treewide: remove references to CREDITS ...

The CREDITS file was removed from barebox in 2015 by commit 6570288f2d97
("Remove the CREDITS file"). Remove references to it from several files.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: core: use SECTOR_SIZE instead of direct 512 ...

Instead of hardcoding the 512 byte constant, use the symbolic
SECTOR_SIZE.

Signed-off-by: Ahmad Fatoum <ahmad@a3f.at>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/parameter'

mci: core: populate mci_ios.timing member ...

So far we passed an uninitialized timing member in the ios to the
->set_ios of the host controller drivers.

To allow extension for new modes that need MCI host support beyond
the usual clock rate change, make the member useful:

- populate is with the correct value
- add some type safety by using an enum
- print it in the devinfo output

Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: core: don't test 4-bit-buswidth support if MMC host lacks capability ...

We already check for MMC_CAP_8_BIT_DATA before trying if buswidth=8
yields legible data. For consistency, don't test whether buswidth=4
works if the MMC host doesn't indicated MMC_CAP_4_BIT_DATA.

Fixes: 68db956d ("mci: Fix 8 bit mmc cards")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: remove param_probe member from struct mci ...

After adding the parameter, the pointer isn't required anymore.

Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Revert "mci: core: make mci_register -EPROBE_DEFER sensitive" ...

The patch does the right thing: When a regulator can't be found and
-EPROBE_DEFER is returned we forward it. However, we have several boards
in the tree which do not have any driver for the regulator, but still
work because the regulator is enabled by default or by board code.

Revert this patch until a solution for these board is found.

This reverts commit 2e16c52.

mci: core: make mci_register -EPROBE_DEFER sensitive ...

If the current regulator can't be requested because of -EPROBE_DEFER we
shouldn't print a error and ignore it.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/mmc'

mci: skip of_partitions_register_fixup for boot partitions ...

The bootN-partitions binding is barebox-specific, so it shouldn't
be fixed up into the kernel device tree.

Suggested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: Rely on NULL being a dummy regulator ...

Since NULL, is a dummy regulator, we can drop a bit of error checking
logic and simplify the code if we assing host->supply to NULL in case
we can't find an appropriate regulator during probing.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: core: Use alias as a devname by default ...

This idiom is repeatead by almost every mci driver, so move it to
mci_of_parse() in order to reduce amount of duplicated code.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

drivers: Introduce dev_set_name() ...

Introduce dev_set_name() in order to hide implementation details of
setting device's name so it'd be easier to change it.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: drop unused parameter from mci_switch() ...

The SWITCH command has two purposes:
 a) switch the command set
 b) Write to the EXT_CSD register

If the access field (bits [25:24]) in the argument are b00, we're in
case a), otherwise in b). As mci_switch() always passes
MMC_SWITCH_MODE_WRITE_BYTE (0b3) in the access field, only case b) is
relevant here. According to the eMMC specification[1] the command set
field is ignored in case b) and so the respective parameter (that is
unused already now) can be dropped.

[1] Embedded Multi-Media Card (e•MMC) Electrical Standard (5.1),
    February 2015; paragraph 6.6.1

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mmc: allow skipping SD card initialization ...

This patch allows to skip SD card initialization for eMMCs by setting
the "no-sd" property in the host controller device tree node. Avoiding
two SD command timeouts speeds up detection time by well over 200 ms.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mmc: add eMMC v5 and V5.1 detection support ...

Just add the defines.

Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>

mmc: Consistently use EXT_CSD_* names from eMMC 5.1 spec ...

We have kept the EXT_CSD registers which were added in the 5.1 spec
separately for no good reason. Order the EXT_CSD defines by register
number instead. Also we had some duplicates, for these consistently
use the names from the 5.1 spec.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>

mci: be more verbose about wrong bus-width ...

If configured or default bus-width is wrong for the current hardware,
registration of card/emmc is likely to fail.  This patch adds more verbosity
in the case of a failed detection:

    | omap-hsmmc 48060000.mmc: registered as 48060000.mmc
    | mmc0: detected MMC card version 4.41
    | mmc0: Changing MMC bus width failed: -110
    | mmc0: Card's startup fails with -110

Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/ofpart'

of: partition: Register the of partition fixup for of partition users ...

at24, at25 and mci core are using of_parse_partitions(). Register the
fixup for them aswell.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: Allow parsing for explicit DT node ...

Convert mci_of_parse into mci_of_parse_node, a function that takes
explicit deivce tree node pointer to be used for SD/MMC related
properties extraction. Implement original mci_of_parse as a wrapper
around the call to new function.

This is useful for controllers who specify parameter like bus witdth and
GPIOs as a part of main controller's child nodes (e.g. AT91 SoCs).

Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: Allow to partition eMMC boot partitions ...

So far the eMMC boot partitions cannot be partitioned from the
device tree. Since they are often 4MiB in size they are big enough
to hold a barebox image and the environment. Add partition parsing
to the boot partitions to allow this usecase.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: core: Do not fail if vmmc regulator fail ...

The vmmc regulator can be an usupported device for barebox,
the specific MFD regulator type, for example. Just lets think is all ok.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: Fix version numbers again ...

The SD and eMMC version numbers are a pain to print and sort, since
they are inconsistent in if a two digit minor version shdoulde be
treated as a single number or as minor and micro version numbers.

This allows version 1.10 and 4.5 and 4.41, where 41 is less than 5.

Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

string: Fix (v)asprintf prototypes ...

Our asprintf and vasprintf have different prototypes than the glibc
functions. This causes trouble when we want to share barebox code
with userspace code. Change the prototypes for (v)asprintf to match
the glibc prototypes. Since the current (v)asprintf are convenient
to use change the existing functions to b(v)asprintf.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

MCI: init device_node for MCI mainarea cdev ...

This fixes a regression, where boards specifying the environment
path using the form device-path = &phandle, "partname:part" would
be unable to find their env.

This is due to of_find_path() switching to cdev_by_device_node()
internally, which expects the device_node member of the main
area cdev to be initialized.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: core: bus-width property should override driver default ...

The OF code for parsing bus-width would only add the specified width
to those the driver might have already set capability flags for.

Because of this, if the driver had set 8 or 4 bit width, it wasn't
possible for the DT to specify that fewer pins were used on the board
and a smaller width was necessary.

Change this so the width in the DT overrides whatever widths the
driver says it supports.  There is no reason to have an incorrect
device tree and it makes far more sense for the DT to override the
driver default than for the driver default to override the DT.

The widths the driver puts in host_caps before calling mci_of_parse()
are considered the default if the DT doesn't specify bus-width.  This
should cause the least amount of change to existing boards, as despite
a comment that no bus-width meant to use 1 bit, using the driver
default is what was really happening.

Unfortunately, half of existing drivers default to the largest width
they support while the other half default to the smallest.  Boards
should just stick the width in the device tree.

Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: Print versions with micro levels correctly ...

The version is stored as BCD, e.g. 0x40 -> ".4" and 0x41 -> ".41".
The latter was getting printed as ".65".  Simplify the logic a bit to
not split the minor into nybbles just to re-assemble it into a byte
again.

Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: core: Increase clock for SD highspeed mode ...

Putting a SD card into highspeed mode doesn't help much when we
still clock the card with 25MHz. Increase the clock speed to 50MHz
for high speed cards.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

drivers: mci: Add mci_get_device_by_name function ...

Get a 'struct mci' by search after the device name.

Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>