Currently it's hardcoded for each board which defaultenv version is
used. This is unfortunate since some people like the other defaultenv
version better and may want to select it.

This patch removes the board specific environment path
CONFIG_DEFAULT_ENVIRONMENT_PATH and instead adds it via:

	if (IS_ENABLED(CONFIG_DEFAULT_ENVIRONMENT_GENERIC))
		defaultenv_append_directory(defaultenv_<board>);

This way we can make sure that the defaultenv-1 board specific bits are
only compiled in when defaultenv-1 is actually in use.

The next step is to make the defaultenv version selection a user visible
choice.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The current implementation fakes a memory-mapped I/O device
at 0x3f8 and 0x2f8, then uses platform read/write functions
to do the actual reading and writing. These platform functions
only exist for the x86 platform; better to move the I/O
routines into the driver and have the driver request I/O ports
using request_ioport_region.

Signed-off-by: Michel Stam <michel@reverze.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add an environment partition and support commands so that the system
configuration can be permanent.

Signed-off-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

With multiboard support the compiletime generated BOARDINFO string
gets more and more meaningless. This removes it from Kconfig and
replaces it with a variable that can be set at boardlevel.

Also many boards have a standard setting for the hostname in the
environment. This patch also moves the standard to C code by calling
barebox_set_hostname().

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The chip select 0 (boot flash) registers are updated by the board
specific code as it is not done by the cpu early initialisation
any more.

Signed-off-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This commit creates MDIO bus devices to separate the MDIO bus
abstraction from the Ethernet device initialisation.

It also updates the configuration of the P2020RDB ports.

Signed-off-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The FSF address has changed in the past. Instead of updating it
each time the address changes, just drop it completely treewide.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Conflicts:
	arch/ppc/boards/freescale-p2020rdb/p2020rdb.c
	arch/ppc/configs/p2020rdb_defconfig
	arch/ppc/mach-mpc85xx/include/mach/immap_85xx.h

Support for both i2c busses on the p2020rdb board is added and the
configuration file is updated to add the I2C driver and commands.

Signed-off-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

In order to use the IMX i2c driver on the mpc85xx SOC, the file mach/clocks.h
is renamed mach/clock.h. Files using this header are updated accordingly.

Signed-off-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Minimal support of the Ethernet interface on the P2020RDB board. Only
the eTSEC3 interface is supported.

Signed-off-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This is limited board support for the Freescale P2020RDB in single CPU
mode. The DDR is configured for a memory bus running at 667Mhz.
The system boots from NOR flash and provides the console at 115200
bauds, no other drivers are included.

Finally, the PPC Kconfig and make file make the building of
the P2020RDB platform firmware possible.

Signed-off-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>