/*
* Copyright 2004 Freescale Semiconductor.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* mpc8555cds board configuration file
*
* Please refer to doc/README.mpc85xxcds for more info.
*
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* High Level Configuration Options */
#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41 */
#define CONFIG_CPM2 1 /* has CPM2 */
#define CONFIG_MPC8555 1 /* MPC8555 specific */
#define CONFIG_MPC8555CDS 1 /* MPC8555CDS board specific */
#define CONFIG_PCI
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_DLL /* possible DLL fix needed */
#undef CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
/*
* When initializing flash, if we cannot find the manufacturer ID,
* assume this is the AMD flash associated with the CDS board.
* This allows booting from a promjet.
*/
#define CONFIG_ASSUME_AMD_FLASH
#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */
#ifndef __ASSEMBLY__
extern unsigned long get_clock_freq(void);
#endif
#define CONFIG_SYS_CLK_FREQ get_clock_freq() /* sysclk for MPC85xx */
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#undef CFG_DRAM_TEST /* memory test, takes time */
#define CFG_MEMTEST_START 0x00200000 /* memtest works on */
#define CFG_MEMTEST_END 0x00400000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
/*
* DDR Setup
*/
#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
/*
* Make sure required options are set
*/
#ifndef CONFIG_SPD_EEPROM
#error ("CONFIG_SPD_EEPROM is required by MPC85555CDS")
#endif
#undef CONFIG_CLOCKS_IN_MHZ
/*
* Local Bus Definitions
*/
/*
* FLASH on the Local Bus
* Two banks, 8M each, using the CFI driver.
* Boot from BR0/OR0 bank at 0xff00_0000
* Alternate BR1/OR1 bank at 0xff80_0000
*
* BR0, BR1:
* Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
* Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
* Port Size = 16 bits = BRx[19:20] = 10
* Use GPCM = BRx[24:26] = 000
* Valid = BRx[31] = 1
*
* 0 4 8 12 16 20 24 28
* 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0
* 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1
*
* OR0, OR1:
* Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
* Reserved ORx[17:18] = 11, confusion here?
* CSNT = ORx[20] = 1
* ACS = half cycle delay = ORx[21:22] = 11
* SCY = 6 = ORx[24:27] = 0110
* TRLX = use relaxed timing = ORx[29] = 1
* EAD = use external address latch delay = OR[31] = 1
*
* 0 4 8 12 16 20 24 28
* 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx
*/
#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 8M */
#define CFG_BR0_PRELIM 0xff801001
#define CFG_BR1_PRELIM 0xff001001
#define CFG_OR0_PRELIM 0xff806e65
#define CFG_OR1_PRELIM 0xff806e65
#define CFG_FLASH_BANKS_LIST {0xff800000, CFG_FLASH_BASE}
#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
#define CFG_FLASH_CFI_DRIVER
#define CFG_FLASH_CFI
#define CFG_FLASH_EMPTY_INFO
/*
* SDRAM on the Local Bus
*/
#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
/*
* Base Register 2 and Option Register 2 configure SDRAM.
* The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
*
* For BR2, need:
* Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
* port-size = 32-bits = BR2[19:20] = 11
* no parity checking = BR2[21:22] = 00
* SDRAM for MSEL = BR2[24:26] = 011
* Valid = BR[31] = 1
*
* 0 4 8 12 16 20 24 28
* 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
*
* FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into
* FIXME: the top 17 bits of BR2.
*/
#define CFG_BR2_PRELIM 0xf0001861
/*
* The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
*
* For OR2, need:
* 64MB mask for AM, OR2[0:7] = 1111 1100
* XAM, OR2[17:18] = 11
* 9 columns OR2[19-21] = 010
* 13 rows OR2[23-25] = 100
* EAD set for extra time OR[31] = 1
*
* 0 4 8 12 16 20 24 28
* 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
*/
#define CFG_OR2_PRELIM 0xfc006901
#define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */
#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
#define CFG_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/
/*
* LSDMR masks
*/
#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1))
#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16))
#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23))
#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27))
#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31))
#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
/*
* Common settings for all Local Bus SDRAM commands.
* At run time, either BSMA1516 (for CPU 1.1)
* or BSMA1617 (for CPU 1.0) (old)
* is OR'ed in too.
*/
#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_RFCR16 \
| CFG_LBC_LSDMR_PRETOACT7 \
| CFG_LBC_LSDMR_ACTTORW7 \
| CFG_LBC_LSDMR_BL8 \
| CFG_LBC_LSDMR_WRC4 \
| CFG_LBC_LSDMR_CL3 \
| CFG_LBC_LSDMR_RFEN \
)
/*
* The CADMUS registers are connected to CS3 on CDS.
