/*
* On-Chip devices setup code for the AT91SAM9x5 family
*
* Copyright (C) 2010 Atmel Corporation.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
*/
#include <common.h>
#include <linux/sizes.h>
#include <gpio.h>
#include <asm/armlinux.h>
#include <mach/hardware.h>
#include <mach/board.h>
#include <mach/at91_pmc.h>
#include <mach/at91sam9x5_matrix.h>
#include <mach/at91sam9_ddrsdr.h>
#include <mach/io.h>
#include <mach/iomux.h>
#include <mach/cpu.h>
#include <i2c/i2c-gpio.h>
#include "generic.h"
void at91_add_device_sdram(u32 size)
{
if (!size)
size = at91sam9x5_get_ddram_size();
arm_add_mem_device("ram0", AT91_CHIPSELECT_1, size);
add_mem_device("sram0", AT91SAM9X5_SRAM_BASE,
AT91SAM9X5_SRAM_SIZE, IORESOURCE_MEM_WRITEABLE);
}
/* --------------------------------------------------------------------
* USB Host (OHCI)
* -------------------------------------------------------------------- */
#if defined(CONFIG_USB_OHCI)
void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data)
{
int i;
if (!data)
return;
/* Enable VBus control for UHP ports */
for (i = 0; i < data->ports; i++) {
if (gpio_is_valid(data->vbus_pin[i]))
at91_set_gpio_output(data->vbus_pin[i],
data->vbus_pin_active_low[i]);
}
add_generic_device("at91_ohci", DEVICE_ID_DYNAMIC, NULL, AT91SAM9X5_OHCI_BASE,
SZ_1M, IORESOURCE_MEM, data);
}
#else
void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data) {}
#endif
#if defined(CONFIG_USB_EHCI)
void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data)
{
int i;
if (!data)
return;
/* Enable VBus control for UHP ports */
for (i = 0; i < data->ports; i++) {
if (gpio_is_valid(data->vbus_pin[i]))
at91_set_gpio_output(data->vbus_pin[i],
data->vbus_pin_active_low[i]);
}
add_generic_device("atmel-ehci", DEVICE_ID_SINGLE, NULL, AT91SAM9X5_EHCI_BASE,
1024 * 1024, IORESOURCE_MEM, data);
}
#else
void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data) {}
#endif
#if defined(CONFIG_DRIVER_NET_MACB)
void at91_add_device_eth(int id, struct macb_platform_data *data)
{
resource_size_t start;
if (!data)
return;
if (cpu_is_at91sam9g15())
return;
if (id && !cpu_is_at91sam9x25())
return;
switch (id) {
case 0:
start = AT91SAM9X5_BASE_EMAC0;
/* Pins used for MII and RMII */
at91_set_A_periph(AT91_PIN_PB4, 0); /* ETXCK_EREFCK */
at91_set_A_periph(AT91_PIN_PB3, 0); /* ERXDV */
at91_set_A_periph(AT91_PIN_PB0, 0); /* ERX0 */
at91_set_A_periph(AT91_PIN_PB1, 0); /* ERX1 */
at91_set_A_periph(AT91_PIN_PB2, 0); /* ERXER */
at91_set_A_periph(AT91_PIN_PB7, 0); /* ETXEN */
at91_set_A_periph(AT91_PIN_PB9, 0); /* ETX0 */
at91_set_A_periph(AT91_PIN_PB10, 0); /* ETX1 */
at91_set_A_periph(AT91_PIN_PB5, 0); /* EMDIO */
at91_set_A_periph(AT91_PIN_PB6, 0); /* EMDC */
