/*
* Copyright 2006 Freescale Semiconductor.
*
* Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* MPC8641HPCN board configuration file
*
* Make sure you change the MAC address and other network params first,
* search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* High Level Configuration Options */
#define CONFIG_MPC86xx 1 /* MPC86xx */
#define CONFIG_MPC8641 1 /* MPC8641 specific */
#define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */
#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */
#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
#undef DEBUG
#ifdef RUN_DIAG
#define CFG_DIAG_ADDR 0xff800000
#endif
#define CFG_RESET_ADDRESS 0xfff00100
/*#undef CONFIG_PCI*/
#define CONFIG_PCI
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#undef CONFIG_DDR_DLL /* possible DLL fix needed */
#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
#define CONFIG_NUM_DDR_CONTROLLERS 2
/* #define CONFIG_DDR_INTERLEAVE 1 */
#define CACHE_LINE_INTERLEAVING 0x20000000
#define PAGE_INTERLEAVING 0x21000000
#define BANK_INTERLEAVING 0x22000000
#define SUPER_BANK_INTERLEAVING 0x23000000
#define CONFIG_ALTIVEC 1
/*
* L2CR setup -- make sure this is right for your board!
*/
#define CFG_L2
#define L2_INIT 0
#define L2_ENABLE (L2CR_L2E)
#ifndef CONFIG_SYS_CLK_FREQ
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
#endif
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#undef CFG_DRAM_TEST /* memory test, takes time */
#define CFG_MEMTEST_START 0x00200000 /* memtest region */
#define CFG_MEMTEST_END 0x00400000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CFG_CCSRBAR 0xf8000000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
/*
* DDR Setup
*/
#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
#define CONFIG_VERY_BIG_RAM
#define MPC86xx_DDR_SDRAM_CLK_CNTL
#if defined(CONFIG_SPD_EEPROM)
/*
* Determine DDR configuration from I2C interface.
*/
#define SPD_EEPROM_ADDRESS1 0x51 /* DDR DIMM */
#define SPD_EEPROM_ADDRESS2 0x52 /* DDR DIMM */
#define SPD_EEPROM_ADDRESS3 0x53 /* DDR DIMM */
#define SPD_EEPROM_ADDRESS4 0x54 /* DDR DIMM */
#else
/*
* Manually set up DDR1 parameters
*/
#define CFG_SDRAM_SIZE 256 /* DDR is 256MB */
#define CFG_DDR_CS0_BNDS 0x0000000F
#define CFG_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */
#define CFG_DDR_EXT_REFRESH 0x00000000
#define CFG_DDR_TIMING_0 0x00260802
#define CFG_DDR_TIMING_1 0x39357322
#define CFG_DDR_TIMING_2 0x14904cc8
#define CFG_DDR_MODE_1 0x00480432
#define CFG_DDR_MODE_2 0x00000000
#define CFG_DDR_INTERVAL 0x06090100
#define CFG_DDR_DATA_INIT 0xdeadbeef
#define CFG_DDR_CLK_CTRL 0x03800000
#define CFG_DDR_OCD_CTRL 0x00000000
#define CFG_DDR_OCD_STATUS 0x00000000
#define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */
#define CFG_DDR_CONTROL2 0x04400000
/* Not used in fixed_sdram function */
#define CFG_DDR_MODE 0x00000022
#define CFG_DDR_CS1_BNDS 0x00000000
#define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */
#define CFG_DDR_CS3_BNDS 0x00000FFF /* Not done */
#define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */
#define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */
#endif
#define CFG_ID_EEPROM 1
#define ID_EEPROM_ADDR 0x57
/*
* In MPC8641HPCN, allocate 16MB flash spaces at fe000000 and ff000000.
* There is an 8MB flash. In effect, the addresses from fe000000 to fe7fffff
* map to fe800000 to ffffffff, and ff000000 to ff7fffff map to ffffffff.
* However, when u-boot comes up, the flash_init needs hard start addresses
* to build its info table. For user convenience, the flash addresses is
* fe800000 and ff800000. That way, u-boot knows where the flash is
* and the user can download u-boot code from promjet to fef00000, a
* more intuitive location than fe700000.
*
* Note that, on switching the boot location, fef00000 becomes fff00000.