* The new memory map places CADMUS at 0xf8000000.
*
* For BR3, need:
* Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
* port-size = 8-bits = BR[19:20] = 01
* no parity checking = BR[21:22] = 00
* GPMC for MSEL = BR[24:26] = 000
* Valid = BR[31] = 1
*
* 0 4 8 12 16 20 24 28
* 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
*
* For OR3, need:
* 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0
* disable buffer ctrl OR[19] = 0
* CSNT OR[20] = 1
* ACS OR[21:22] = 11
* XACS OR[23] = 1
* SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe
* SETA OR[28] = 0
* TRLX OR[29] = 1
* EHTR OR[30] = 1
* EAD extra time OR[31] = 1
*
* 0 4 8 12 16 20 24 28
* 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
*/
#define CADMUS_BASE_ADDR 0xf8000000
#define CFG_BR3_PRELIM 0xf8000801
#define CFG_OR3_PRELIM 0xfff00ff7
#define CONFIG_L1_INIT_RAM
#define CFG_INIT_RAM_LOCK 1
#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 2
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_NS16550
#define CFG_NS16550_SERIAL
#define CFG_NS16550_REG_SIZE 1
#define CFG_NS16550_CLK get_bus_freq(0)
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
/* pass open firmware flat tree */
#define CONFIG_OF_FLAT_TREE 1
#define CONFIG_OF_BOARD_SETUP 1
/* maximum size of the flat tree (8K) */
#define OF_FLAT_TREE_MAX_SIZE 8192
#define OF_CPU "PowerPC,8555@0"
#define OF_SOC "soc8555@e0000000"
#define OF_TBCLK (bd->bi_busfreq / 8)
#define OF_STDOUT_PATH "/soc8555@e0000000/serial@4600"
/*
* I2C
*/
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_EEPROM_ADDR 0x57
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
#define CFG_I2C_OFFSET 0x3000
/*
* General PCI
* Addresses are mapped 1-1.
*/
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
#define CFG_PCI1_IO_BASE 0x00000000
#define CFG_PCI1_IO_PHYS 0xe2000000
#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
#define CFG_PCI2_MEM_BASE 0xa0000000
#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
#define CFG_PCI2_IO_BASE 0x00000000
#define CFG_PCI2_IO_PHYS 0xe2100000
#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
#if defined(CONFIG_PCI)
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_MPC85XX_PCI2
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
#endif /* CONFIG_PCI */
#if defined(CONFIG_TSEC_ENET)
#ifndef CONFIG_NET_MULTI
#define CONFIG_NET_MULTI 1
#endif
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MPC85XX_TSEC1 1
#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0"
#define CONFIG_MPC85XX_TSEC2 1
#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
#undef CONFIG_MPC85XX_FEC
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define FEC_PHY_ADDR 3
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define FEC_PHYIDX 0
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#endif /* CONFIG_TSEC_ENET */
/*
* Environment
*/
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
#define CFG_ENV_SIZE 0x2000
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#if defined(CONFIG_PCI)
#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
| CFG_CMD_PCI \
| CFG_CMD_PING \
| CFG_CMD_I2C \
| CFG_CMD_MII)
#else
#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
| CFG_CMD_PING \
| CFG_CMD_I2C \
| CFG_CMD_MII)
#endif
#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
/* Cache Configuration */
#define CFG_DCACHE_SIZE 32768
#define CFG_CACHELINE_SIZE 32
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
#endif
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Environment Configuration
*/
/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
#define CONFIG_HAS_ETH1
#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
#define CONFIG_HAS_ETH2
#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
#endif
#define CONFIG_IPADDR 192.168.1.253
#define CONFIG_HOSTNAME unknown
#define CONFIG_ROOTPATH /nfsroot
#define CONFIG_BOOTFILE your.uImage
#define CONFIG_SERVERIP 192.168.1.1
#define CONFIG_GATEWAYIP 192.168.1.1
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/
#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
#define CONFIG_BAUDRATE 115200
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS1\0" \
"ramdiskaddr=600000\0" \
"ramdiskfile=your.ramdisk.u-boot\0" \
"fdtaddr=400000\0" \
"fdtfile=your.fdt.dtb\0"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
"bootm $loadaddr $ramdiskaddr"
#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
#endif /* __CONFIG_H */