if (data->phy_interface != PHY_INTERFACE_MODE_RMII) {
at91_set_A_periph(AT91_PIN_PB16, 0); /* ECRS */
at91_set_A_periph(AT91_PIN_PB17, 0); /* ECOL */
at91_set_A_periph(AT91_PIN_PB13, 0); /* ERX2 */
at91_set_A_periph(AT91_PIN_PB14, 0); /* ERX3 */
at91_set_A_periph(AT91_PIN_PB15, 0); /* ERXCK */
at91_set_A_periph(AT91_PIN_PB11, 0); /* ETX2 */
at91_set_A_periph(AT91_PIN_PB12, 0); /* ETX3 */
at91_set_A_periph(AT91_PIN_PB8, 0); /* ETXER */
}
break;
case 1:
start = AT91SAM9X5_BASE_EMAC1;
if (data->phy_interface != PHY_INTERFACE_MODE_RMII)
pr_warn("AT91: Only RMII available on interface macb%d.\n", id);
/* Pins used for RMII */
at91_set_B_periph(AT91_PIN_PC29, 0); /* ETXCK_EREFCK */
at91_set_B_periph(AT91_PIN_PC28, 0); /* ECRSDV */
at91_set_B_periph(AT91_PIN_PC20, 0); /* ERX0 */
at91_set_B_periph(AT91_PIN_PC21, 0); /* ERX1 */
at91_set_B_periph(AT91_PIN_PC16, 0); /* ERXER */
at91_set_B_periph(AT91_PIN_PC27, 0); /* ETXEN */
at91_set_B_periph(AT91_PIN_PC18, 0); /* ETX0 */
at91_set_B_periph(AT91_PIN_PC19, 0); /* ETX1 */
at91_set_B_periph(AT91_PIN_PC31, 0); /* EMDIO */
at91_set_B_periph(AT91_PIN_PC30, 0); /* EMDC */
break;
default:
return;
}
add_generic_device("macb", id, NULL, start, SZ_16K,
IORESOURCE_MEM, data);
}
#else
void at91_add_device_eth(int id, struct macb_platform_data *data) {}
#endif
#if defined(CONFIG_MCI_ATMEL)
/* Consider only one slot : slot 0 */
void __init at91_add_device_mci(short mmc_id, struct atmel_mci_platform_data *data)
{
resource_size_t start = ~0;
if (!data)
return;
/* Must have at least one usable slot */
if (!data->bus_width)
return;
/* input/irq */
if (gpio_is_valid(data->detect_pin)) {
at91_set_gpio_input(data->detect_pin, 1);
at91_set_deglitch(data->detect_pin, 1);
}
if (gpio_is_valid(data->wp_pin))
at91_set_gpio_input(data->wp_pin, 1);
if (mmc_id == 0) { /* MCI0 */
start = AT91SAM9X5_BASE_MCI0;
/* CLK */
at91_set_A_periph(AT91_PIN_PA17, 0);
/* CMD */
at91_set_A_periph(AT91_PIN_PA16, 1);
/* DAT0, maybe DAT1..DAT3 */
at91_set_A_periph(AT91_PIN_PA15, 1);
if (data->bus_width == 4) {
at91_set_A_periph(AT91_PIN_PA18, 1);
at91_set_A_periph(AT91_PIN_PA19, 1);
at91_set_A_periph(AT91_PIN_PA20, 1);
}
} else { /* MCI1 */
start = AT91SAM9X5_BASE_MCI1;
/* CLK */
at91_set_B_periph(AT91_PIN_PA13, 0);
/* CMD */
at91_set_B_periph(AT91_PIN_PA12, 1);
/* DAT0, maybe DAT1..DAT3 */
at91_set_B_periph(AT91_PIN_PA11, 1);
if (data->bus_width == 4) {
at91_set_B_periph(AT91_PIN_PA2, 1);
at91_set_B_periph(AT91_PIN_PA3, 1);
at91_set_B_periph(AT91_PIN_PA4, 1);
}
}
add_generic_device("atmel_mci", mmc_id, NULL, start, SZ_16K,
IORESOURCE_MEM, data);
}
#else
void __init at91_add_device_mci(short mmc_id, struct atmel_mci_platform_data *data) {}
#endif
