIO3 0x02000000 /* SWDPIN 3 input or output */
#define E1000_CTRL_RST 0x04000000 /* Global reset */
#define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */
#define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */
#define E1000_CTRL_RTE 0x20000000 /* Routing tag enable */
#define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */
#define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */
/* Device Status */
#define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */
#define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */
#define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */
#define E1000_STATUS_FUNC_0 0x00000000 /* Function 0 */
#define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */
#define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */
#define E1000_STATUS_TBIMODE 0x00000020 /* TBI mode */
#define E1000_STATUS_SPEED_MASK 0x000000C0
#define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */
#define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */
#define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */
#define E1000_STATUS_ASDV 0x00000300 /* Auto speed detect value */
#define E1000_STATUS_MTXCKOK 0x00000400 /* MTX clock running OK */
#define E1000_STATUS_PCI66 0x00000800 /* In 66Mhz slot */
#define E1000_STATUS_BUS64 0x00001000 /* In 64 bit slot */
#define E1000_STATUS_PCIX_MODE 0x00002000 /* PCI-X mode */
#define E1000_STATUS_PCIX_SPEED 0x0000C000 /* PCI-X bus speed */
#define E1000_STATUS_PF_RST_DONE 0x00200000 /* PCI-X bus speed */
/* Constants used to intrepret the masked PCI-X bus speed. */
#define E1000_STATUS_PCIX_SPEED_66 0x00000000 /* PCI-X bus speed 50-66 MHz */
#define E1000_STATUS_PCIX_SPEED_100 0x00004000 /* PCI-X bus speed 66-100 MHz */
#define E1000_STATUS_PCIX_SPEED_133 0x00008000 /* PCI-X bus speed 100-133 MHz */
/* EEPROM/Flash Control */
#define E1000_EECD_SK 0x00000001 /* EEPROM Clock */
#define E1000_EECD_CS 0x00000002 /* EEPROM Chip Select */
#define E1000_EECD_DI 0x00000004 /* EEPROM Data In */
#define E1000_EECD_DO 0x00000008 /* EEPROM Data Out */
#define E1000_EECD_FWE_MASK 0x00000030
#define E1000_EECD_FWE_DIS 0x00000010 /* Disable FLASH writes */
#define E1000_EECD_FWE_EN 0x00000020 /* Enable FLASH writes */
#define E1000_EECD_FWE_SHIFT 4
#define E1000_EECD_SIZE 0x00000200 /* EEPROM Size (0=64 word 1=256 word) */
#define E1000_EECD_REQ 0x00000040 /* EEPROM Access Request */
#define E1000_EECD_GNT 0x00000080 /* EEPROM Access Grant */
#define E1000_EECD_PRES 0x00000100 /* EEPROM Present */
#define E1000_EECD_ADDR_BITS 0x00000400 /* EEPROM Addressing bits based on type
* (0-small, 1-large) */
#define E1000_EECD_TYPE 0x00002000 /* EEPROM Type (1-SPI, 0-Microwire) */
#ifndef E1000_EEPROM_GRANT_ATTEMPTS
#define E1000_EEPROM_GRANT_ATTEMPTS 1000 /* EEPROM # attempts to gain grant */
#endif
#define E1000_EECD_AUTO_RD 0x00000200 /* EEPROM Auto Read done */
#define E1000_EECD_SIZE_EX_MASK 0x00007800 /* EEprom Size */
#define E1000_EECD_SIZE_EX_SHIFT 11
#define E1000_EECD_NVADDS 0x00018000 /* NVM Address Size */
#define E1000_EECD_SELSHAD 0x00020000 /* Select Shadow RAM */
#define E1000_EECD_INITSRAM 0x00040000 /* Initialize Shadow RAM */
#define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */
#define E1000_EECD_AUPDEN 0x00100000 /* Enable Autonomous FLASH update */
#define E1000_EECD_SHADV 0x00200000 /* Shadow RAM Data Valid */
#define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */
#define E1000_EECD_SECVAL_SHIFT 22
#define E1000_STM_OPCODE 0xDB00
#define E1000_HICR_FW_RESET 0xC0
#define E1000_SHADOW_RAM_WORDS 2048
#define E1000_ICH_NVM_SIG_WORD 0x13
#define E1000_ICH_NVM_SIG_MASK 0xC0
/* EEPROM Read */
#define E1000_EERD_START 0x00000001 /* Start Read */
#define E1000_EERD_DONE 0x00000010 /* Read Done */
#define E1000_EERD_ADDR_SHIFT 8
#define E1000_EERD_ADDR_MASK 0x0000FF00 /* Read Address */
#define E1000_EERD_DATA_SHIFT 16
#define E1000_EERD_DATA_MASK 0xFFFF0000 /* Read Data */
/* EEPROM Commands - Microwire */
#define EEPROM_READ_OPCODE_MICROWIRE 0x6 /* EEPROM read opcode */
#define EEPROM_WRITE_OPCODE_MICROWIRE 0x5 /* EEPROM write opcode */
#define EEPROM_ERASE_OPCODE_MICROWIRE 0x7 /* EEPROM erase opcode */
#define EEPROM_EWEN_OPCODE_MICROWIRE 0x13 /* EEPROM erase/write enable */
#define EEPROM_EWDS_OPCODE_MICROWIRE 0x10 /* EEPROM erast/write disable */
/* EEPROM Commands - SPI */
#define EEPROM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */
#define EEPROM_READ_OPCODE_SPI 0x03 /* EEPROM read opcode */
#define EEPROM_WRITE_OPCODE_SPI 0x02 /* EEPROM write opcode */
#define EEPROM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */
#define EEPROM_WREN_OPCODE_SPI 0x06 /* EEPROM set Write Enable latch */
#define EEPROM_WRDI_OPCODE_SPI 0x04 /* EEPROM reset Write Enable latch */
#define EEPROM_RDSR_OPCODE_SPI 0x05 /* EEPROM read Status register */
#define EEPROM_WRSR_OPCODE_SPI 0x01 /* EEPROM write Status register */
#define EEPROM_ERASE4K_OPCODE_SPI 0x20 /* EEPROM ERASE 4KB */
#define EEPROM_ERASE64K_OPCODE_SPI 0xD8 /* EEPROM ERASE 64KB */
#define EEPROM_ERASE256_OPCODE_SPI 0xDB /* EEPROM ERASE 256B */
/* EEPROM Size definitions */
#define EEPROM_WORD_SIZE_SHIFT 6
#define EEPROM_SIZE_SHIFT 10
#define EEPROM_SIZE_MASK 0x1C00
/* EEPROM Word Offsets */
#define EEPROM_COMPAT 0x0003
#define EEPROM_ID_LED_SETTINGS 0x0004
#define EEPROM_VERSION 0x0005
#define EEPROM_SERDES_AMPLITUDE 0x0006 /* For SERDES output amplitude
adjustment. */
#define EEPROM_PHY_CLASS_WORD 0x0007
#define EEPROM_INIT_CONTROL1_REG 0x000A
#define EEPROM_INIT_CONTROL2_REG 0x000F
#define EEPROM_SWDEF_PINS_CTRL_PORT_1 0x0010
#define EEPROM_INIT_CONTROL3_PORT_B 0x0014
#define EEPROM_INIT_3GIO_3 0x001A
#define EEPROM_SWDEF_PINS_CTRL_PORT_0 0x0020
#define EEPROM_INIT_CONTROL3_PORT_A 0x0024
#define EEPROM_CFG 0x0012
#define EEPROM_FLASH_VERSION 0x0032
#define EEPROM_CHECKSUM_REG 0x003F
#define E1000_EEPROM_CFG_DONE 0x00040000 /* MNG config cycle done */
#define E1000_EEPROM_CFG_DONE_PORT_1 0x00080000 /* ...for second port */
/* Extended Device Control */
#define E1000_CTRL_EXT_GPI0_EN 0x00000001 /* Maps SDP4 to GPI0 */
#define E1000_CTRL_EXT_GPI1_EN 0x00000002 /* Maps SDP5 to GPI1 */
#define E1000_CTRL_EXT_PHYINT_EN E1000_CTRL_EXT_GPI1_EN
#define E1000_CTRL_EXT_GPI2_EN 0x00000004 /* Maps SDP6 to GPI2 */
#define E1000_CTRL_EXT_GPI3_EN 0x00000008 /* Maps SDP7 to GPI3 */
#define E1000_CTRL_EXT_SDP4_DATA 0x00000010 /* Value of SW Defineable
Pin 4 */
#define E1000_CTRL_EXT_SDP5_DATA 0x00000020 /* Value of SW Defineable
Pin 5 */
#define E1000_CTRL_EXT_PHY_INT E1000_CTRL_EXT_SDP5_DATA
#define E1000_CTRL_EXT_SDP6_DATA 0x00000040 /* Value of SW Defineable Pin 6 */
#define E1000_CTRL_EXT_SWDPIN6 0x00000040 /* SWDPIN 6 value */
#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Defineable Pin 7 */
#define E1000_CTRL_EXT_SWDPIN7 0x00000080 /* SWDPIN 7 value */
#define E1000_CTRL_EXT_SDP4_DIR 0x00000100 /* Direction of SDP4 0=in 1=out */
#define E1000_CTRL_EXT_SDP5_DIR 0x00000200 /* Direction of SDP5 0=in 1=out */
#define E1000_CTRL_EXT_SDP6_DIR 0x00000400 /* Direction of SDP6 0=in 1=out */
#define E1000_CTRL_EXT_SWDPIO6 0x00000400 /* SWDPIN 6 Input or output */
#define E1000_CTRL_EXT_SDP7_DIR 0x00000800 /* Direction of SDP7 0=in 1=out */
#define E1000_CTRL_EXT_SWDPIO7 0x00000800 /* SWDPIN 7 Input or output */
#define E1000_CTRL_EXT_ASDCHK 0x00001000 /* Initiate an ASD sequence */
#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
#define E1000_CTRL_EXT_IPS 0x00004000 /* Invert Power State */
#define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */
#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */
#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
#define E1000_CTRL_EXT_LINK_MODE_GMII 0x00000000
#define E1000_CTRL_EXT_LINK_MODE_TBI 0x00C00000
#define E1000_CTRL_EXT_WR_WMARK_MASK 0x03000000
#define E1000_CTRL_EXT_WR_WMARK_256 0x00000000
#define E1000_CTRL_EXT_WR_WMARK_320 0x01000000
#define E1000_CTRL_EXT_WR_WMARK_384 0x02000000
#define E1000_CTRL_EXT_WR_WMARK_448 0x03000000
/* MDI Control */
#define E1000_MDIC_DATA_MASK 0x0000FFFF
#define E1000_MDIC_REG_MASK 0x001F0000
#define E1000_MDIC_REG_SHIFT 16
#define E1000_MDIC_PHY_MASK 0x03E00000
#define E1000_MDIC_PHY_SHIFT 21
#define E1000_MDIC_OP_WRITE 0x04000000
#define E1000_MDIC_OP_READ 0x08000000
#define E1000_MDIC_READY 0x10000000
#define E1000_MDIC_INT_EN 0x20000000
#define E1000_MDIC_ERROR 0x40000000
#define E1000_PHY_CTRL_SPD_EN 0x00000001
#define E1000_PHY_CTRL_D0A_LPLU 0x00000002
#define E1000_PHY_CTRL_NOND0A_LPLU 0x00000004
#define E1000_PHY_CTRL_NOND0A_GBE_DISABLE 0x00000008
#define E1000_PHY_CTRL_GBE_DISABLE 0x00000040
#define E1000_PHY_CTRL_B2B_EN 0x00000080
/* LED Control */
#define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F
#define E1000_LEDCTL_LED0_MODE_SHIFT 0