*/
#define CFG_FLASH_BASE 0xfe800000 /* start of FLASH 32M */
#define CFG_FLASH_BASE2 0xff800000
#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}
#define CFG_BR0_PRELIM 0xff001001 /* port size 16bit */
#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Boot Flash area*/
#define CFG_BR1_PRELIM 0xfe001001 /* port size 16bit */
#define CFG_OR1_PRELIM 0xff006ff7 /* 16MB Alternate Boot Flash area*/
#define CFG_BR2_PRELIM 0xf8201001 /* port size 16bit */
#define CFG_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/
#define CFG_BR3_PRELIM 0xf8100801 /* port size 8bit */
#define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/
#define PIXIS_BASE 0xf8100000 /* PIXIS registers */
#define PIXIS_ID 0x0 /* Board ID at offset 0 */
#define PIXIS_VER 0x1 /* Board version at offset 1 */
#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
#define PIXIS_RST 0x4 /* PIXIS Reset Control register */
#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch register */
#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */
#define PIXIS_VCTL 0x10 /* VELA Control Register */
#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
#define CFG_FLASH_CFI_DRIVER
#define CFG_FLASH_CFI
#define CFG_FLASH_EMPTY_INFO
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#else
#undef CFG_RAMBOOT
#endif
#if defined(CFG_RAMBOOT)
#undef CFG_FLASH_CFI_DRIVER
#undef CONFIG_SPD_EEPROM
#define CFG_SDRAM_SIZE 256
#endif
#undef CONFIG_CLOCKS_IN_MHZ
#define CONFIG_L1_INIT_RAM
#define CFG_INIT_RAM_LOCK 1
#ifndef CFG_INIT_RAM_LOCK
#define CFG_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */
#else
#define CFG_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */
#endif
#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_NS16550
#define CFG_NS16550_SERIAL
#define CFG_NS16550_REG_SIZE 1
#define CFG_NS16550_CLK get_bus_freq(0)
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
/*
* Pass open firmware flat tree to kernel
*/
#define CONFIG_OF_FLAT_TREE 1
#define CONFIG_OF_BOARD_SETUP 1
/* maximum size of the flat tree (8K) */
#define OF_FLAT_TREE_MAX_SIZE 8192
#define OF_CPU "PowerPC,8641@0"
#define OF_SOC "soc8641@f8000000"
#define OF_TBCLK (bd->bi_busfreq / 4)
#define OF_STDOUT_PATH "/soc8641@f8000000/serial@4500"
#define CFG_64BIT_VSPRINTF 1
#define CFG_64BIT_STRTOUL 1
/*
* I2C
*/
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
#define CFG_I2C_OFFSET 0x3100
/*
* RapidIO MMU
*/
#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
/*
* General PCI
* Addresses are mapped 1-1.
*/
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
#define CFG_PCI1_IO_BASE 0xe2000000
#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
/* PCI view of System Memory */
#define CFG_PCI_MEMORY_BUS 0x00000000
#define CFG_PCI_MEMORY_PHYS 0x00000000
#define CFG_PCI_MEMORY_SIZE 0x80000000
/* For RTL8139 */
#define KSEG1ADDR(x) ({u32 _x=le32_to_cpu(*(u32 *)(x)); (&_x);})
#define _IO_BASE 0x00000000
#define CFG_PCI2_MEM_BASE 0xa0000000
#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */
#define CFG_PCI2_IO_BASE 0xe3000000
#define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE
#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */
#if defined(CONFIG_PCI)
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#undef CFG_SCSI_SCAN_BUS_REVERSE
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_RTL8139
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
#if !defined(CONFIG_PCI_PNP)
#define PCI_ENET0_IOADDR 0xe0000000
#define PCI_ENET0_MEMADDR 0xe0000000
#define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
#endif
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_DOS_PARTITION
#define CONFIG_SCSI_AHCI
#ifdef CONFIG_SCSI_AHCI
#define CONFIG_SATA_ULI5288
#define CFG_SCSI_MAX_SCSI_ID 4
#define CFG_SCSI_MAX_LUN 1
#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
#endif
#endif /* CONFIG_PCI */
#if defined(CONFIG_TSEC_ENET)
#ifndef CONFIG_NET_MULTI
#define CONFIG_NET_MULTI 1
#endif
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MPC86XX_TSEC1 1
#define CONFIG_MPC86XX_TSEC1_NAME "eTSEC1"
#define CONFIG_MPC86XX_TSEC2 1
#define CONFIG_MPC86XX_TSEC2_NAME "eTSEC2"
#define CONFIG_MPC86XX_TSEC3 1
#define CONFIG_MPC86XX_TSEC3_NAME "eTSEC3"
#define CONFIG_MPC86XX_TSEC4 1
#define CONFIG_MPC86XX_TSEC4_NAME "eTSEC4"
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC3_PHY_ADDR 2
#define TSEC4_PHY_ADDR 3
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
#define TSEC4_PHYIDX 0
#define CONFIG_ETHPRIME "eTSEC1"
#endif /* CONFIG_TSEC_ENET */
/*
* BAT0 2G Cacheable, non-guarded
* 0x0000_0000 2G DDR
*/
#define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
#define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