/* --------------------------------------------------------------------
* NAND / SmartMedia
* -------------------------------------------------------------------- */
#if defined(CONFIG_NAND_ATMEL)
static struct resource nand_resources[] = {
[0] = {
.start = AT91_CHIPSELECT_3,
.end = AT91_CHIPSELECT_3 + SZ_256M - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AT91_BASE_SYS + AT91_PMECC,
.end = AT91_BASE_SYS + AT91_PMECC + 0x600 - 1,
.flags = IORESOURCE_MEM,
},
[2] = {
.start = AT91_BASE_SYS + AT91_PMERRLOC,
.end = AT91_BASE_SYS + AT91_PMERRLOC + 0x200 - 1,
.flags = IORESOURCE_MEM,
},
[3] = {
.start = AT91SAM9X5_ROM_BASE,
.end = AT91SAM9X5_ROM_BASE + AT91SAM9X5_ROM_SIZE - 1,
.flags = IORESOURCE_MEM,
},
};
void __init at91_add_device_nand(struct atmel_nand_data *data)
{
unsigned long csa;
if (!data)
return;
csa = at91_sys_read(AT91_MATRIX_EBICSA);
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_NANDFLASH);
data->pmecc_lookup_table_offset = 0x8000;
/* enable pin */
if (gpio_is_valid(data->enable_pin))
at91_set_gpio_output(data->enable_pin, 1);
/* ready/busy pin */
if (gpio_is_valid(data->rdy_pin))
at91_set_gpio_input(data->rdy_pin, 1);
/* card detect pin */
if (gpio_is_valid(data->det_pin))
at91_set_gpio_input(data->det_pin, 1);
add_generic_device_res("atmel_nand", 0, nand_resources,
ARRAY_SIZE(nand_resources), data);
}
#else
void __init at91_add_device_nand(struct atmel_nand_data *data) {}
#endif
#if defined(CONFIG_I2C_GPIO)
static struct i2c_gpio_platform_data pdata_i2c0 = {
.sda_pin = AT91_PIN_PA30,
.sda_is_open_drain = 1,
.scl_pin = AT91_PIN_PA31,
.scl_is_open_drain = 1,
.udelay = 5, /* ~100 kHz */
};
static struct i2c_gpio_platform_data pdata_i2c1 = {
.sda_pin = AT91_PIN_PC0,
.sda_is_open_drain = 1,
.scl_pin = AT91_PIN_PC1,
.scl_is_open_drain = 1,
.udelay = 5, /* ~100 kHz */
};
static struct i2c_gpio_platform_data pdata_i2c2 = {
.sda_pin = AT91_PIN_PB4,
.sda_is_open_drain = 1,
.scl_pin = AT91_PIN_PB5,
.scl_is_open_drain = 1,
.udelay = 5, /* ~100 kHz */
};
void at91_add_device_i2c(short i2c_id, struct i2c_board_info *devices, int nr_devices)
{
struct i2c_gpio_platform_data *pdata;
i2c_register_board_info(i2c_id, devices, nr_devices);
switch (i2c_id) {
case 0:
pdata = &pdata_i2c0;
break;
case 1:
pdata = &pdata_i2c1;
break;
case 2:
pdata = &pdata_i2c2;
break;
default:
return;
}
at91_set_GPIO_periph(pdata->sda_pin, 1); /* TWD (SDA) */
at91_set_multi_drive(pdata->sda_pin, 1);
at91_set_GPIO_periph(pdata->scl_pin, 1); /* TWCK (SCL) */
at91_set_multi_drive(pdata->scl_pin, 1);
add_generic_device_res("i2c-gpio", i2c_id, NULL, 0, pdata);
}
#else
void at91_add_device_i2c(short i2c_id, struct i2c_board_info *devices, int nr_devices) {}
#endif
/* --------------------------------------------------------------------