#define E1000_LEDCTL_LED0_IVRT 0x00000040
#define E1000_LEDCTL_LED0_BLINK 0x00000080
#define E1000_LEDCTL_LED1_MODE_MASK 0x00000F00
#define E1000_LEDCTL_LED1_MODE_SHIFT 8
#define E1000_LEDCTL_LED1_IVRT 0x00004000
#define E1000_LEDCTL_LED1_BLINK 0x00008000
#define E1000_LEDCTL_LED2_MODE_MASK 0x000F0000
#define E1000_LEDCTL_LED2_MODE_SHIFT 16
#define E1000_LEDCTL_LED2_IVRT 0x00400000
#define E1000_LEDCTL_LED2_BLINK 0x00800000
#define E1000_LEDCTL_LED3_MODE_MASK 0x0F000000
#define E1000_LEDCTL_LED3_MODE_SHIFT 24
#define E1000_LEDCTL_LED3_IVRT 0x40000000
#define E1000_LEDCTL_LED3_BLINK 0x80000000
#define E1000_LEDCTL_MODE_LINK_10_1000 0x0
#define E1000_LEDCTL_MODE_LINK_100_1000 0x1
#define E1000_LEDCTL_MODE_LINK_UP 0x2
#define E1000_LEDCTL_MODE_ACTIVITY 0x3
#define E1000_LEDCTL_MODE_LINK_ACTIVITY 0x4
#define E1000_LEDCTL_MODE_LINK_10 0x5
#define E1000_LEDCTL_MODE_LINK_100 0x6
#define E1000_LEDCTL_MODE_LINK_1000 0x7
#define E1000_LEDCTL_MODE_PCIX_MODE 0x8
#define E1000_LEDCTL_MODE_FULL_DUPLEX 0x9
#define E1000_LEDCTL_MODE_COLLISION 0xA
#define E1000_LEDCTL_MODE_BUS_SPEED 0xB
#define E1000_LEDCTL_MODE_BUS_SIZE 0xC
#define E1000_LEDCTL_MODE_PAUSED 0xD
#define E1000_LEDCTL_MODE_LED_ON 0xE
#define E1000_LEDCTL_MODE_LED_OFF 0xF
/* Receive Address */
#define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */
/* Interrupt Cause Read */
#define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */
#define E1000_ICR_TXQE 0x00000002 /* Transmit Queue empty */
#define E1000_ICR_LSC 0x00000004 /* Link Status Change */
#define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */
#define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */
#define E1000_ICR_RXO 0x00000040 /* rx overrun */
#define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */
#define E1000_ICR_MDAC 0x00000200 /* MDIO access complete */
#define E1000_ICR_RXCFG 0x00000400 /* RX /c/ ordered set */
#define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */
#define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */
#define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */
#define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */
#define E1000_ICR_TXD_LOW 0x00008000
#define E1000_ICR_SRPD 0x00010000
/* Interrupt Cause Set */
#define E1000_ICS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
#define E1000_ICS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
#define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
#define E1000_ICS_RXO E1000_ICR_RXO /* rx overrun */
#define E1000_ICS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
#define E1000_ICS_MDAC E1000_ICR_MDAC /* MDIO access complete */
#define E1000_ICS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
#define E1000_ICS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
#define E1000_ICS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
#define E1000_ICS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
#define E1000_ICS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
#define E1000_ICS_TXD_LOW E1000_ICR_TXD_LOW
#define E1000_ICS_SRPD E1000_ICR_SRPD
/* Interrupt Mask Set */
#define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
#define E1000_IMS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
#define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */
#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
#define E1000_IMS_RXO E1000_ICR_RXO /* rx overrun */
#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
#define E1000_IMS_MDAC E1000_ICR_MDAC /* MDIO access complete */
#define E1000_IMS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
#define E1000_IMS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
#define E1000_IMS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
#define E1000_IMS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
#define E1000_IMS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
#define E1000_IMS_TXD_LOW E1000_ICR_TXD_LOW
#define E1000_IMS_SRPD E1000_ICR_SRPD
/* Interrupt Mask Clear */
#define E1000_IMC_TXDW E1000_ICR_TXDW /* Transmit desc written back */
#define E1000_IMC_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
#define E1000_IMC_LSC E1000_ICR_LSC /* Link Status Change */
#define E1000_IMC_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
#define E1000_IMC_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
#define E1000_IMC_RXO E1000_ICR_RXO /* rx overrun */
#define E1000_IMC_RXT0 E1000_ICR_RXT0 /* rx timer intr */
#define E1000_IMC_MDAC E1000_ICR_MDAC /* MDIO access complete */
#define E1000_IMC_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
#define E1000_IMC_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
#define E1000_IMC_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
#define E1000_IMC_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
#define E1000_IMC_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
#define E1000_IMC_TXD_LOW E1000_ICR_TXD_LOW
#define E1000_IMC_SRPD E1000_ICR_SRPD
/* Receive Control */
#define E1000_RCTL_RST 0x00000001 /* Software reset */
#define E1000_RCTL_EN 0x00000002 /* enable */
#define E1000_RCTL_SBP 0x00000004 /* store bad packet */
#define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */
#define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */
#define E1000_RCTL_LPE 0x00000020 /* long packet enable */
#define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */
#define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */
#define E1000_RCTL_LBM_SLP 0x00000080 /* serial link loopback mode */
#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
#define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */
#define E1000_RCTL_RDMTS_QUAT 0x00000100 /* rx desc min threshold size */
#define E1000_RCTL_RDMTS_EIGTH 0x00000200 /* rx desc min threshold size */
#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
#define E1000_RCTL_MO_0 0x00000000 /* multicast offset 11:0 */
#define E1000_RCTL_MO_1 0x00001000 /* multicast offset 12:1 */
#define E1000_RCTL_MO_2 0x00002000 /* multicast offset 13:2 */
#define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */
#define E1000_RCTL_MDR 0x00004000 /* multicast desc ring 0 */
#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
/* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */
#define E1000_RCTL_SZ_2048 0x00000000 /* rx buffer size 2048 */
#define E1000_RCTL_SZ_1024 0x00010000 /* rx buffer size 1024 */
#define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */
#define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */
/* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */
#define E1000_RCTL_SZ_16384 0x00010000 /* rx buffer size 16384 */
#define E1000_RCTL_SZ_8192 0x00020000 /* rx buffer size 8192 */
#define E1000_RCTL_SZ_4096 0x00030000 /* rx buffer size 4096 */
#define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */
#define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */
#define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */
#define E1000_RCTL_DPF 0x00400000 /* discard pause frames */
#define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */
#define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */
/* SW_W_SYNC definitions */
#define E1000_SWFW_EEP_SM 0x0001
#define E1000_SWFW_PHY0_SM 0x0002
#define E1000_SWFW_PHY1_SM 0x0004
#define E1000_SWFW_MAC_CSR_SM 0x0008
/* Receive Descriptor */
#define E1000_RDT_DELAY 0x0000ffff /* Delay timer (1=1024us) */
#define E1000_RDT_FPDB 0x80000000 /* Flush descriptor block */
#define E1000_RDLEN_LEN 0x0007ff80 /* descriptor length */
#define E1000_RDH_RDH 0x0000ffff /* receive descriptor head */
#define E1000_RDT_RDT 0x0000ffff /* receive descriptor tail */
/* Flow Control */
#define E1000_FCRTH_RTH 0x0000FFF8 /* Mask Bits[15:3] for RTH */
#define E1000_FCRTH_XFCE 0x80000000 /* External Flow Control Enable */
#define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */
#define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */
/* Receive Descriptor Control */
#define E1000_RXDCTL_PTHRESH 0x0000003F /* RXDCTL Prefetch Threshold */
#define E1000_RXDCTL_HTHRESH 0x00003F00 /* RXDCTL Host Threshold */
#define E1000_RXDCTL_WTHRESH 0x003F0000 /* RXDCTL Writeback Threshold */
#define E1000_RXDCTL_GRAN 0x01000000 /* RXDCTL Granularity */
#define E1000_RXDCTL_FULL_RX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */
/* Transmit Descriptor Control */
#define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */
#define E1000_TXDCTL_HTHRESH 0x00003F00 /* TXDCTL Host Threshold */
#define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */
#define E1000_TXDCTL_GRAN 0x01000000 /* TXDCTL Granularity */
#define E1000_TXDCTL_LWTHRESH 0xFE000000 /* TXDCTL Low Threshold */
#define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */
#define E1000_TXDCTL_COUNT_DESC 0x00400000 /* Enable the counting of desc.
