Merge branch 'for-next/mtd'

Merge branch 'for-next/misc'

Merge branch 'for-next/arm'

reset: fix non GPIO reset ...

The reset controller structure is zero initialized in the OF
reset case, but as 0 is also a valid GPIO number the current
code tries to assert/deassert the GPIO instead of calling into
the reset controller device.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: chipidea-imx: check return value of regulator_get() ...

The VBUS regulator is optional for the chipidea-imx glue, so it must
be checked if regulator_get provided a valid regulator handle before
trying to enable the regulator.

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

PCI: imx6: properly shut down core when leaving barebox ...

As the i.MX6 PCIe core doesn't have a software reachable reset
wired up, it's hard for any driver to get the core into a known
good state.

To make it easier for whatever software follows barebox, bring
back the core into a safe state before leaving barebox.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX6: pci: Avoid aborts when asserting PCIe reset ...

When booting Barebox in the HW environment where PCIe core has been
used but not properly shut down, writing to PCIE_PL_PFLR in
imx6_pcie_assert_core_reset would cause data abort exception.

The problem can be easily reproduced on a i.MX6 based board with PCIe
slot populated with some device by doing:

> bootm -f -e 0x1050 <your board's>.img

Ignoring this exception seem to allow PCIe core to successfully
initialize and enumerate devices properly. This is also how Linux
Kernel version of the driver handles this situation -- it installs
dummy no-op abort handler at the beginning of device's probing.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX6: pci: Reconcile imx6_pcie_start_link with the kernel code ...

Reconcile imx6_pcie_start_link with almost identical
imx6_pcie_establish_link from analogous Linux kernel driver. This
change is purely cosmetical, but refactoring the code this way
simplifies implementation comparison.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX6: pci: Replace magic number with a named constant ...

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

of_path: Drop possible further extensions of device-path property ...

Originally it was intended to further extend the multi string property
device-path further with more elements, like for example a filename. It
turned out though that this is too complex and instead of further
extending the property we should instead create additional properties,
so this mechanism is removed with this patch to make the code simpler.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

environment: Support env from file in a file-system via device tree ...

Current barebox,environment node only allows specifying a raw device or
partition to load an environment from.  Some boards, like OMAP and
SoCFPGA, instead want to use a file located in a FAT filesystem.
Extend the device tree bindings with a new property 'file-path' that
will trigger this behavior.

This allows any board using this driver to get the env from a file or
from a raw device, instead of each machine type being either raw
device only or file only.

Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

input: gpio-keys: implement debouncing ...

The gpio-keys driver often generates multiple events on a single buttong
press. Implement debouncing. The default debouncing time is 20ms and can
be configured with the "debounce-interval" device tree property.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

of_path: Fix bug with partitions, simply code ...

In commit 75b6827 using a path that
has a partition description broke.

Fix this and simpfy the code some.

There is no need to loop over each string in the path property:  it's
defined to have at most one parition description, no extant dts has
more than one, and how it would handle more than one didn't make sense
anyway.

Once not looping, __of_find_path() just needs the partition
description text, not both the original node and property name to look
it up from.

When using a partition description, don't lookup the cdev of the node
just to replace it with the partition's cdev.

Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mtd: gpmi: Add erased page bitflip correction ...

Hardware ECC does not work for erased pages. However as soon as
something that is not 0xff is found in the page, hardware ECC assumes
this is valid data and produces an uncorrectable error ECC status. We
can use that to check for bitflips in erased pages and fix them if the
number of flipped bits is below the ecc_strength.

We need to move the memcpy above the for loop to be able to access the
buffer directly.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mtd: nand: Add erased page bitflip check helper functions ...

This adds the bitflip check helper functions from the kernel. They are
used to check for bitflips in erased pages and correct them in the
buffer so that UBI can work with it. Unfortunately most nand controllers
do not have ECC for erased pages and don't do this on their own.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

bcm2835: introduce mach-bcm283x ...

This patch changes the most part of mach-bcm2835 to mach-bcm283x. This
prepares to add RPi2 support which is a bcm2836. This patch changes the
Kconfig entry namens to BCM283X for drivers only. These drivers should
working the same in bcm2836.

While updating defconfig I added LED support/trigger option.

Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

MCI: init device_node for MCI mainarea cdev ...

This fixes a regression, where boards specifying the environment
path using the form device-path = &phandle, "partname:part" would
be unable to find their env.

This is due to of_find_path() switching to cdev_by_device_node()
internally, which expects the device_node member of the main
area cdev to be initialized.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/state'

Merge branch 'for-next/socfpga'

Merge branch 'for-next/reset'

Merge branch 'for-next/omap'

Merge branch 'for-next/net'

Merge branch 'for-next/mtd'

Merge branch 'for-next/mmc'

Merge branch 'for-next/mips'

Merge branch 'for-next/imx'

Merge branch 'for-next/i2c'

Merge branch 'for-next/fb'

drivers: bus: Match against id_table first ...

Matching against driver's name before looking throught its id_table
can lead to a somewhat strange and unintuitive behaviour where a
device whose driver's name matches one of the lines in id_table (which
is not unheard of in Linux kernel) will be probed against said driver
with 'id_table' field set to NULL which in turn will result in
dev_get_drvdata erroring out with -ENODEV.

This patch changes the behaviour such that device_match() only tries
to match against driver's name only if id_table of that driver is not
present.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: smc1111: fix ethernet mac setting ...

Even if the setting of the MAC address does work correctly, the function
return an error.

In the former barebox version, this didn't seem to be a problem. In
v2015.11.0 version, the "ifup eth0" command fails because of this, and
as a consequence the network interface doesn't work.

The fix is straightforward.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>