arch: add KBUILD_DEFCONFIG to allow "make defconfig" ...

Currently, "make defconfig" is only supported for sandbox and x86.

I set KBUILD_DEFCONFIG to support "make defconfig" where I was able
to find a suitable one.

nios2 and openrisc have a single generic_defconfig, so it is definitely
good for KBUILD_DEFCONFIG.

For arm, mips, I assume qemu is a preferred choice over a real board.

blackfin has only one defconfig. Since it is inactive (it is gone in
Linux), so no more defconfig will come in.

I am not sure about ppc and riscv, so I did not touch them.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/stm32'

Merge branch 'for-next/layerscape'

ARM: Makefile: restore kindle3 imxcfg-y setting ...

Commit 45f38c1a846f ("ARM: Makefile: Drop unnecessary imxcfg-y settings")
dropped the imximg generation for the kindle3. This device is not covered
within multiimage support and can be configured with kindle3_defconfig.

Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: Add basic Layerscape support ...

This adds basic Layerscape support:

- Makefile/Kconfig
- Register maps
- errata workarounds

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: Add initial STM32MP1 support ...

This adds initial STMicroelectronics MP1 support along with support
for the DK2 devel board. Only very basic support:

- UART
- SDRAM memory base/size
- No 1st stage support

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: Makefile: Drop unnecessary imxcfg-y settings ...

For boards built with multiimage support imxcfg-y is not needed.
Remove it for these boards.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/ultrascale'

ARM: CCMX51: Switch to multiimage support ...

This is a cumulative patch for the Digi ConnectCore CCMX51 SOM.
It includes:
- Switch board to devicetree probe.
- Add MMC update handler.
- Switch to multiimage support.
- Cleanup and optimize board code.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: zynqmp: add support for Xilinx ZCU104 board ...

Add support for the Xilinx Zynq Ultrascale+ MPSoC architecture (ZynqMP)
and the Xilinx ZCU104 board.

Barebox is booted as BL33 in EL-1 and expects that a BL2 (i.e. the FSBL)
already took care of initializing the RAM. Also for debug_ll, the UART
is expected to be already setup correctly. Thus, you have to add the
Barebox binary to a boot image as described in "Chapter 11: Boot and
Configuration" of "Zynq Ultrascale+ Device Technical Reference Manual".

Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: aarch64: compile with general-regs-only ...

Without this flag, gcc generates code to save the Q/V registers to the
stack for handling the va_list in pr_print(). Saving the registers is
useless, as the registers are never restored, but accessing the
registers to save them hangs the CPU.

Follow the Linux arch/arm64/Makefile and use the general-regs-only flag
to prevent usage of floating point and Advanced SIMD register.

Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/imx'

ARM: aarch64: disable 32bit boot commands ...

The 32bit boot support is full of legacy cruft. While it should be
possible to merge the aarch64 support there, a fresh start looks more
promising.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: aarch64: compile with strict alignment ...

barebox runs with MMU disabled at least during startup. We need
-mstrict-alignment for these parts to avoid alignment aborts.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX53/TX53: rework to dts based boot ...

Since nobody likes to use platformcode based machines any more, we also
switch this one to use dts based booting.

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: Add 64bit compilation alternative ...

Our 64bit file variants have the suffix "_64". This adds a make variable
that is either empty or contains "_64" which can be used to easily
alternatively compile the 32bit or 64bit variant.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: Makefile: format fix ...

Signed-off-by: Juergen Borleis <jbe@pengutronix.de>

arm: Add both .lds files to CLEAN_FILES unconditionally ...

'clean' target is listed on 'no-dot-config-targets' list in main
Makefile so that conditional statement would yeild the same result
every time. Given how CLEAN_FILES are rm'ed with -f there should be no
harm in specifying them both unconditionally.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

fix ARMv8 interference with ARMv7 ...

CONFIG_CPU_V8 is checked against 'y' and 'n', but the case when the
variable is unset is not considered.
This patch only checks the variable against a single value 'y' so the
logic is always coherent even when the variable is unset.

Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Tested-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX: pcm043: add a flash-header.imxcfg ...

This creates an image that can be booted via USB.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/imx'

ARM i.MX35: Add support for the Amazon Kindle3 ...

The Amazon Model No. D00901 Kindle3 is an E-Book reader based on the
i.MX35 SOC. The device boots in internal boot mode from a build-in eMMC,
alternatively the device may be set into USB-downloader mode when the
Vol+ key is pressed on startup.

Add support for this device and make barebox a drop-in replacement for
the factory shipped u-boot image.
Constraints for the use as drop-in replacement:
- imximg header (offset 0x400) has a maximum size of 2kB minus 16 byte
  since the last 16 bytes are used to store a vendor specific hardware
  desctription identifier
- the bootloader space (application plus env) is limited to 256kB minus
  16 bytes when installed with offset of 4kB (the u-boot offset was 3kB).
  A vendor specific device identifier is stored in the gap between
  application and kernel. The vendor specific identifiers should not
  be overwritten.

Notable features:
- Support for eMMC, USB, UART, I2C, SPI and Keys (except keyboard)
- Full support for vendor specific ATAGs
- usbserial barebox console access by pressing Select button at startup,
  alternatively full console support on connector J14.

Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

arm: boards: add mach-qemu and virt64 board ...

Introduce mach-qemu and add qemu virt64 board which emulates arm64 board.

Signed-off-by: Raphael Poggi <poggi.raph@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

arm: rework lib directory to support arm64 ...

This commit create a common directory, lib/,
for arm and arm64 common code.

It also create lib32/ and lib64/ for 32bit
and 64bit code respectively.

Signed-off-by: Raphael Poggi <poggi.raph@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

arm: Makefile: rework makefile to handle armv8 ...

Signed-off-by: Raphael Poggi <poggi.raph@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Make: i.MX: Allow to pass config file to cmd_imx_image ...

Pass the config file to cmd_imx_image as arguments to make it more
flexible. Also add the possibility for another arg containing additional
options.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

bcm2835: introduce mach-bcm283x ...

This patch changes the most part of mach-bcm2835 to mach-bcm283x. This
prepares to add RPi2 support which is a bcm2836. This patch changes the
Kconfig entry namens to BCM283X for drivers only. These drivers should
working the same in bcm2836.

While updating defconfig I added LED support/trigger option.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

arm: Disable unaligned accesses ...

From reading ARM architecture related documentation if appears that
while unaligned memory access is supported by the processor in general
it is not supported if MMU is disabled.

The problem in question can be easily reproduced by building the code
without this patch, MMU disabled, and trying to run 'memtest'
command. Which would in turn call mem_test() which would eventually
call show_progress(). That last function, if build without
-mno-unaligned-access would result in unaligned memory access which
would result in Barebox hanging.

This patch instructs the compiler to not generate any unaligned
accesses to memory thus avoiding the problem.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

arm: crypto: add sha1 assembly support ...

from Linux 3.9

linux generic implementation

$ ls -al build/versatilpb/arch/arm/pbl/zbarebox.bin
-rw-r--r-- 1 root root 210829 Mar 24 13:21 build/versatilpb/arch/arm/pbl/zbarebox.bin

linux arm v4 asm implementation
$ ls -al build/versatilpb/arch/arm/pbl/zbarebox.bin
-rw-r--r-- 1 root root 207786 Mar 24 13:23 build/versatilpb/arch/arm/pbl/zbarebox.bin

we win 3043 bytes and speed cf code

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/misc'