still to be processed. */
/* Transmit Configuration Word */
#define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */
#define E1000_TXCW_HD 0x00000040 /* TXCW half duplex */
#define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */
#define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */
#define E1000_TXCW_PAUSE_MASK 0x00000180 /* TXCW pause request mask */
#define E1000_TXCW_RF 0x00003000 /* TXCW remote fault */
#define E1000_TXCW_NP 0x00008000 /* TXCW next page */
#define E1000_TXCW_CW 0x0000ffff /* TxConfigWord mask */
#define E1000_TXCW_TXC 0x40000000 /* Transmit Config control */
#define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */
/* Receive Configuration Word */
#define E1000_RXCW_CW 0x0000ffff /* RxConfigWord mask */
#define E1000_RXCW_NC 0x04000000 /* Receive config no carrier */
#define E1000_RXCW_IV 0x08000000 /* Receive config invalid */
#define E1000_RXCW_CC 0x10000000 /* Receive config change */
#define E1000_RXCW_C 0x20000000 /* Receive config */
#define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */
#define E1000_RXCW_ANC 0x80000000 /* Auto-neg complete */
/* Transmit Control */
#define E1000_TCTL_RST 0x00000001 /* software reset */
#define E1000_TCTL_EN 0x00000002 /* enable tx */
#define E1000_TCTL_BCE 0x00000004 /* busy check enable */
#define E1000_TCTL_PSP 0x00000008 /* pad short packets */
#define E1000_TCTL_CT 0x00000ff0 /* collision threshold */
#define E1000_TCTL_COLD 0x003ff000 /* collision distance */
#define E1000_TCTL_SWXOFF 0x00400000 /* SW Xoff transmission */
#define E1000_TCTL_PBE 0x00800000 /* Packet Burst Enable */
#define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */
#define E1000_TCTL_NRTU 0x02000000 /* No Re-transmit on underrun */
#define E1000_TCTL_MULR 0x10000000 /* Multiple request support */
/* Receive Checksum Control */
#define E1000_RXCSUM_PCSS_MASK 0x000000FF /* Packet Checksum Start */
#define E1000_RXCSUM_IPOFL 0x00000100 /* IPv4 checksum offload */
#define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */
#define E1000_RXCSUM_IPV6OFL 0x00000400 /* IPv6 checksum offload */
/* Definitions for power management and wakeup registers */
/* Wake Up Control */
#define E1000_WUC_APME 0x00000001 /* APM Enable */
#define E1000_WUC_PME_EN 0x00000002 /* PME Enable */
#define E1000_WUC_PME_STATUS 0x00000004 /* PME Status */
#define E1000_WUC_APMPME 0x00000008 /* Assert PME on APM Wakeup */
/* Wake Up Filter Control */
#define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
#define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */
#define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */
#define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */
#define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */
#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */
#define E1000_WUFC_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Enable */
#define E1000_WUFC_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Enable */
#define E1000_WUFC_FLX0 0x00010000 /* Flexible Filter 0 Enable */
#define E1000_WUFC_FLX1 0x00020000 /* Flexible Filter 1 Enable */
#define E1000_WUFC_FLX2 0x00040000 /* Flexible Filter 2 Enable */
#define E1000_WUFC_FLX3 0x00080000 /* Flexible Filter 3 Enable */
#define E1000_WUFC_ALL_FILTERS 0x000F00FF /* Mask for all wakeup filters */
#define E1000_WUFC_FLX_OFFSET 16 /* Offset to the Flexible Filters bits */
#define E1000_WUFC_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */
/* Wake Up Status */
#define E1000_WUS_LNKC 0x00000001 /* Link Status Changed */
#define E1000_WUS_MAG 0x00000002 /* Magic Packet Received */
#define E1000_WUS_EX 0x00000004 /* Directed Exact Received */
#define E1000_WUS_MC 0x00000008 /* Directed Multicast Received */
#define E1000_WUS_BC 0x00000010 /* Broadcast Received */
#define E1000_WUS_ARP 0x00000020 /* ARP Request Packet Received */
#define E1000_WUS_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Received */
#define E1000_WUS_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Received */
#define E1000_WUS_FLX0 0x00010000 /* Flexible Filter 0 Match */
#define E1000_WUS_FLX1 0x00020000 /* Flexible Filter 1 Match */
#define E1000_WUS_FLX2 0x00040000 /* Flexible Filter 2 Match */
#define E1000_WUS_FLX3 0x00080000 /* Flexible Filter 3 Match */
#define E1000_WUS_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */
/* Management Control */
#define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */
#define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */
#define E1000_MANC_R_ON_FORCE 0x00000004 /* Reset on Force TCO - RO */
#define E1000_MANC_RMCP_EN 0x00000100 /* Enable RCMP 026Fh Filtering */
#define E1000_MANC_0298_EN 0x00000200 /* Enable RCMP 0298h Filtering */
#define E1000_MANC_IPV4_EN 0x00000400 /* Enable IPv4 */
#define E1000_MANC_IPV6_EN 0x00000800 /* Enable IPv6 */
#define E1000_MANC_SNAP_EN 0x00001000 /* Accept LLC/SNAP */
#define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */
#define E1000_MANC_NEIGHBOR_EN 0x00004000 /* Enable Neighbor Discovery
* Filtering */
#define E1000_MANC_TCO_RESET 0x00010000 /* TCO Reset Occurred */
#define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */
#define E1000_MANC_REPORT_STATUS 0x00040000 /* Status Reporting Enabled */
#define E1000_MANC_SMB_REQ 0x01000000 /* SMBus Request */
#define E1000_MANC_SMB_GNT 0x02000000 /* SMBus Grant */
#define E1000_MANC_SMB_CLK_IN 0x04000000 /* SMBus Clock In */
#define E1000_MANC_SMB_DATA_IN 0x08000000 /* SMBus Data In */
#define E1000_MANC_SMB_DATA_OUT 0x10000000 /* SMBus Data Out */
#define E1000_MANC_SMB_CLK_OUT 0x20000000 /* SMBus Clock Out */
#define E1000_MANC_SMB_DATA_OUT_SHIFT 28 /* SMBus Data Out Shift */
#define E1000_MANC_SMB_CLK_OUT_SHIFT 29 /* SMBus Clock Out Shift */
/* Wake Up Packet Length */
#define E1000_WUPL_LENGTH_MASK 0x0FFF /* Only the lower 12 bits are valid */
#define E1000_MDALIGN 4096
/* EEPROM Commands */
#define EEPROM_READ_OPCODE 0x6 /* EERPOM read opcode */
#define EEPROM_WRITE_OPCODE 0x5 /* EERPOM write opcode */
#define EEPROM_ERASE_OPCODE 0x7 /* EERPOM erase opcode */
#define EEPROM_EWEN_OPCODE 0x13 /* EERPOM erase/write enable */
#define EEPROM_EWDS_OPCODE 0x10 /* EERPOM erast/write disable */
/* Word definitions for ID LED Settings */
#define ID_LED_RESERVED_0000 0x0000
#define ID_LED_RESERVED_FFFF 0xFFFF
#define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \
(ID_LED_OFF1_OFF2 << 8) | \
(ID_LED_DEF1_DEF2 << 4) | \
(ID_LED_DEF1_DEF2))
#define ID_LED_DEF1_DEF2 0x1
#define ID_LED_DEF1_ON2 0x2
#define ID_LED_DEF1_OFF2 0x3
#define ID_LED_ON1_DEF2 0x4
#define ID_LED_ON1_ON2 0x5
#define ID_LED_ON1_OFF2 0x6
#define ID_LED_OFF1_DEF2 0x7
#define ID_LED_OFF1_ON2 0x8
#define ID_LED_OFF1_OFF2 0x9
/* Mask bits for fields in Word 0x03 of the EEPROM */
#define EEPROM_COMPAT_SERVER 0x0400
#define EEPROM_COMPAT_CLIENT 0x0200
/* Mask bits for fields in Word 0x0a of the EEPROM */
#define EEPROM_WORD0A_ILOS 0x0010
#define EEPROM_WORD0A_SWDPIO 0x01E0
