arm: dts: Fix node names ...

- Remove leading zeroes from the addresses in the node names of i2c/spi
  devices
- Remove leading 0x from the addresses in the node names of i2c/spi
  devices
- Add missing reg address in node names.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: dts: use stdout-path property ...

linx,stdout-path has been deprecated. Use stdout-path instead.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX53 Vincell: change dialog compatible to proper vendor prefix ...

The compatible vendor prefix for dialog pmic is dlg. We fix it in
the devicetrees using the wrong one.

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX53 Vincell: Reset phy consistently from device tree ...

The phy reset for the Vincell board is done from device tree whereas
the Vincell-LT resets the phy from board init code. Since both boards
share the same code base the regular Vincell board ends up with a
duplicated phy reset, with the second reset being done after the
FEC has been initialized.
Fix this by removing the phy reset from the board code and adding the
phy reset to the Vincell-LT dts file.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX: increase barebox partition sizes ...

After doing a 'saveenv' command, it is no longer possible to boot.

The reason for this behaviour is that the 'barebox' partition has
currently
a size of 0x80000 (512 kB), which is not sufficient to store the barebox
binary. This causes the 'barebox' and 'barebox-environment' partitions
to overlap.

Fix this problem by increasing the size of the 'barebox' partition and
by placing the 'barebox-environment' right after it.

This patch increases the barebox partition for all i.MX boards to
0xe0000

Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: dts: Fix partition names ...

Partition names shouldn't be continuously numbered, instead the part
behind the '@' should match the reg property. Fix this for all ARM
device trees.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>

arm: imx53-guf-vincell-lt: dts: do not specfiy fixed memory information ...

Setting a fixed memory size prevents from using the different board
variants with different memories equipped.

barebox is able to read RAM size informations from the imx53 RAM
controller and thus does not require this information passed via dts.

Signed-off-by: Enrico Jorns <ejo@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: vincell: move to DT probing ...

This enabled multi image support for the Garz&Fricke Vincell board. Also
it adds the Vincell-LT as a second image with a separate device tree.
Previously we used the same image on both the Vincell and the Vincell-LT
image since the differences are not that significant for barebox. Still
this was good for quite some confusion internally, so let's properly
introduce a second image.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>