The headerfile is used in the kernel for access of MDIO Managed Devices
(MMD) indirect access. Some drivers already use those device addresses.
We add the headerfile from the kernel and change the current users to
use the defines instead

Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

this patch will allow to use proper clock skew configuration from
devicetree instead of using board specific fixups.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This patch backports linux commit e1b505a60366 ("net: phy: micrel: add
125MHz reference clock workaround").

8<--------------------- The original commit message -------------------

net: phy: micrel: add 125MHz reference clock workaround

The micrel KSZ9031 phy has a optional clock pin (CLK125_NDO) which can be
used as reference clock for the MAC unit. The clock signal must meet the
RGMII requirements to ensure the correct data transmission between the
MAC and the PHY. The KSZ9031 phy does not fulfill the duty cycle
requirement if the phy is configured as slave. For a complete
describtion look at the errata sheets: DS80000691D or DS80000692D.

The errata sheet recommends to force the phy into master mode whenever
there is a 1000Base-T link-up as work around. Only set the
"micrel,force-master" property if you use the phy reference clock provided
by CLK125_NDO pin as MAC reference clock in your application.

Attenation, this workaround is only usable if the link partner can
be configured to slave mode for 1000Base-T.

Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
[m.felsch@pengutronix.de: fix dt-binding documentation]
[m.felsch@pengutronix.de: use already existing result var for read/write]
[m.felsch@pengutronix.de: add error handling]
[m.felsch@pengutronix.de: add more comments]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
8<---------------------------------------------------------------------

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Reviewed-by: Roland Hieber <r.hieber@pengutronix.de>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Since commit a4cee7207a1 ("net: phy: micrel: Add workaround for bad
autoneg") by Philipp Zabel <p.zabel@pengutronix.de>:

    Based on kernel commit d2fd719bcb0e ("net/phy: micrel: Add workaround
    for bad autoneg") by Nathan Sullivan <nathan.sullivan@ni.com>:

        Very rarely, the KSZ9031 will appear to complete autonegotiation, but
        will drop all traffic afterwards.  When this happens, the idle error
        count will read 0xFF after autonegotiation completes. Reset the PHY
        when in that state.

is it possible that we get the link to late and  barebox reports "Network is
down". The problem is that ksz9031_config_init is called again in an
error case. In this case autoneg will restart but waiting for finish is
missing.

Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Tested-by: Stefan Müller-Klieser <s.mueller-klieser@phytec.de>

ksz8021_config_init() unconditionally sets the KSZPHY_OMSO_RMII_OVERRIDE
bit. This is since the initial micrel phy commit, so it's not
reproducible where this comes from and why this is done. Neither U-Boot
nor the kernel ever touch this bit and so should we. Also, instead
of doing a write only operation, read/modify/write the bit we actually
want to change.
This fixes operation on a KSZ8081MLX which is a MII only phy.
KSZPHY_OMSO_RMII_OVERRIDE is reserved here and must be written to 0.
KSZPHY_OMSO_MII_OVERRIDE is default 1 and must be written as 1.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

KSZ9081 only supports two phy ids 0x0 and 0x3. 0x0 is also
used as broadcast address. Disable broadcast, so that id 0x0
can be used as unique address on a shared bus.

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Based on kernel commit d2fd719bcb0e ("net/phy: micrel: Add workaround
for bad autoneg") by Nathan Sullivan <nathan.sullivan@ni.com>:

    Very rarely, the KSZ9031 will appear to complete autonegotiation, but
    will drop all traffic afterwards.  When this happens, the idle error
    count will read 0xFF after autonegotiation completes.  Reset the PHY
    when in that state.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Based on kernel commit 6270e1ae804a ("net/phy: micrel: Center FLP
timing at 16ms") by Jaeden Amero <jaeden.amero@ni.com>:

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Based on kernel commit 3c9a9f7fb0ee ("net/phy: micrel: Be more const
correct") by Jaeden Amero <jaeden.amero@ni.com>:

    In a few places in this driver, we weren't using const where we could
    have. Use const more.

    In addition, change the arrays of strings in ksz9031_config_init() to be
    not only const, but also static.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Based on kernel commit 00aee095000c ("net: phy: micrel: use BIT macro")
by Johan Hovold <johan@kernel.org>.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Based on kernel commit 32d73b144eac ("net: phy: micrel: Staticise
ksz8873mll_read_status()") by Jingoo Han <jg1.han@samsung.com>:

    ksz8873mll_read_status() is used only in this file.
    Fix the following sparse warning:

    drivers/net/phy/micrel.c:147:5: warning: symbol 'ksz8873mll_read_status' was not declared. Should it be static?

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Adds support for ksz9031 PAD skew configuration over devicetree.
Based on a patch from the linux kernel.

Author: Hubert Chaumette <hchaumette@adeneo-embedded.com>
Original commit: 6e4b827

Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

With SUPPORTED_Asym_Pause enabled we need to hotplug the ethernet cable.
So disable it like done with PHY_ID_KSZ9021.

Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

KSZ8031 is similar to KSZ8021. It can use the same functions.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Due to a hw bug do not enable teh Asym_Pause.
Otherwise if you ser the bit 11 in 4h you will have to unplug
and replug the cable to make the phy work.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>