#define EEPROM_WORD0A_LRST 0x0200
#define EEPROM_WORD0A_FD 0x0400
#define EEPROM_WORD0A_66MHZ 0x0800
/* Mask bits for fields in Word 0x0f of the EEPROM */
#define EEPROM_WORD0F_PAUSE_MASK 0x3000
#define EEPROM_WORD0F_PAUSE 0x1000
#define EEPROM_WORD0F_ASM_DIR 0x2000
#define EEPROM_WORD0F_ANE 0x0800
#define EEPROM_WORD0F_SWPDIO_EXT 0x00F0
/* For checksumming, the sum of all words in the EEPROM should equal 0xBABA. */
#define EEPROM_SUM 0xBABA
/* EEPROM Map defines (WORD OFFSETS)*/
#define EEPROM_NODE_ADDRESS_BYTE_0 0
#define EEPROM_PBA_BYTE_1 8
/* EEPROM Map Sizes (Byte Counts) */
#define PBA_SIZE 4
/* Collision related configuration parameters */
#define E1000_COLLISION_THRESHOLD 0xF
#define E1000_CT_SHIFT 4
#define E1000_COLLISION_DISTANCE 63
#define E1000_COLLISION_DISTANCE_82542 64
#define E1000_FDX_COLLISION_DISTANCE E1000_COLLISION_DISTANCE
#define E1000_HDX_COLLISION_DISTANCE E1000_COLLISION_DISTANCE
#define E1000_GB_HDX_COLLISION_DISTANCE 512
#define E1000_COLD_SHIFT 12
/* The number of Transmit and Receive Descriptors must be a multiple of 8 */
#define REQ_TX_DESCRIPTOR_MULTIPLE 8
#define REQ_RX_DESCRIPTOR_MULTIPLE 8
/* Default values for the transmit IPG register */
#define DEFAULT_82542_TIPG_IPGT 10
#define DEFAULT_82543_TIPG_IPGT_FIBER 9
#define DEFAULT_82543_TIPG_IPGT_COPPER 8
#define E1000_TIPG_IPGT_MASK 0x000003FF
#define E1000_TIPG_IPGR1_MASK 0x000FFC00
#define E1000_TIPG_IPGR2_MASK 0x3FF00000
#define DEFAULT_82542_TIPG_IPGR1 2
#define DEFAULT_82543_TIPG_IPGR1 8
#define E1000_TIPG_IPGR1_SHIFT 10
#define DEFAULT_82542_TIPG_IPGR2 10
#define DEFAULT_82543_TIPG_IPGR2 6
#define DEFAULT_80003ES2LAN_TIPG_IPGR2 7
#define E1000_TIPG_IPGR2_SHIFT 20
#define E1000_TXDMAC_DPP 0x00000001
/* Adaptive IFS defines */
#define TX_THRESHOLD_START 8
#define TX_THRESHOLD_INCREMENT 10
#define TX_THRESHOLD_DECREMENT 1
#define TX_THRESHOLD_STOP 190
#define TX_THRESHOLD_DISABLE 0
#define TX_THRESHOLD_TIMER_MS 10000
#define MIN_NUM_XMITS 1000
#define IFS_MAX 80
#define IFS_STEP 10
#define IFS_MIN 40
#define IFS_RATIO 4
/* PBA constants */
#define E1000_PBA_16K 0x0010 /* 16KB, default TX allocation */
#define E1000_PBA_24K 0x0018
#define E1000_PBA_38K 0x0026
#define E1000_PBA_40K 0x0028
#define E1000_PBA_48K 0x0030 /* 48KB, default RX allocation */
/* Flow Control Constants */
#define FLOW_CONTROL_ADDRESS_LOW 0x00C28001
#define FLOW_CONTROL_ADDRESS_HIGH 0x00000100
#define FLOW_CONTROL_TYPE 0x8808
/* The historical defaults for the flow control values are given below. */
#define FC_DEFAULT_HI_THRESH (0x8000) /* 32KB */
#define FC_DEFAULT_LO_THRESH (0x4000) /* 16KB */
#define FC_DEFAULT_TX_TIMER (0x100) /* ~130 us */
/* Flow Control High-Watermark: 43464 bytes */
#define E1000_FC_HIGH_THRESH 0xA9C8
/* Flow Control Low-Watermark: 43456 bytes */
#define E1000_FC_LOW_THRESH 0xA9C0
/* Flow Control Pause Time: 858 usec */
#define E1000_FC_PAUSE_TIME 0x0680
/* The number of bits that we need to shift right to move the "pause"
* bits from the EEPROM (bits 13:12) to the "pause" (bits 8:7) field
* in the TXCW register
*/
#define PAUSE_SHIFT 5
/* The number of bits that we need to shift left to move the "SWDPIO"
* bits from the EEPROM (bits 8:5) to the "SWDPIO" (bits 25:22) field
* in the CTRL register
*/
#define SWDPIO_SHIFT 17
/* The number of bits that we need to shift left to move the "SWDPIO_EXT"
* bits from the EEPROM word F (bits 7:4) to the bits 11:8 of The
* Extended CTRL register.
* in the CTRL register
*/
#define SWDPIO__EXT_SHIFT 4
#define RECEIVE_BUFFER_ALIGN_SIZE (256)
/* The number of milliseconds we wait for auto-negotiation to complete */
#define LINK_UP_TIMEOUT 500
#define E1000_TX_BUFFER_SIZE ((uint32_t)1514)
/* Structures, enums, and macros for the PHY */
/* Bit definitions for the Management Data IO (MDIO) and Management Data
* Clock (MDC) pins in the Device Control Register.
*/
#define E1000_CTRL_PHY_RESET_DIR E1000_CTRL_SWDPIO0
#define E1000_CTRL_PHY_RESET E1000_CTRL_SWDPIN0
#define E1000_CTRL_MDIO_DIR E1000_CTRL_SWDPIO2
#define E1000_CTRL_MDIO E1000_CTRL_SWDPIN2
#define E1000_CTRL_MDC_DIR E1000_CTRL_SWDPIO3
#define E1000_CTRL_MDC E1000_CTRL_SWDPIN3
#define E1000_CTRL_PHY_RESET_DIR4 E1000_CTRL_EXT_SDP4_DIR
#define E1000_CTRL_PHY_RESET4 E1000_CTRL_EXT_SDP4_DATA
/* PHY 1000 MII Register/Bit Definitions */
/* PHY Registers defined by IEEE */
#define PHY_CTRL 0x00 /* Control Register */
#define PHY_STATUS 0x01 /* Status Regiser */
#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */
#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */
#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
#define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */
#define PHY_AUTONEG_EXP 0x06 /* Autoneg Expansion Reg */
#define PHY_NEXT_PAGE_TX 0x07 /* Next Page TX */
#define PHY_LP_NEXT_PAGE 0x08 /* Link Partner Next Page */
#define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */
#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
#define PHY_EXT_STATUS 0x0F /* Extended Status Reg */
/* M88E1000 Specific Registers */
#define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */
#define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */
#define M88E1000_INT_ENABLE 0x12 /* Interrupt Enable Register */
#define M88E1000_INT_STATUS 0x13 /* Interrupt Status Register */
#define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */
#define M88E1000_RX_ERR_CNTR 0x15 /* Receive Error Counter */
#define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */
#define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */
#define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */
/* M88EC018 Rev 2 specific DownShift settings */
#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00
#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_1X 0x0000
#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_2X 0x0200
#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_3X 0x0400
#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_4X 0x0600
#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800
#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_6X 0x0A00
#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_7X 0x0C00
#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_8X 0x0E00
/* IGP01E1000 specifics */
#define IGP01E1000_IEEE_REGS_PAGE 0x0000
#define IGP01E1000_IEEE_RESTART_AUTONEG 0x3300
#define IGP01E1000_IEEE_FORCE_GIGA 0x0140
/* IGP01E1000 Specific Registers */
#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* PHY Specific Port Config Register */
#define IGP01E1000_PHY_PORT_STATUS 0x11 /* PHY Specific Status Register */
#define IGP01E1000_PHY_PORT_CTRL 0x12 /* PHY Specific Control Register */
#define IGP01E1000_PHY_LINK_HEALTH 0x13 /* PHY Link Health Register */
#define IGP01E1000_GMII_FIFO 0x14 /* GMII FIFO Register */
#define IGP01E1000_PHY_CHANNEL_QUALITY 0x15 /* PHY Channel Quality Register */
#define IGP02E1000_PHY_POWER_MGMT 0x19
#define IGP01E1000_PHY_PAGE_SELECT 0x1F /* PHY Page Select Core Register */
