ARM: Add i.MX6ull evk support ...

The i.MX6ull-EVK is a evaluation board for the i.MX6ull from NXP.
The upstream DTS is used, support should be fairly complete:

- 2x fec ethernet
- 1x USB Host
- 1x USB OTG
- 2x SD

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX: Add support for NXP i.MX7 SABRESD board ...

Add minimal code to support NXP i.MX7 SABRESD board. Tested to have
working SD card and first Ethernet port as well as being able to boot
upstream Linux kernel (4.12+).

Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>

ARM: imx: phyCORE i.MX7 on phyBOARD-Zeta support ...

This adds preliminary support for the phyCORE i.MX7 module on a
phyBOARD-Zeta baseboard. The DTs will likely change in the future
when PHYTEC finalizes their BSP.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>

ARM: mvebu: Add initial support for Turris Omnia ...

Up to now only 2nd stage booting is tested and boots up to a prompt.
i2c and spi are working, ethernet, usb and sata don't.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX6: add Technexion Pico Hobbit support ...

This adds support for the i.MX6UL Technexion Pico Hobbit. The board
comes with different amounts of RAM. We create one image for the 256MB
and one for the 512MB variant.

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
   ---
   v1 -> v2: - removed already prepared clock setup
   v2 -> v3: - added phy-reset-post-delay as the support is now available

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/socfpga'

ARM: socfpga: add support for reflex achilles board ...

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX50: Add support for i.MX50 based Amazon Kindle e-book readers ...

The Kindle Model No. D01100 (Kindle Wi-Fi), D01200 (Kindle Touch)
and EY21 (Kindle Paperwhite) are refered as the Kindle 4th and 5th generation.
Those models are based on an i.MX50 SoC and use LPDDR1 or LPDDR2 Memory.

The devices boot in internal boot mode from a build-in eMMC, alternatively
some devices may be set into USB-downloader mode by pressing a specific key
at startup.

Add support for the i.MX50 based Kindle device and make barebox a drop-in
replacement for the factory shipped u-boot image.

Notable features:
- Support for eMMC, USB, UART, I2C, SPI and Keys (except keyboard).
- LPDDR1 and LPDDR2 setup is done via DCD, the same imximage may be used
  for USB-startup and for installation.
- Support for vendor specific ATAGs that are required for the Kindle-System.
- usbserial barebox console access by pressing Select button at startup,
  alternatively full console support on connector J14.

Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX: vf610: Add support for ZII VF610 Dev Family ...

Add support for ZII VF610 Dev based designs such as:

    - VF610 Dev, revision B
    - VF610 Dev, revision C
    - CFU1, revision A
    - SPU3, revision A
    - SCU4 AIB, revision C

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX: Add WaRP7 board support ...

Signed-off-by Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: imx: Add support for ZII RDU2 board ...

Add support for RDU2 board from Zodiac Inflight Innovations.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX: Add support for VF610 Tower board ...

Add support for VF610 Tower board.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/mvebu'

ARM: mvebu: add support for Netgear RN2120 ...

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add support for Baltos systems ...

OnRISC Baltos devices are based on a am335x SoC and can be booted
either from MMC or NAND.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: Add phyCORE-RK3288 SOM support ...

The phyCORE-RK3288 aka PCM-059 is a SoM (System on Module)
containing a RK3288 SoC. The module can be connected to different
carrier boards.

Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: nitrogen: rename to nitrogen6 ...

Now that the MAX variant of the board is also supported by the
same code, rename the board directory to the more generic nitrogen6.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/imx'

ARM i.MX35: Add support for the Amazon Kindle3 ...

The Amazon Model No. D00901 Kindle3 is an E-Book reader based on the
i.MX35 SOC. The device boots in internal boot mode from a build-in eMMC,
alternatively the device may be set into USB-downloader mode when the
Vol+ key is pressed on startup.

Add support for this device and make barebox a drop-in replacement for
the factory shipped u-boot image.
Constraints for the use as drop-in replacement:
- imximg header (offset 0x400) has a maximum size of 2kB minus 16 byte
  since the last 16 bytes are used to store a vendor specific hardware
  desctription identifier
- the bootloader space (application plus env) is limited to 256kB minus
  16 bytes when installed with offset of 4kB (the u-boot offset was 3kB).
  A vendor specific device identifier is stored in the gap between
  application and kernel. The vendor specific identifiers should not
  be overwritten.

Notable features:
- Support for eMMC, USB, UART, I2C, SPI and Keys (except keyboard)
- Full support for vendor specific ATAGs
- usbserial barebox console access by pressing Select button at startup,
  alternatively full console support on connector J14.

Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

arm: boards: add mach-qemu and virt64 board ...

Introduce mach-qemu and add qemu virt64 board which emulates arm64 board.

Signed-off-by: Raphael Poggi <poggi.raph@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Terasic DE0-Nano-SoC: add support ...

v7: eof whitespace fixes

A Patch for supporting the Terasic DE0 NANO-SoC with barebox.
The pretty similar Socrates Board was taken as a starting point with pulling
in the memory timings/pinmux from
http://rocketboards.org/foswiki/view/Documentation/AtlasSoCCompileHardwareDesign

Signed-off-by: Tim Sander <tim@krieglstein.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add initial support for Netgear ReadyNAS 104 ...

Currently only second stage booting from the vendor U-Boot is tested. I
don't want to flash barebox into NAND yet because UART-booting for
recovery doesn't work for me.

Working so far are:

 - UART
 - networking
 - nand flash

Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

arm: bcm283x: add rpi2 support ...

This patch adds Raspberry Pi 2 support in barebox. The features should
be the same like the current RPi status in barebox.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: mx6sx-sabresdb: set proper hostname ...

Also move the initcall to the level matching the name of the
function.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

boards: Add phytec-som-imx6 ...

The main idea behind this patch is to avoid redundant code.  Because of
the module similarities of all i.MX6 based phytec boards, we can merge
its code.

The phytec-som-imx6 merges the code of all i.MX6 based phytec SOMs.  So
we will have only one "board" in the barebox for phyCARD-i.MX6 and
phyFLEX-i.MX6.

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX6: add Technexion Wandboard support ...

This adds support support for the i.MX6 Technexion Wandboard. The
board comes in different SoC variants and different amounts of RAM.
The baord type is autodetected based on the SoC type, so all boards
can be supported by the same binary image.

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: initial cm-fx6 support ...

The cm-fx6 board is a module from Compulab with different i.MX6 SoCs.
This module is also found in the Utilite Mini Computer this patch
also adds support for.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: mvebu: armada-xp: Add Lenovo Iomega ix4-300d ...

This adds support for Marvell Armada XP based 4-bay NAS Lenovo
Iomega ix4-300d.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/pxa'

ARM: pxa: add mainstone board support ...

Add support for the Intel XScale PXA270 development system platform.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>