* SPI
* -------------------------------------------------------------------- */
#if defined(CONFIG_DRIVER_SPI_ATMEL)
static unsigned spi0_standard_cs[4] = { AT91_PIN_PA14, AT91_PIN_PA7, AT91_PIN_PA1, AT91_PIN_PB3 };
static unsigned spi1_standard_cs[4] = { AT91_PIN_PA8, AT91_PIN_PA0, AT91_PIN_PA31, AT91_PIN_PA30 };
static struct at91_spi_platform_data spi_pdata[] = {
[0] = {
.chipselect = spi0_standard_cs,
.num_chipselect = ARRAY_SIZE(spi0_standard_cs),
},
[1] = {
.chipselect = spi1_standard_cs,
.num_chipselect = ARRAY_SIZE(spi1_standard_cs),
},
};
void at91_add_device_spi(int spi_id, struct at91_spi_platform_data *pdata)
{
int i;
int cs_pin;
resource_size_t start = ~0;
BUG_ON(spi_id > 1);
if (!pdata)
pdata = &spi_pdata[spi_id];
for (i = 0; i < pdata->num_chipselect; i++) {
cs_pin = pdata->chipselect[i];
/* enable chip-select pin */
if (gpio_is_valid(cs_pin))
at91_set_gpio_output(cs_pin, 1);
}
/* Configure SPI bus(es) */
switch (spi_id) {
case 0:
start = AT91SAM9X5_BASE_SPI0;
at91_set_A_periph(AT91_PIN_PA11, 0); /* SPI0_MISO */
at91_set_A_periph(AT91_PIN_PA12, 0); /* SPI0_MOSI */
at91_set_A_periph(AT91_PIN_PA13, 0); /* SPI0_SPCK */
break;
case 1:
start = AT91SAM9X5_BASE_SPI1;
at91_set_B_periph(AT91_PIN_PA21, 0); /* SPI1_MISO */
at91_set_B_periph(AT91_PIN_PA22, 0); /* SPI1_MOSI */
at91_set_B_periph(AT91_PIN_PA23, 0); /* SPI1_SPCK */
break;
}
add_generic_device("atmel_spi", spi_id, NULL, start, SZ_16K,
IORESOURCE_MEM, pdata);
}
#else
void at91_add_device_spi(int spi_id, struct at91_spi_platform_data *pdata) {}
#endif
/* --------------------------------------------------------------------
* LCD Controller
* -------------------------------------------------------------------- */
#if defined(CONFIG_DRIVER_VIDEO_ATMEL_HLCD)
void __init at91_add_device_lcdc(struct atmel_lcdfb_platform_data *data)
{
BUG_ON(!data);
if (cpu_is_at91sam9g25() || cpu_is_at91sam9x25()) {
pr_warn("AT91: no lcd on at91sam9g25 or at91sam9x25\n");
return;
}
at91_set_A_periph(AT91_PIN_PC26, 0); /* LCDPWM */
at91_set_A_periph(AT91_PIN_PC27, 0); /* LCDVSYNC */
at91_set_A_periph(AT91_PIN_PC28, 0); /* LCDHSYNC */
at91_set_A_periph(AT91_PIN_PC24, 0); /* LCDDISP */
at91_set_A_periph(AT91_PIN_PC29, 0); /* LCDDEN */
at91_set_A_periph(AT91_PIN_PC30, 0); /* LCDPCK */
at91_set_A_periph(AT91_PIN_PC0, 0); /* LCDD0 */
at91_set_A_periph(AT91_PIN_PC1, 0); /* LCDD1 */
at91_set_A_periph(AT91_PIN_PC2, 0); /* LCDD2 */
at91_set_A_periph(AT91_PIN_PC3, 0); /* LCDD3 */
at91_set_A_periph(AT91_PIN_PC4, 0); /* LCDD4 */
at91_set_A_periph(AT91_PIN_PC5, 0); /* LCDD5 */
at91_set_A_periph(AT91_PIN_PC6, 0); /* LCDD6 */
at91_set_A_periph(AT91_PIN_PC7, 0); /* LCDD7 */
at91_set_A_periph(AT91_PIN_PC8, 0); /* LCDD8 */