/* IGP01E1000 AGC Registers - stores the cable length values*/
#define IGP01E1000_PHY_AGC_A 0x1172
#define IGP01E1000_PHY_AGC_B 0x1272
#define IGP01E1000_PHY_AGC_C 0x1472
#define IGP01E1000_PHY_AGC_D 0x1872
/* IGP01E1000 Specific Port Config Register - R/W */
#define IGP01E1000_PSCFR_AUTO_MDIX_PAR_DETECT 0x0010
#define IGP01E1000_PSCFR_PRE_EN 0x0020
#define IGP01E1000_PSCFR_SMART_SPEED 0x0080
#define IGP01E1000_PSCFR_DISABLE_TPLOOPBACK 0x0100
#define IGP01E1000_PSCFR_DISABLE_JABBER 0x0400
#define IGP01E1000_PSCFR_DISABLE_TRANSMIT 0x2000
/* IGP02E1000 AGC Registers for cable length values */
#define IGP02E1000_PHY_AGC_A 0x11B1
#define IGP02E1000_PHY_AGC_B 0x12B1
#define IGP02E1000_PHY_AGC_C 0x14B1
#define IGP02E1000_PHY_AGC_D 0x18B1
#define IGP02E1000_PM_SPD 0x0001 /* Smart Power Down */
#define IGP02E1000_PM_D3_LPLU 0x0004 /* Enable LPLU in
non-D0a modes */
#define IGP02E1000_PM_D0_LPLU 0x0002 /* Enable LPLU in
D0a mode */
/* IGP01E1000 DSP Reset Register */
#define IGP01E1000_PHY_DSP_RESET 0x1F33
#define IGP01E1000_PHY_DSP_SET 0x1F71
#define IGP01E1000_PHY_DSP_FFE 0x1F35
#define IGP01E1000_PHY_CHANNEL_NUM 4
#define IGP02E1000_PHY_CHANNEL_NUM 4
#define IGP01E1000_PHY_AGC_PARAM_A 0x1171
#define IGP01E1000_PHY_AGC_PARAM_B 0x1271
#define IGP01E1000_PHY_AGC_PARAM_C 0x1471
#define IGP01E1000_PHY_AGC_PARAM_D 0x1871
#define IGP01E1000_PHY_EDAC_MU_INDEX 0xC000
#define IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS 0x8000
#define IGP01E1000_PHY_ANALOG_TX_STATE 0x2890
#define IGP01E1000_PHY_ANALOG_CLASS_A 0x2000
#define IGP01E1000_PHY_FORCE_ANALOG_ENABLE 0x0004
#define IGP01E1000_PHY_DSP_FFE_CM_CP 0x0069
#define IGP01E1000_PHY_DSP_FFE_DEFAULT 0x002A
/* IGP01E1000 PCS Initialization register - stores the polarity status when
* speed = 1000 Mbps. */
#define IGP01E1000_PHY_PCS_INIT_REG 0x00B4
#define IGP01E1000_PHY_PCS_CTRL_REG 0x00B5
#define IGP01E1000_ANALOG_REGS_PAGE 0x20C0
/* IGP01E1000 GMII FIFO Register */
#define IGP01E1000_GMII_FLEX_SPD 0x10 /* Enable flexible speed
* on Link-Up */
#define IGP01E1000_GMII_SPD 0x20 /* Enable SPD */
/* IGP01E1000 Analog Register */
#define IGP01E1000_ANALOG_SPARE_FUSE_STATUS 0x20D1
#define IGP01E1000_ANALOG_FUSE_STATUS 0x20D0
#define IGP01E1000_ANALOG_FUSE_CONTROL 0x20DC
#define IGP01E1000_ANALOG_FUSE_BYPASS 0x20DE
#define IGP01E1000_ANALOG_FUSE_POLY_MASK 0xF000
#define IGP01E1000_ANALOG_FUSE_FINE_MASK 0x0F80
#define IGP01E1000_ANALOG_FUSE_COARSE_MASK 0x0070
#define IGP01E1000_ANALOG_SPARE_FUSE_ENABLED 0x0100
#define IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL 0x0002
#define IGP01E1000_ANALOG_FUSE_COARSE_THRESH 0x0040
#define IGP01E1000_ANALOG_FUSE_COARSE_10 0x0010
#define IGP01E1000_ANALOG_FUSE_FINE_1 0x0080
#define IGP01E1000_ANALOG_FUSE_FINE_10 0x0500
/* IGP01E1000 Specific Port Control Register - R/W */
#define IGP01E1000_PSCR_TP_LOOPBACK 0x0010
#define IGP01E1000_PSCR_CORRECT_NC_SCMBLR 0x0200
#define IGP01E1000_PSCR_TEN_CRS_SELECT 0x0400
#define IGP01E1000_PSCR_FLIP_CHIP 0x0800
#define IGP01E1000_PSCR_AUTO_MDIX 0x1000
#define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0-MDI, 1-MDIX */
/* GG82563 PHY Specific Status Register (Page 0, Register 16 */
#define GG82563_PSCR_DISABLE_JABBER 0x0001 /* 1=Disable Jabber */
#define GG82563_PSCR_POLARITY_REVERSAL_DISABLE 0x0002 /* 1=Polarity Reversal
Disabled */
#define GG82563_PSCR_POWER_DOWN 0x0004 /* 1=Power Down */
#define GG82563_PSCR_COPPER_TRANSMITER_DISABLE 0x0008 /* 1=Transmitter
Disabled */
#define GG82563_PSCR_CROSSOVER_MODE_MASK 0x0060
#define GG82563_PSCR_CROSSOVER_MODE_MDI 0x0000 /* 00=Manual MDI
configuration */
#define GG82563_PSCR_CROSSOVER_MODE_MDIX 0x0020 /* 01=Manual MDIX
configuration */
#define GG82563_PSCR_CROSSOVER_MODE_AUTO 0x0060 /* 11=Automatic
crossover */
#define GG82563_PSCR_ENALBE_EXTENDED_DISTANCE 0x0080 /* 1=Enable Extended
Distance */
#define GG82563_PSCR_ENERGY_DETECT_MASK 0x0300
#define GG82563_PSCR_ENERGY_DETECT_OFF 0x0000 /* 00,01=Off */
#define GG82563_PSCR_ENERGY_DETECT_RX 0x0200 /* 10=Sense on Rx only
(Energy Detect) */
#define GG82563_PSCR_ENERGY_DETECT_RX_TM 0x0300 /* 11=Sense and Tx NLP */
#define GG82563_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force Link Good */
#define GG82563_PSCR_DOWNSHIFT_ENABLE 0x0800 /* 1=Enable Downshift */
#define GG82563_PSCR_DOWNSHIFT_COUNTER_MASK 0x7000
#define GG82563_PSCR_DOWNSHIFT_COUNTER_SHIFT 12
/* PHY Specific Status Register (Page 0, Register 17) */
#define GG82563_PSSR_JABBER 0x0001 /* 1=Jabber */
#define GG82563_PSSR_POLARITY 0x0002 /* 1=Polarity Reversed */
#define GG82563_PSSR_LINK 0x0008 /* 1=Link is Up */
#define GG82563_PSSR_ENERGY_DETECT 0x0010 /* 1=Sleep, 0=Active */
#define GG82563_PSSR_DOWNSHIFT 0x0020 /* 1=Downshift */
#define GG82563_PSSR_CROSSOVER_STATUS 0x0040 /* 1=MDIX, 0=MDI */
#define GG82563_PSSR_RX_PAUSE_ENABLED 0x0100 /* 1=Receive Pause Enabled */
#define GG82563_PSSR_TX_PAUSE_ENABLED 0x0200 /* 1=Transmit Pause Enabled */
#define GG82563_PSSR_LINK_UP 0x0400 /* 1=Link Up */
#define GG82563_PSSR_SPEED_DUPLEX_RESOLVED 0x0800 /* 1=Resolved */
#define GG82563_PSSR_PAGE_RECEIVED 0x1000 /* 1=Page Received */
#define GG82563_PSSR_DUPLEX 0x2000 /* 1-Full-Duplex */
#define GG82563_PSSR_SPEED_MASK 0xC000
#define GG82563_PSSR_SPEED_10MBPS 0x0000 /* 00=10Mbps */
#define GG82563_PSSR_SPEED_100MBPS 0x4000 /* 01=100Mbps */
#define GG82563_PSSR_SPEED_1000MBPS 0x8000 /* 10=1000Mbps */
/* PHY Specific Status Register 2 (Page 0, Register 19) */
#define GG82563_PSSR2_JABBER 0x0001 /* 1=Jabber */
#define GG82563_PSSR2_POLARITY_CHANGED 0x0002 /* 1=Polarity Changed */
#define GG82563_PSSR2_ENERGY_DETECT_CHANGED 0x0010 /* 1=Energy Detect Changed */
#define GG82563_PSSR2_DOWNSHIFT_INTERRUPT 0x0020 /* 1=Downshift Detected */
#define GG82563_PSSR2_MDI_CROSSOVER_CHANGE 0x0040 /* 1=Crossover Changed */
#define GG82563_PSSR2_FALSE_CARRIER 0x0100 /* 1=false Carrier */
#define GG82563_PSSR2_SYMBOL_ERROR 0x0200 /* 1=Symbol Error */
#define GG82563_PSSR2_LINK_STATUS_CHANGED 0x0400 /* 1=Link Status Changed */
#define GG82563_PSSR2_AUTO_NEG_COMPLETED 0x0800 /* 1=Auto-Neg Completed */
#define GG82563_PSSR2_PAGE_RECEIVED 0x1000 /* 1=Page Received */
#define GG82563_PSSR2_DUPLEX_CHANGED 0x2000 /* 1=Duplex Changed */
#define GG82563_PSSR2_SPEED_CHANGED 0x4000 /* 1=Speed Changed */
#define GG82563_PSSR2_AUTO_NEG_ERROR 0x8000 /* 1=Auto-Neg Error */
/* PHY Specific Control Register 2 (Page 0, Register 26) */
#define GG82563_PSCR2_10BT_POLARITY_FORCE 0x0002 /* 1=Force Negative
Polarity */
#define GG82563_PSCR2_1000MB_TEST_SELECT_MASK 0x000C
#define GG82563_PSCR2_1000MB_TEST_SELECT_NORMAL 0x0000 /* 00,01=Normal
Operation */
#define GG82563_PSCR2_1000MB_TEST_SELECT_112NS 0x0008 /* 10=Select 112ns
Sequence */
#define GG82563_PSCR2_1000MB_TEST_SELECT_16NS 0x000C /* 11=Select 16ns
Sequence */
#define GG82563_PSCR2_REVERSE_AUTO_NEG 0x2000 /* 1=Reverse
Auto-Negotiation */
#define GG82563_PSCR2_1000BT_DISABLE 0x4000 /* 1=Disable
1000BASE-T */
#define GG82563_PSCR2_TRANSMITER_TYPE_MASK 0x8000