#define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE )
#define CFG_IBAT0U CFG_DBAT0U
/*
* BAT1 1G Cache-inhibited, guarded
* 0x8000_0000 512M PCI-Express 1 Memory
* 0xa000_0000 512M PCI-Express 2 Memory
* Changed it for operating from 0xd0000000
*/
#define CFG_DBAT1L ( CFG_PCI1_MEM_BASE | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_DBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT1U CFG_DBAT1U
/*
* BAT2 512M Cache-inhibited, guarded
* 0xc000_0000 512M RapidIO Memory
*/
#define CFG_DBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_DBAT2U (CFG_RIO_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP)
#define CFG_IBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT2U CFG_DBAT2U
/*
* BAT3 4M Cache-inhibited, guarded
* 0xf800_0000 4M CCSR
*/
#define CFG_DBAT3L ( CFG_CCSRBAR | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_DBAT3U (CFG_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP)
#define CFG_IBAT3L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT3U CFG_DBAT3U
/*
* BAT4 32M Cache-inhibited, guarded
* 0xe200_0000 16M PCI-Express 1 I/O
* 0xe300_0000 16M PCI-Express 2 I/0
* Note that this is at 0xe0000000
*/
#define CFG_DBAT4L ( CFG_PCI1_IO_BASE | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_DBAT4U (CFG_PCI1_IO_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
#define CFG_IBAT4L (CFG_PCI1_IO_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT4U CFG_DBAT4U
/*
* BAT5 128K Cacheable, non-guarded
* 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
*/
#define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
#define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
#define CFG_IBAT5L CFG_DBAT5L
#define CFG_IBAT5U CFG_DBAT5U
/*
* BAT6 32M Cache-inhibited, guarded
* 0xfe00_0000 32M FLASH
*/
#define CFG_DBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_DBAT6U ((CFG_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP)
#define CFG_IBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE)
#define CFG_IBAT6U CFG_DBAT6U
#define CFG_DBAT7L 0x00000000
#define CFG_DBAT7U 0x00000000
#define CFG_IBAT7L 0x00000000
#define CFG_IBAT7U 0x00000000
/*
* Environment
*/
#ifndef CFG_RAMBOOT
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
#define CFG_ENV_SIZE 0x2000
#else
#define CFG_NO_FLASH 1 /* Flash is not usable now */
#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
#define CFG_ENV_SIZE 0x2000
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#if defined(CFG_RAMBOOT)
#if defined(CONFIG_PCI)
#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
| CFG_CMD_PING \
| CFG_CMD_PCI \
| CFG_CMD_I2C \
| CFG_CMD_SCSI \
| CFG_CMD_EXT2) \
& \
~(CFG_CMD_ENV \
| CFG_CMD_IMLS \
| CFG_CMD_FLASH \
| CFG_CMD_LOADS))
#else
#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
| CFG_CMD_PING \
| CFG_CMD_I2C \
| CFG_CMD_SCSI \
| CGF_CMD_EXT2) \
& \
~(CFG_CMD_ENV \
| CFG_CMD_IMLS \
| CFG_CMD_FLASH \
| CFG_CMD_LOADS))
#endif
#else
#if defined(CONFIG_PCI)
#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
| CFG_CMD_PCI \
| CFG_CMD_PING \
| CFG_CMD_I2C \
| CFG_CMD_SCSI \
| CFG_CMD_EXT2)
#else
#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
| CFG_CMD_PING \
| CFG_CMD_I2C)
#endif
#endif
#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
/* Cache Configuration */
#define CFG_DCACHE_SIZE 32768
#define CFG_CACHELINE_SIZE 32
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
#endif
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Environment Configuration
*/
/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_ETHADDR 00:E0:0C:00:00:01
#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD
#endif
#define CONFIG_HAS_ETH1 1
#define CONFIG_HAS_ETH2 1
#define CONFIG_HAS_ETH3 1
#define CONFIG_IPADDR 192.168.1.100
#define CONFIG_HOSTNAME unknown
#define CONFIG_ROOTPATH /opt/nfsroot
#define CONFIG_BOOTFILE uImage
#define CONFIG_SERVERIP 192.168.1.1
#define CONFIG_GATEWAYIP 192.168.1.1
#define CONFIG_NETMASK 255.255.255.0
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 1000000
#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_BAUDRATE 115200
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=your.ramdisk.u-boot\0" \
"dtbaddr=400000\0" \
"dtbfile=mpc8641_hpcn.dtb\0" \
"en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
"dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
"maxcpus=2"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $dtbaddr $dtbfile;" \
"bootm $loadaddr - $dtbaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
"tftp $dtbaddr $dtbfile;" \
"bootm $loadaddr $ramdiskaddr $dtbaddr"
#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
#endif /* __CONFIG_H */
