Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Most i.MX boards can use the imx*_barebox_entry functions. The remaining
(i.MX21, i.MX6) use hardcoded base addresses.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This adds support for initializing DDR3 RAMs on the i.MX53 type
SDRAM controller. The code automatically detects size/layout of
the connected RAM, detects the bus width and which chipselects are
populated.
While I believe this code is not 100% generic, it is far too
sophisticated to stay in a single board directory. I'm sure
other boards could make use of this aswell.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The code initializing the SDRAM controller is not at the same
place where SDRAM is registered with barebox. To reduce the
risk of registering wrong SDRAM sizes this patch adds a
driver for the ESDCTL which reads back the configured SDRAM
size and registers the memory found with barebox.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This adds support for an update handler for internal boot. Currently
handled are:

- v1 MMC/SD
- v2 MMC/SD
- v2 NAND

where v1 is found on i.MX25, i.MX35 and i.MX51. v2 is found on i.MX53.

This code intentionally does not use the DCD data compiled into every
i.MX internal boot image. This makes it possible to make a pure second
stage barebox bootable on i.MX internal boot devices later.

This has been tested on the i.MX51 babbage, i.MX53 loco and i.MX53 tx53
board.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The KARO Tx53 board in the revision 8030 has an instable SDRAM
setup. It works as long as the MMU is disabled, but the board
crashes at arbitrary places once the MMU gets enabled. So we
need the PLL setup early. Enable it for pbl.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Conflicts:
	arch/arm/mach-imx/imx1.c

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

- for i.MX1 the register is in the System Control unit, so move
  the code to arch/arm/mach-imx/imx1.c
- for the other i.MX the register is in the watchdog unit, so move
  the code to drivers/watchdog/imxwd.c

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

All i.MX SoCs now use the same imx_silicon_revision() function to get
the revision. Add a separate header file for it and a common function
used on all SoCs.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The old clock support is now unused. Remove it. The former i.MX clko
command is superseeded by generic clock manipulation commands.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This adds the basic i.MX common clk support and some pll and pfd
drivers.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add a function to take the usbphy1 through its initialization procedure.
The imx6_usb_phy1_disable_oc function is needed at least on the sabrelite,
as the power design is faulty. The state on other imx6 boards is unknown,
therefore it is an extra function call at the moment.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

With pbl support enabled most boards need a pbl-y for their lowlevel
stuff.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Because that's what it is.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Reimplement the code from lowlevel.S in C. It is run
from SDRAM anyway, so we can safely do this initialization
in a regular barebox environment instead in Assembly.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

- move code which can be shared between i.MX53 and i.MX51
  to a common file
- rename mx53_init_lowlevel to imx53_init_lowlevel

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The i.MX Processors support two different boot modes, the internal
boot mode and the external boot mode. Traditionally the external
NAND boot mode is handled in drivers/mtd/nand and the internal
boot mode is handled in arch/arm/mach-imx. This patch consolidates
the handling of both boot modes in arch/arm/mach-imx so that
the user does not have to look in the mtd kconfig section for
booting from NAND. Also, selecting between internal and external
boot mode now is a clear choice.
The external NAND boot mode has been independent of the mtd nand
driver, but as the code was contained in the NAND driver it was
not possible to support booting from NAND without a mtd nand driver.
This is changed with this patch.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>