#define GG82563_PSCR2_TRANSMITTER_TYPE_CLASS_B 0x0000 /* 0=Class B */
#define GG82563_PSCR2_TRANSMITTER_TYPE_CLASS_A 0x8000 /* 1=Class A */
/* MAC Specific Control Register (Page 2, Register 21) */
/* Tx clock speed for Link Down and 1000BASE-T for the following speeds */
#define GG82563_MSCR_TX_CLK_MASK 0x0007
#define GG82563_MSCR_TX_CLK_10MBPS_2_5MHZ 0x0004
#define GG82563_MSCR_TX_CLK_100MBPS_25MHZ 0x0005
#define GG82563_MSCR_TX_CLK_1000MBPS_2_5MHZ 0x0006
#define GG82563_MSCR_TX_CLK_1000MBPS_25MHZ 0x0007
#define GG82563_MSCR_ASSERT_CRS_ON_TX 0x0010 /* 1=Assert */
/* DSP Distance Register (Page 5, Register 26) */
#define GG82563_DSPD_CABLE_LENGTH 0x0007 /* 0 = <50M;
1 = 50-80M;
2 = 80-110M;
3 = 110-140M;
4 = >140M */
/* Kumeran Mode Control Register (Page 193, Register 16) */
#define GG82563_KMCR_PHY_LEDS_EN 0x0020 /* 1=PHY LEDs,
0=Kumeran Inband LEDs */
#define GG82563_KMCR_FORCE_LINK_UP 0x0040 /* 1=Force Link Up */
#define GG82563_KMCR_SUPPRESS_SGMII_EPD_EXT 0x0080
#define GG82563_KMCR_MDIO_BUS_SPEED_SELECT_MASK 0x0400
#define GG82563_KMCR_MDIO_BUS_SPEED_SELECT 0x0400 /* 1=6.25MHz,
0=0.8MHz */
#define GG82563_KMCR_PASS_FALSE_CARRIER 0x0800
/* Power Management Control Register (Page 193, Register 20) */
#define GG82563_PMCR_ENABLE_ELECTRICAL_IDLE 0x0001 /* 1=Enalbe SERDES
Electrical Idle */
#define GG82563_PMCR_DISABLE_PORT 0x0002 /* 1=Disable Port */
#define GG82563_PMCR_DISABLE_SERDES 0x0004 /* 1=Disable SERDES */
#define GG82563_PMCR_REVERSE_AUTO_NEG 0x0008 /* 1=Enable Reverse
Auto-Negotiation */
#define GG82563_PMCR_DISABLE_1000_NON_D0 0x0010 /* 1=Disable 1000Mbps
Auto-Neg in non D0 */
#define GG82563_PMCR_DISABLE_1000 0x0020 /* 1=Disable 1000Mbps
Auto-Neg Always */
#define GG82563_PMCR_REVERSE_AUTO_NEG_D0A 0x0040 /* 1=Enable D0a
Reverse Auto-Negotiation */
#define GG82563_PMCR_FORCE_POWER_STATE 0x0080 /* 1=Force Power State */
#define GG82563_PMCR_PROGRAMMED_POWER_STATE_MASK 0x0300
#define GG82563_PMCR_PROGRAMMED_POWER_STATE_DR 0x0000 /* 00=Dr */
#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D0U 0x0100 /* 01=D0u */
#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D0A 0x0200 /* 10=D0a */
#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D3 0x0300 /* 11=D3 */
/* In-Band Control Register (Page 194, Register 18) */
#define GG82563_ICR_DIS_PADDING 0x0010 /* Disable Padding Use */
/* Bits...
* 15-5: page
* 4-0: register offset
*/
#define GG82563_PAGE_SHIFT 5
#define GG82563_REG(page, reg) \
(((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS))
#define GG82563_MIN_ALT_REG 30
/* GG82563 Specific Registers */
#define GG82563_PHY_SPEC_CTRL \
GG82563_REG(0, 16) /* PHY Specific Control */
#define GG82563_PHY_SPEC_STATUS \
GG82563_REG(0, 17) /* PHY Specific Status */
#define GG82563_PHY_INT_ENABLE \
GG82563_REG(0, 18) /* Interrupt Enable */
#define GG82563_PHY_SPEC_STATUS_2 \
GG82563_REG(0, 19) /* PHY Specific Status 2 */
#define GG82563_PHY_RX_ERR_CNTR \
GG82563_REG(0, 21) /* Receive Error Counter */
#define GG82563_PHY_PAGE_SELECT \
GG82563_REG(0, 22) /* Page Select */
#define GG82563_PHY_SPEC_CTRL_2 \
GG82563_REG(0, 26) /* PHY Specific Control 2 */
#define GG82563_PHY_PAGE_SELECT_ALT \
GG82563_REG(0, 29) /* Alternate Page Select */
#define GG82563_PHY_TEST_CLK_CTRL \
GG82563_REG(0, 30) /* Test Clock Control (use reg. 29 to select) */
#define GG82563_PHY_MAC_SPEC_CTRL \
GG82563_REG(2, 21) /* MAC Specific Control Register */
#define GG82563_PHY_MAC_SPEC_CTRL_2 \
GG82563_REG(2, 26) /* MAC Specific Control 2 */
#define GG82563_PHY_DSP_DISTANCE \
GG82563_REG(5, 26) /* DSP Distance */
/* Page 193 - Port Control Registers */
#define GG82563_PHY_KMRN_MODE_CTRL \
GG82563_REG(193, 16) /* Kumeran Mode Control */
#define GG82563_PHY_PORT_RESET \
GG82563_REG(193, 17) /* Port Reset */
#define GG82563_PHY_REVISION_ID \
GG82563_REG(193, 18) /* Revision ID */
#define GG82563_PHY_DEVICE_ID \
GG82563_REG(193, 19) /* Device ID */
#define GG82563_PHY_PWR_MGMT_CTRL \
GG82563_REG(193, 20) /* Power Management Control */
#define GG82563_PHY_RATE_ADAPT_CTRL \
GG82563_REG(193, 25) /* Rate Adaptation Control */
/* Page 194 - KMRN Registers */
#define GG82563_PHY_KMRN_FIFO_CTRL_STAT \
GG82563_REG(194, 16) /* FIFO's Control/Status */
#define GG82563_PHY_KMRN_CTRL \
GG82563_REG(194, 17) /* Control */
#define GG82563_PHY_INBAND_CTRL \
GG82563_REG(194, 18) /* Inband Control */
#define GG82563_PHY_KMRN_DIAGNOSTIC \
GG82563_REG(194, 19) /* Diagnostic */
#define GG82563_PHY_ACK_TIMEOUTS \
GG82563_REG(194, 20) /* Acknowledge Timeouts */
#define GG82563_PHY_ADV_ABILITY \
GG82563_REG(194, 21) /* Advertised Ability */
#define GG82563_PHY_LINK_PARTNER_ADV_ABILITY \
GG82563_REG(194, 23) /* Link Partner Advertised Ability */
#define GG82563_PHY_ADV_NEXT_PAGE \
GG82563_REG(194, 24) /* Advertised Next Page */
#define GG82563_PHY_LINK_PARTNER_ADV_NEXT_PAGE \
GG82563_REG(194, 25) /* Link Partner Advertised Next page */
#define GG82563_PHY_KMRN_MISC \
GG82563_REG(194, 26) /* Misc. */
/* PHY Control Register */
#define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */
#define MII_CR_COLL_TEST_ENABLE 0x0080 /* Collision test enable */
#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */
#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */
#define MII_CR_ISOLATE 0x0400 /* Isolate PHY from MII */
#define MII_CR_POWER_DOWN 0x0800 /* Power down */
#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */
#define MII_CR_SPEED_SELECT_LSB 0x2000 /* bits 6,13: 10=1000, 01=100, 00=10 */
#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */
#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */
/* PHY Status Register */
#define MII_SR_EXTENDED_CAPS 0x0001 /* Extended register capabilities */
#define MII_SR_JABBER_DETECT 0x0002 /* Jabber Detected */
#define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */
#define MII_SR_AUTONEG_CAPS 0x0008 /* Auto Neg Capable */
#define MII_SR_REMOTE_FAULT 0x0010 /* Remote Fault Detect */
#define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */
#define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */
#define MII_SR_EXTENDED_STATUS 0x0100 /* Ext. status info in Reg 0x0F */
#define MII_SR_100T2_HD_CAPS 0x0200 /* 100T2 Half Duplex Capable */
#define MII_SR_100T2_FD_CAPS 0x0400 /* 100T2 Full Duplex Capable */
#define MII_SR_10T_HD_CAPS 0x0800 /* 10T Half Duplex Capable */
#define MII_SR_10T_FD_CAPS 0x1000 /* 10T Full Duplex Capable */
#define MII_SR_100X_HD_CAPS 0x2000 /* 100X Half Duplex Capable */
#define MII_SR_100X_FD_CAPS 0x4000 /* 100X Full Duplex Capable */
#define MII_SR_100T4_CAPS 0x8000 /* 100T4 Capable */
/* Autoneg Advertisement Register */
#define NWAY_AR_SELECTOR_FIELD 0x0001 /* indicates IEEE 802.3 CSMA/CD */
#define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */
#define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */
#define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */
#define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */
#define NWAY_AR_100T4_CAPS 0x0200 /* 100T4 Capable */
#define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */
#define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */
#define NWAY_AR_REMOTE_FAULT 0x2000 /* Remote Fault detected */
#define NWAY_AR_NEXT_PAGE 0x8000 /* Next Page ability supported */
/* Link Partner Ability Register (Base Page) */
#define NWAY_LPAR_SELECTOR_FIELD 0x0000 /* LP protocol selector field */
#define NWAY_LPAR_10T_HD_CAPS 0x0020 /* LP is 10T Half Duplex Capable */
#define NWAY_LPAR_10T_FD_CAPS 0x0040 /* LP is 10T Full Duplex Capable */
#define NWAY_LPAR_100TX_HD_CAPS 0x0080 /* LP is 100TX Half Duplex Capable */
#define NWAY_LPAR_100TX_FD_CAPS 0x0100 /* LP is 100TX Full Duplex Capable */
#define NWAY_LPAR_100T4_CAPS 0x0200 /* LP is 100T4 Capable */
#define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */
#define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */
#define NWAY_LPAR_REMOTE_FAULT 0x2000 /* LP has detected Remote Fault */
#define NWAY_LPAR_ACKNOWLEDGE 0x4000 /* LP has rx'd link code word */
#define NWAY_LPAR_NEXT_PAGE 0x8000 /* Next Page ability supported */
/* Autoneg Expansion Register */
#define NWAY_ER_LP_NWAY_CAPS 0x0001 /* LP has Auto Neg Capability */
#define NWAY_ER_PAGE_RXD 0x0002 /* LP is 10T Half Duplex Capable */
#define NWAY_ER_NEXT_PAGE_CAPS 0x0004 /* LP is 10T Full Duplex Capable */
#define NWAY_ER_LP_NEXT_PAGE_CAPS 0x0008 /* LP is 100TX Half Duplex Capable */
#define NWAY_ER_PAR_DETECT_FAULT 0x0100 /* LP is 100TX Full Duplex Capable */
/* Next Page TX Register */
#define NPTX_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */
#define NPTX_TOGGLE 0x0800 /* Toggles between exchanges
* of different NP
*/
#define NPTX_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg
* 0 = cannot comply with msg
*/
#define NPTX_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */
#define NPTX_NEXT_PAGE 0x8000 /* 1 = addition NP will follow
* 0 = sending last NP
*/
/* Link Partner Next Page Register */
#define LP_RNPR_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */
#define LP_RNPR_TOGGLE 0x0800 /* Toggles between exchanges
* of different NP
*/
#define LP_RNPR_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg
* 0 = cannot comply with msg
*/
#define LP_RNPR_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */
#define LP_RNPR_ACKNOWLDGE 0x4000 /* 1 = ACK / 0 = NO ACK */
#define LP_RNPR_NEXT_PAGE 0x8000 /* 1 = addition NP will follow
* 0 = sending last NP
*/
/* 1000BASE-T Control Register */
#define CR_1000T_ASYM_PAUSE 0x0080 /* Advertise asymmetric pause bit */
#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */
#define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */
#define CR_1000T_REPEATER_DTE 0x0400 /* 1=Repeater/switch device port */
/* 0=DTE device */
#define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */
/* 0=Configure PHY as Slave */
#define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */
/* 0=Automatic Master/Slave config */
#define CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */
#define CR_1000T_TEST_MODE_1 0x2000 /* Transmit Waveform test */
#define CR_1000T_TEST_MODE_2 0x4000 /* Master Transmit Jitter test */
#define CR_1000T_TEST_MODE_3 0x6000 /* Slave Transmit Jitter test */
#define CR_1000T_TEST_MODE_4 0x8000 /* Transmitter Distortion test */
/* 1000BASE-T Status Register */
#define SR_1000T_IDLE_ERROR_CNT 0x00FF /* Num idle errors since last read */
#define SR_1000T_ASYM_PAUSE_DIR 0x0100 /* LP asymmetric pause direction bit */
#define SR_1000T_LP_HD_CAPS 0x0400 /* LP is 1000T HD capable */
#define SR_1000T_LP_FD_CAPS 0x0800 /* LP is 1000T FD capable */
#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
#define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */
#define SR_1000T_MS_CONFIG_RES 0x4000 /* 1=Local TX is Master, 0=Slave */
#define SR_1000T_MS_CONFIG_FAULT 0x8000 /* Master/Slave config fault */
#define SR_1000T_REMOTE_RX_STATUS_SHIFT 12
#define SR_1000T_LOCAL_RX_STATUS_SHIFT 13
/* Extended Status Register */
#define IEEE_ESR_1000T_HD_CAPS 0x1000 /* 1000T HD capable */
#define IEEE_ESR_1000T_FD_CAPS 0x2000 /* 1000T FD capable */
#define IEEE_ESR_1000X_HD_CAPS 0x4000 /* 1000X HD capable */
#define IEEE_ESR_1000X_FD_CAPS 0x8000 /* 1000X FD capable */
#define PHY_TX_POLARITY_MASK 0x0100 /* register 10h bit 8 (polarity bit) */
#define PHY_TX_NORMAL_POLARITY 0 /* register 10h bit 8 (normal polarity) */
#define AUTO_POLARITY_DISABLE 0x0010 /* register 11h bit 4 */
/* (0=enable, 1=disable) */
/* M88E1000 PHY Specific Control Register */
#define M88E1000_PSCR_JABBER_DISABLE 0x0001 /* 1=Jabber Function disabled */
#define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */
#define M88E1000_PSCR_SQE_TEST 0x0004 /* 1=SQE Test enabled */
#define M88E1000_PSCR_CLK125_DISABLE 0x0010 /* 1=CLK125 low,
* 0=CLK125 toggling
*/
#define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */
/* Manual MDI configuration */
#define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */
#define M88E1000_PSCR_AUTO_X_1000T 0x0040 /* 1000BASE-T: Auto crossover,
* 100BASE-TX/10BASE-T:
* MDI Mode
*/
#define M88E1000_PSCR_AUTO_X_MODE 0x0060 /* Auto crossover enabled
* all speeds.
*/
#define M88E1000_PSCR_10BT_EXT_DIST_ENABLE 0x0080
/* 1=Enable Extended 10BASE-T distance
* (Lower 10BASE-T RX Threshold)
* 0=Normal 10BASE-T RX Threshold */
#define M88E1000_PSCR_MII_5BIT_ENABLE 0x0100
/* 1=5-Bit interface in 100BASE-TX
* 0=MII interface in 100BASE-TX */
#define M88E1000_PSCR_SCRAMBLER_DISABLE 0x0200 /* 1=Scrambler disable */
#define M88E1000_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force link good */
#define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
#define M88E1000_PSCR_POLARITY_REVERSAL_SHIFT 1
#define M88E1000_PSCR_AUTO_X_MODE_SHIFT 5
#define M88E1000_PSCR_10BT_EXT_DIST_ENABLE_SHIFT 7
/* M88E1000 PHY Specific Status Register */
#define M88E1000_PSSR_JABBER 0x0001 /* 1=Jabber */
#define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */
#define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */
#define M88E1000_PSSR_CABLE_LENGTH 0x0380 /* 0=<50M;1=50-80M;2=80-110M;
* 3=110-140M;4=>140M */
#define M88E1000_PSSR_LINK 0x0400 /* 1=Link up, 0=Link down */
#define M88E1000_PSSR_SPD_DPLX_RESOLVED 0x0800 /* 1=Speed & Duplex resolved */
#define M88E1000_PSSR_PAGE_RCVD 0x1000 /* 1=Page received */
#define M88E1000_PSSR_DPLX 0x2000 /* 1=Duplex 0=Half Duplex */
#define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */
#define M88E1000_PSSR_10MBS 0x0000 /* 00=10Mbs */
#define M88E1000_PSSR_100MBS 0x4000 /* 01=100Mbs */
#define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */
#define M88E1000_PSSR_REV_POLARITY_SHIFT 1
#define M88E1000_PSSR_MDIX_SHIFT 6
#define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7
/* M88E1000 Extended PHY Specific Control Register */
#define M88E1000_EPSCR_FIBER_LOOPBACK 0x4000 /* 1=Fiber loopback */
#define M88E1000_EPSCR_DOWN_NO_IDLE 0x8000 /* 1=Lost lock detect enabled.