at91_set_A_periph(AT91_PIN_PC9, 0); /* LCDD9 */
at91_set_A_periph(AT91_PIN_PC10, 0); /* LCDD10 */
at91_set_A_periph(AT91_PIN_PC11, 0); /* LCDD11 */
at91_set_A_periph(AT91_PIN_PC12, 0); /* LCDD12 */
at91_set_A_periph(AT91_PIN_PC13, 0); /* LCDD13 */
at91_set_A_periph(AT91_PIN_PC14, 0); /* LCDD14 */
at91_set_A_periph(AT91_PIN_PC15, 0); /* LCDD15 */
at91_set_A_periph(AT91_PIN_PC16, 0); /* LCDD16 */
at91_set_A_periph(AT91_PIN_PC17, 0); /* LCDD17 */
at91_set_A_periph(AT91_PIN_PC18, 0); /* LCDD18 */
at91_set_A_periph(AT91_PIN_PC19, 0); /* LCDD19 */
at91_set_A_periph(AT91_PIN_PC20, 0); /* LCDD20 */
at91_set_A_periph(AT91_PIN_PC21, 0); /* LCDD21 */
at91_set_A_periph(AT91_PIN_PC22, 0); /* LCDD22 */
at91_set_A_periph(AT91_PIN_PC23, 0); /* LCDD23 */
add_generic_device("atmel_hlcdfb", DEVICE_ID_SINGLE, NULL, AT91SAM9X5_BASE_LCDC, SZ_4K,
IORESOURCE_MEM, data);
}
#else
void __init at91_add_device_lcdc(struct atmel_lcdfb_platform_data *data) {}
#endif
/* --------------------------------------------------------------------
* UART
* -------------------------------------------------------------------- */
#if defined(CONFIG_DRIVER_SERIAL_ATMEL)
resource_size_t __init at91_configure_dbgu(void)
{
at91_set_A_periph(AT91_PIN_PA9, 0); /* DRXD */
at91_set_A_periph(AT91_PIN_PA10, 1); /* DTXD */
return AT91_BASE_SYS + AT91_DBGU;
}
resource_size_t __init at91_configure_usart0(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PA0, 1); /* TXD0 */
at91_set_A_periph(AT91_PIN_PA1, 0); /* RXD0 */
if (pins & ATMEL_UART_RTS)
at91_set_A_periph(AT91_PIN_PA2, 0); /* RTS0 */
if (pins & ATMEL_UART_CTS)
at91_set_A_periph(AT91_PIN_PA3, 0); /* CTS0 */
return AT91SAM9X5_BASE_USART0;
}
resource_size_t __init at91_configure_usart1(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PA5, 1); /* TXD1 */
at91_set_A_periph(AT91_PIN_PA6, 0); /* RXD1 */
if (pins & ATMEL_UART_RTS)
at91_set_C_periph(AT91_PIN_PC27, 0); /* RTS1 */
if (pins & ATMEL_UART_CTS)
at91_set_C_periph(AT91_PIN_PC28, 0); /* CTS1 */
return AT91SAM9X5_BASE_USART1;
}
resource_size_t __init at91_configure_usart2(unsigned pins)
{
at91_set_A_periph(AT91_PIN_PA7, 1); /* TXD2 */
at91_set_A_periph(AT91_PIN_PA8, 0); /* RXD2 */
if (pins & ATMEL_UART_RTS)
at91_set_B_periph(AT91_PIN_PB0, 0); /* RTS2 */
if (pins & ATMEL_UART_CTS)
at91_set_B_periph(AT91_PIN_PB1, 0); /* CTS2 */
return AT91SAM9X5_BASE_USART2;
}
resource_size_t __init at91_configure_usart3(unsigned pins)
{
at91_set_B_periph(AT91_PIN_PC22, 1); /* TXD3 */
at91_set_B_periph(AT91_PIN_PC23, 0); /* RXD3 */
if (pins & ATMEL_UART_RTS)
at91_set_B_periph(AT91_PIN_PC24, 0); /* RTS3 */
if (pins & ATMEL_UART_CTS)
at91_set_B_periph(AT91_PIN_PC25, 0); /* CTS3 */
return AT91SAM9X5_BASE_USART3;
}
#endif
