LuminaSensum/barebox

Fork: 0

LuminaSensum / barebox

History for barebox / arch

2015-07-02	b8b0a7f Browse files » ARM: start: Fix code reordering problem ... This adds a barrier after setup_c(). This is necessary because otherwise some global variable assignments may be reordered by the compiler to be executed before setup_c which cannot work. This was observed when doing other unrelated changes to the start function, it seems in current mainline state the compiler does not actually reorder the code. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Sascha Hauer committed on 2 Jul 2015
2015-07-01	fc6cb7a Browse files » mx53-qsb: Fix boot hang during reboot stress test ... Fix the DDR init sequence the same way as done by aee0013e53b339a5 from U-boot in order to prevent the boot hang under reboot stress test. Quoting this commit log: "Currently by running the following test: => setenv bootcmd reset => save => reset , we observe a hang after approximately 20-30 minutes of stress reboot test. Investigation of this issue revealed that when a single DDR chip select is used, the hang does not happen. It only happens when the two chip selects are active. MX53 reference manual states at "28.6.2 Memory ZQ calibration sequence": "The controller must keep the memory lines quiet (except for CK) for the ZQ calibration time as defined in the Jedec (512 cycles for ZQCL after reset, 256 for other ZQCL and 64 for ZQCS)." According to the SDE_0 and SDE_1 bit descriptions from register ESDCTL_ESDCTL: "Writing 1 to SDE0 or SDE1 will initiate power up delays as JEDEC defines. Power up delays are a function of the configured memory type (DDR2/DDR3/LPDDR2)" So make sure to activate one chip select at time (CS0 first and then CS1 later), so that the required JEDEC delay is respected for each chip select. With this change applied the board has gone through three days of reboot stress test without any hang." Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Fabio Estevam authored on 29 Jun 2015 Sascha Hauer committed on 1 Jul 2015
2015-06-09	e349701 Browse files » Merge branch 'for-next/state' Sascha Hauer committed on 9 Jun 2015
	3a32e7a Browse files » Merge branch 'for-next/spi-nor' Sascha Hauer committed on 9 Jun 2015
	61c7946 Browse files » Merge branch 'for-next/socfpga' Sascha Hauer committed on 9 Jun 2015
	03510ac Browse files » Merge branch 'for-next/posix_types' Sascha Hauer committed on 9 Jun 2015
	7a429bf Browse files » Merge branch 'for-next/misc' Sascha Hauer committed on 9 Jun 2015
	760e652 Browse files » Merge branch 'for-next/mips' Sascha Hauer committed on 9 Jun 2015
	780c5c8 Browse files » Merge branch 'for-next/imx' Sascha Hauer committed on 9 Jun 2015
	ee2ac17 Browse files » Merge branch 'for-next/am33xx' Sascha Hauer committed on 9 Jun 2015
2015-06-05	0b06cf7 Browse files » ARM: am33xx: Add network boot ... Signed-off-by: Wadim Egorov <w.egorov@phytec.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Wadim Egorov authored on 3 Jun 2015 Sascha Hauer committed on 5 Jun 2015
2015-06-04	866cb8e Browse files » PPC: asm/bitops.h: drop unused ext2* and minix* stuff ... Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Antony Pavlov authored on 3 Jun 2015 Sascha Hauer committed on 4 Jun 2015
2015-06-04	5b19507 Browse files » MIPS: asm/debug_ll_ns16550.h: use plain inline instead of __inline__ ... Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Antony Pavlov authored on 3 Jun 2015 Sascha Hauer committed on 4 Jun 2015
2015-06-03	291c7e9 Browse files » ARM: imx6: hipercam: set default hostname in boardfile ... Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Lucas Stach authored on 1 Jun 2015 Sascha Hauer committed on 3 Jun 2015
	47f46a0 Browse files » ARM: imx6: correct Hipercam ECSPI1 pinmux ... Correct the pinmux configuration for the chip-select GPIOs. This fixes detection of the first SPI NOR-flash after barebox itself got loaded from there. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Lucas Stach authored on 1 Jun 2015 Sascha Hauer committed on 3 Jun 2015
	a479098 Browse files » nios2: use generic posix_types.h ... Use generic asm-generic/posix_types.h instead of repeating the typedefs. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Sascha Hauer committed on 3 Jun 2015
	79e3eda Browse files » efi: use generic posix_types.h ... Use generic asm-generic/posix_types.h instead of repeating the typedefs. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Sascha Hauer committed on 3 Jun 2015
	e2d767c Browse files » sandbox: use generic posix_types.h ... Use generic asm-generic/posix_types.h instead of repeating the typedefs. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Sascha Hauer committed on 3 Jun 2015
	f7eb11d Browse files » ppc: use generic posix_types.h ... Use generic asm-generic/posix_types.h instead of repeating the typedefs. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Sascha Hauer committed on 3 Jun 2015
	567bdd5 Browse files » mips: use generic posix_types.h ... Use generic asm-generic/posix_types.h instead of repeating the typedefs. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Sascha Hauer committed on 3 Jun 2015
	5c7d1e1 Browse files » openrisc: use generic posix_types.h ... Use generic asm-generic/posix_types.h instead of repeating the typedefs. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Sascha Hauer committed on 3 Jun 2015
	de8739b Browse files » x86: use generic posix_types.h ... Use generic asm-generic/posix_types.h instead of repeating the typedefs. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Sascha Hauer committed on 3 Jun 2015
	e4f60ca Browse files » blackfin: use generic posix_types.h ... Use generic asm-generic/posix_types.h instead of repeating the typedefs. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Sascha Hauer committed on 3 Jun 2015
	3ce9610 Browse files » ARM: use generic posix_types.h ... Use generic asm-generic/posix_types.h instead of repeating the typedefs. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Sascha Hauer committed on 3 Jun 2015
	e4daf80 Browse files » introduce bitsperlong.h for remaining architectures ... This introduces the bitsperlong.h file for the remaining architectures. It's purpose is to define BITS_PER_LONG which in the next step can be used by a generic posix_types.h file. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Sascha Hauer committed on 3 Jun 2015
2015-05-29	1849bfb Browse files » ARM: socfpga: xload: support qspi bootsource ... Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Steffen Trumtrar authored on 28 May 2015 Sascha Hauer committed on 29 May 2015
	d96a467 Browse files » ARM: socfpga: sockit: add qspi flash ... Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Steffen Trumtrar authored on 28 May 2015 Sascha Hauer committed on 29 May 2015
	72dbaa5 Browse files » ARM: socfpga: socrates: add qspi flash ... Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Steffen Trumtrar authored on 28 May 2015 Sascha Hauer committed on 29 May 2015
	43fa203 Browse files » ARM: socfpga: socdk add qspi flash ... Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Steffen Trumtrar authored on 28 May 2015 Sascha Hauer committed on 29 May 2015
	b9430c2 Browse files » ARM: dts: socfpga: add qspi node ... Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Steffen Trumtrar authored on 28 May 2015 Sascha Hauer committed on 29 May 2015