* Will assert lost lock and bring
* link down if idle not seen
* within 1ms in 1000BASE-T
*/
/* Number of times we will attempt to autonegotiate before downshifting if we
* are the master */
#define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00
#define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 0x0000
#define M88E1000_EPSCR_MASTER_DOWNSHIFT_2X 0x0400
#define M88E1000_EPSCR_MASTER_DOWNSHIFT_3X 0x0800
#define M88E1000_EPSCR_MASTER_DOWNSHIFT_4X 0x0C00
/* Number of times we will attempt to autonegotiate before downshifting if we
* are the slave */
#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK 0x0300
#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_DIS 0x0000
#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100
#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_2X 0x0200
#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_3X 0x0300
#define M88E1000_EPSCR_TX_CLK_2_5 0x0060 /* 2.5 MHz TX_CLK */
#define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */
#define M88E1000_EPSCR_TX_CLK_0 0x0000 /* NO TX_CLK */
/* Bit definitions for valid PHY IDs. */
#define M88E1000_E_PHY_ID 0x01410C50
#define M88E1000_I_PHY_ID 0x01410C30
#define M88E1011_I_PHY_ID 0x01410C20
#define M88E1000_12_PHY_ID M88E1000_E_PHY_ID
#define M88E1000_14_PHY_ID M88E1000_E_PHY_ID
#define IGP01E1000_I_PHY_ID 0x02A80380
#define M88E1011_I_REV_4 0x04
#define M88E1111_I_PHY_ID 0x01410CC0
#define L1LXT971A_PHY_ID 0x001378E0
#define GG82563_E_PHY_ID 0x01410CA0
#define I350_I_PHY_ID 0x015403B0
#define BME1000_E_PHY_ID 0x01410CB0
#define I210_I_PHY_ID 0x01410C00
/* Miscellaneous PHY bit definitions. */
#define PHY_PREAMBLE 0xFFFFFFFF
#define PHY_SOF 0x01
#define PHY_OP_READ 0x02
#define PHY_OP_WRITE 0x01
#define PHY_TURNAROUND 0x02
#define PHY_PREAMBLE_SIZE 32
#define MII_CR_SPEED_1000 0x0040
#define MII_CR_SPEED_100 0x2000
#define MII_CR_SPEED_10 0x0000
#define E1000_PHY_ADDRESS 0x01
#define PHY_AUTO_NEG_TIME 45 /* 4.5 Seconds */
#define PHY_FORCE_TIME 20 /* 2.0 Seconds */
#define PHY_REVISION_MASK 0xFFFFFFF0
#define DEVICE_SPEED_MASK 0x00000300 /* Device Ctrl Reg Speed Mask */
#define REG4_SPEED_MASK 0x01E0
#define REG9_SPEED_MASK 0x0300
#define ADVERTISE_10_HALF 0x0001
#define ADVERTISE_10_FULL 0x0002
#define ADVERTISE_100_HALF 0x0004
#define ADVERTISE_100_FULL 0x0008
#define ADVERTISE_1000_HALF 0x0010
#define ADVERTISE_1000_FULL 0x0020
#define ICH_FLASH_GFPREG 0x0000
#define ICH_FLASH_HSFSTS 0x0004
#define ICH_FLASH_HSFCTL 0x0006
#define ICH_FLASH_FADDR 0x0008
#define ICH_FLASH_FDATA0 0x0010
#define ICH_FLASH_FRACC 0x0050
#define ICH_FLASH_FREG0 0x0054
#define ICH_FLASH_FREG1 0x0058
#define ICH_FLASH_FREG2 0x005C
#define ICH_FLASH_FREG3 0x0060
#define ICH_FLASH_FPR0 0x0074
#define ICH_FLASH_FPR1 0x0078
#define ICH_FLASH_SSFSTS 0x0090
#define ICH_FLASH_SSFCTL 0x0092
#define ICH_FLASH_PREOP 0x0094
#define ICH_FLASH_OPTYPE 0x0096
#define ICH_FLASH_OPMENU 0x0098
#define ICH_FLASH_REG_MAPSIZE 0x00A0
#define ICH_FLASH_SECTOR_SIZE 4096
#define ICH_GFPREG_BASE_MASK 0x1FFF
#define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF
#define E1000_SW_FW_SYNC 0x05B5C /* Software-Firmware Synchronization - RW */
/* SPI EEPROM Status Register */
#define EEPROM_STATUS_RDY_SPI 0x01
#define EEPROM_STATUS_WEN_SPI 0x02
#define EEPROM_STATUS_BP0_SPI 0x04
#define EEPROM_STATUS_BP1_SPI 0x08
#define EEPROM_STATUS_WPEN_SPI 0x80
/* SW Semaphore Register */
#define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */
#define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */
#define E1000_SWSM_WMNG 0x00000004 /* Wake MNG Clock */
#define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */
/* FW Semaphore Register */
#define E1000_FWSM_MODE_MASK 0x0000000E /* FW mode */
#define E1000_FWSM_MODE_SHIFT 1
#define E1000_FWSM_FW_VALID 0x00008000 /* FW established a valid mode */
#define E1000_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI reset */
#define E1000_FWSM_DISSW 0x10000000 /* FW disable SW Write Access */
#define E1000_FWSM_SKUSEL_MASK 0x60000000 /* LAN SKU select */
#define E1000_FWSM_SKUEL_SHIFT 29
#define E1000_FWSM_SKUSEL_EMB 0x0 /* Embedded SKU */
#define E1000_FWSM_SKUSEL_CONS 0x1 /* Consumer SKU */
#define E1000_FWSM_SKUSEL_PERF_100 0x2 /* Perf & Corp 10/100 SKU */
#define E1000_FWSM_SKUSEL_PERF_GBE 0x3 /* Perf & Copr GbE SKU */
#define E1000_GCR 0x05B00 /* PCI-Ex Control */
#define E1000_GSCL_1 0x05B10 /* PCI-Ex Statistic Control #1 */
#define E1000_GSCL_2 0x05B14 /* PCI-Ex Statistic Control #2 */
#define E1000_GSCL_3 0x05B18 /* PCI-Ex Statistic Control #3 */
#define E1000_GSCL_4 0x05B1C /* PCI-Ex Statistic Control #4 */
#define E1000_FACTPS 0x05B30 /* Function Active and Power State to MNG */
#define E1000_SWSM 0x05B50 /* SW Semaphore */
#define E1000_FWSM 0x05B54 /* FW Semaphore */
#define E1000_FFLT_DBG 0x05F04 /* Debug Register */
#define E1000_HICR 0x08F00 /* Host Inteface Control */
#define IGP_ACTIVITY_LED_MASK 0xFFFFF0FF
#define IGP_ACTIVITY_LED_ENABLE 0x0300
#define IGP_LED3_MODE 0x07000000
/* Mask bit for PHY class in Word 7 of the EEPROM */
#define EEPROM_PHY_CLASS_A 0x8000
#define AUTONEG_ADVERTISE_SPEED_DEFAULT 0x002F /* Everything but 1000-Half */
#define AUTONEG_ADVERTISE_10_100_ALL 0x000F /* All 10/100 speeds*/
#define AUTONEG_ADVERTISE_10_ALL 0x0003 /* 10Mbps Full & Half speeds*/
#define E1000_KUMCTRLSTA_MASK 0x0000FFFF
#define E1000_KUMCTRLSTA_OFFSET 0x001F0000
#define E1000_KUMCTRLSTA_OFFSET_SHIFT 16
#define E1000_KUMCTRLSTA_REN 0x00200000
#define E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL 0x00000000
#define E1000_KUMCTRLSTA_OFFSET_CTRL 0x00000001
#define E1000_KUMCTRLSTA_OFFSET_INB_CTRL 0x00000002
#define E1000_KUMCTRLSTA_OFFSET_DIAG 0x00000003
#define E1000_KUMCTRLSTA_OFFSET_TIMEOUTS 0x00000004
#define E1000_KUMCTRLSTA_OFFSET_INB_PARAM 0x00000009
#define E1000_KUMCTRLSTA_OFFSET_HD_CTRL 0x00000010
#define E1000_KUMCTRLSTA_OFFSET_M2P_SERDES 0x0000001E
#define E1000_KUMCTRLSTA_OFFSET_M2P_MODES 0x0000001F
/* FIFO Control */
#define E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS 0x00000008
#define E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS 0x00000800
/* In-Band Control */
#define E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT 0x00000500
#define E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING 0x00000010
/* Half-Duplex Control */
#define E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT 0x00000004
#define E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT 0x00000000
#define E1000_KUMCTRLSTA_OFFSET_K0S_CTRL 0x0000001E
#define E1000_KUMCTRLSTA_DIAG_FELPBK 0x2000
#define E1000_KUMCTRLSTA_DIAG_NELPBK 0x1000
#define E1000_KUMCTRLSTA_K0S_100_EN 0x2000
#define E1000_KUMCTRLSTA_K0S_GBE_EN 0x1000
#define E1000_KUMCTRLSTA_K0S_ENTRY_LATENCY_MASK 0x0003
#define E1000_MNG_ICH_IAMT_MODE 0x2
#define E1000_MNG_IAMT_MODE 0x3
#define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */
#define E1000_KUMCTRLSTA 0x00034 /* MAC-PHY interface - RW */
/* Number of milliseconds we wait for PHY configuration done after MAC reset */
#define PHY_CFG_TIMEOUT 100
#define DEFAULT_80003ES2LAN_TIPG_IPGT_10_100 0x00000009
#define DEFAULT_80003ES2LAN_TIPG_IPGT_1000 0x00000008
#define AUTO_ALL_MODES 0
#ifndef E1000_MASTER_SLAVE
/* Switch to override PHY master/slave setting */
#define E1000_MASTER_SLAVE e1000_ms_hw_default
#endif
/* Extended Transmit Control */
#define E1000_TCTL_EXT_BST_MASK 0x000003FF /* Backoff Slot Time */
#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */
#define DEFAULT_80003ES2LAN_TCTL_EXT_GCEX 0x00010000
#define PCI_EX_82566_SNOOP_ALL PCI_EX_NO_SNOOP_ALL
#define E1000_GCR_L1_ACT_WITHOUT_L0S_RX 0x08000000
#define E1000_MC_TBL_SIZE_ICH8LAN 32
#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers
after IMS clear */
#endif /* _E1000_HW_H_ */
