ARM: mx6sx-sabresdb: set proper hostname ...

Also move the initcall to the level matching the name of the
function.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: imx6dl: Add support for Phytec phyCORE-i.MX6 SOM ...

Add Phytec phyCORE-i.MX6 SOM.
     - imx6dl-phytec-phycore-som-nand
        - 256GB RAM on 1 Bank with 32Bit
        - 10/100MBit Ethernet
        - NAND
        - SD
        - UART

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: imx6q: Add support for Phytec phyCORE-i.MX6 SOM ...

Add Phytec phyCORE-i.MX6 SOM.
    Support:
     - imx6q-phytec-phycore-som-nand:
        - 1GB RAM on 1 Bank with 64Bit
        - 1GBit Ethernet
        - SPI NOR
        - NAND
        - SD
        - UART

     - imx6q-phytec-phycore-som-emmc
        - 1GB RAM on 1 Bank with 64Bit
        - 1GBit Ethernet
        - SPI NOR
        - eMMC
        - SD
        - UART

Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: imx6q: pfla02: add phyFLEX-i.MX6 DualLite 1GiB on one bank ...

Add support for phyFLEX-i.MX6 DualLite 1GiB on one bank with NOR.

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: imx6dl: pfla02: Add support for 128MB and 256MB RAM ...

Add support for phyFLEX-i.MX6 Solo with 128MB and 256MB RAM on one
memory bank.

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: imx6q: pfla02: Add support for 512MiB RAM on one bank ...

Add support for phyFLEX-i.MX6 Quad 512MiB RAM on one bank.

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: pfla02: append suffix 1bank ...

In the current naming schema the phyFLEX-i.MX6 variants which only use
one bank for memory have the suffix "1bank". The variants which use two
banks of memory have no suffix.

The patch fixes the name of the phyFLEX-i.MX6 Solo variant with 512MiB
on one bank. So the name of the image file changes from
    barebox-phytec-pbab01s-512mb.img
    barebox-phytec-phyboard-subra-512mb.img
to
    barebox-phytec-pbab01s-512mb-1bank.img
    barebox-phytec-phyboard-subra-512mb-1bank.img

This patch touches the phyFLEX-i.MX6 Kit variant and the
phyBOARD-SUBRA-i.MX6 which shares the same phyFLEX-i.MX6 module.

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

boards: Add phytec-som-imx6 ...

The main idea behind this patch is to avoid redundant code.  Because of
the module similarities of all i.MX6 based phytec boards, we can merge
its code.

The phytec-som-imx6 merges the code of all i.MX6 based phytec SOMs.  So
we will have only one "board" in the barebox for phyCARD-i.MX6 and
phyFLEX-i.MX6.

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: microsom: add full set of module variants on Hummingboard ...

Now that we have a full set of DRAM configuration entries we can
build images for the full set of modules on Hummingboard.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: microsom: import DCD from SolidRun U-Boot ...

This is a complete set of DRAM configuration values for all of the
MicroSOM variants extracted from SolidRun U-Boot.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: microsom: change barebox image name for Hummingboard ...

To reflect that the current image is in fact for a combination of a
MicroSOM i1 with a Hummingboard baseboard.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

images: Embedsky E9: use image name like the rest of boards ...

Use name similar to other boards thus remove freescale from image
name since this is not a Freescale board, move SoC type after
company name.

So image name changed from barebox-freescale-imx6q-embedsky-e9.img to
barebox-embedsky-imx6q-e9.img

Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX6: add Technexion Wandboard support ...

This adds support support for the i.MX6 Technexion Wandboard. The
board comes in different SoC variants and different amounts of RAM.
The baord type is autodetected based on the SoC type, so all boards
can be supported by the same binary image.

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/vincell'

ARM: initial cm-fx6 support ...

The cm-fx6 board is a module from Compulab with different i.MX6 SoCs.
This module is also found in the Utilite Mini Computer this patch
also adds support for.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

images: i.MX: Create target for SRAM images ...

Some boards like to do their SDRAM setup in code rather than in hardcoded
DCD tables. For these boards the bootloader has to be loaded to the internal
SRAM which is often too small for a full featured barebox. This new SRAM
image type target allows to overcome this limitation. The image created
with the new imx-sram-img rule is a regular imx-image with the difference
that the load size only spans the pblx image and not the whole image including
the payload. The pbl image easily fits into SRAM. The strategy is that this
initial code initializes the SDRAM, loads the whole image to SDRAM and jumps
to it.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: vincell: move to DT probing ...

This enabled multi image support for the Garz&Fricke Vincell board. Also
it adds the Vincell-LT as a second image with a separate device tree.
Previously we used the same image on both the Vincell and the Vincell-LT
image since the differences are not that significant for barebox. Still
this was good for quite some confusion internally, so let's properly
introduce a second image.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX: Add provisions to boot from IRAM ...

This commit add a very basic code to allow Barebox to be booted from
IRAM. Given that the amount of IRAM on most i.MX variants is
insufficient to contain a copy of Barebox with any reasonable degree
of functionality this code uses IRAM only as a temporary location and
eventually bootstraps from DRAM. But the presense of the intermediate
IRAM-only stage allows to add provisions to test the area of DRAM that
Barebox would be using to facilitate various testing scenarious.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/misc'

ARM: Add ELTEC HiPerCam board support ...

This adds support for the i.MX6 based Eltec HiPerCam board.
This board comes with different i.MX6 flavours and different
memory sizes. Currently supported is the i.MX6dl version with
256MB DDR3 RAM.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

images: move board variable to parent makefile ...

A lot of the image makefiles define an equal board variable, which
gives the impression that this variable is unique for this makefile.
As those files aren't freestanding makefiles but get included into a
parent makefile this is not actually true. Attempts to override this
variable will not work reliable as make is picking up a random instance.

Fix this confusion by moving this variable out of the individual makefiles.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: phyFLEX-i.MX6: Add support for 1GB on 1 bank ...

Add support phyFLEX-i.MX6 SOM with 1GB on one ram bank

Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX: Add i.MX6sx sabresdb support ...

This adds support for the Freescale i.MX6sx sabresdb board.

Tested are:

- UART
- The three SD card slots
- USB host
- USB otg (host and device mode)
- FEC (both)

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

imx6: Add support for phyBOARD-SUBRA ...

Add support for phyBOARD-SUBRA which use a phyFLEX-i.MX6 (pfla02) module.
	- i.MX6 SOLO with 512MB RAM

Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

imx6: add support for phyBOARD-ALCOR ...

Add support for phyBOARD-ALCOR which use a phyFLEX-i.MX6 (pfla02) module.
        - i.MX6 Quad with 1GB RAM on two banks

Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: nitrogen6x: Add support for 2GB board variants ...

The nitrogen6x have variants with 2GB SDRAM. Add support for them. The
imxcfg files are from U-Boot.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX6: add support for Karo TX6X family ...

The Karo TX6X family consists of different i.MX6Q/DL based System-on-Modules.
Add support for the TX6u 801x modules, that have an i.MX6DL SoC.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

arm: imx6: add Gateworks Ventana board ...

For now only the Quad 1GB variant is supported.

Tested:
- starting barebox over USB
- writing barebox to NAND with barebox_update
- starting Linux kernel over TFTP

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

arm: nitrogen6x: new memory setup from BD u-boot ...

This fixes various stability issues seen on new boards
with the old setup.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/imx'