driver: replace dev_request_mem_region with dev_request_mem_resource ...

dev_request_mem_region doesn't work properly one some SoCs on which
PTR_ERR() values clash with valid return values from dev_request_mem_region.
Replace them with dev_request_mem_resource where possible.

This patch has been generated with the following semantic patch:

// <smpl>
@@
expression d;
expression n;
expression io;
identifier func;
@@
func(...) {
+struct resource *iores;
<+...
-io = dev_request_mem_region(d, n);
-if (IS_ERR(io)) {
+iores = dev_request_mem_resource(d, n);
+if (IS_ERR(iores)) {
...
-	return PTR_ERR(io);
-}
+	return PTR_ERR(iores);
+}
+io = IOMEM(iores->start);
...+>
}

@@
expression d;
expression n;
expression io;
identifier func;
@@
func(...) {
+struct resource *iores;
<+...
-io = dev_request_mem_region(d, n);
-if (IS_ERR(io)) {
+iores = dev_request_mem_resource(d, n);
+if (IS_ERR(iores))
-	return PTR_ERR(io);
-}
+	return PTR_ERR(iores);
+io = IOMEM(iores->start);
...+>
}

@@
expression d;
expression n;
expression io;
identifier func;
@@
func(...) {
+struct resource *iores;
<+...
-io = dev_request_mem_region(d, n);
-if (IS_ERR(io)) {
-	ret = PTR_ERR(io);
+iores = dev_request_mem_resource(d, n);
+if (IS_ERR(iores)) {
+	ret = PTR_ERR(iores);
...
}
+io = IOMEM(iores->start);
...+>
}

@@
expression d;
expression n;
expression io;
identifier func;
@@
func(...) {
+struct resource *iores;
<+...
-io = dev_request_mem_region(d, n);
+iores = dev_request_mem_resource(d, n);
+if (IS_ERR(iores))
+	return PTR_ERR(iores);
+io = IOMEM(iores->start);
...+>
}

@@
identifier func;
@@
func(...) {
<+...
struct resource *iores;
-struct resource *iores;
...+>
}
// </smpl>

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

resource: Let dev_request_mem_region return an error pointer ...

For all users fix or add the error check.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

spi: altera_spi: fix altera_spi_setup() return error codes ...

Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

spi: altera_spi: Remove redundant assignment ...

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Use new device_platform_driver() macro for drivers ...

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

switch all platform_bus device/driver registering to platform_driver/device_register ...

now register_driver and register_device are for bus only usage.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Treewide: remove address of the Free Software Foundation ...

The FSF address has changed in the past. Instead of updating it
each time the address changes, just drop it completely treewide.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

spi/altera_spi: Add cs_change support ...

The Linux kernel says (spi.h) :

* All SPI transfers start with the relevant chipselect active.  Normally
* it stays selected until after the last transfer in a message.  Drivers
* can affect the chipselect signal using cs_change.
*
* (i) If the transfer isn't the last one in the message, this flag is
* used to make the chipselect briefly go inactive in the middle of the
* message.  Toggling chipselect in this way may be needed to terminate
* a chip command, letting a single spi_message perform all of group of
* chip transactions together.
*
* (ii) When the transfer is the last one in the message, the chip may
* stay selected until the next transfer.  On multi-device SPI busses
* with nothing blocking messages going to other devices, this is just
* a performance hint; starting a message to another device deselects
* this one.  But in other cases, this can be used to ensure correctness.
* Some devices need protocol transactions to be built from a series of
* spi_message submissions, where the content of one message is
* determined by the results of previous messages and where the whole
* transaction
* ends when the chipselect goes intactive.

In other words, cs_change changes the default chipselect *behavior*.

Support of cs_change is necessary to implement the mci spi driver.

This patch also fix few things:

Passing the bus number to the brand new master device.
Disable chipselect during master->setup.

Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

introduce io.h ...

To allow for some generic io accessors introduce io.h and use
this instead of asm/io.h throughout the tree.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

nios2: Add Altera SPI master driver ...

Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>