console: replace set_active by open/close ...

Opening and closing consoles should be independent from setting them
active. This way it is possible to open e.g. a framebuffer console and
display text on it without showing stdout/stderr.

Signed-off-by: Bastian Stender <bst@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: add linux.bootarg parameter from ifup call ...

This sets a `ip=dhcp` or
`ip=<clientip>:<serverip>:<gatewayip>:<netmaskip>::<iface>:` bootarg for
the network device upon execution of 'ifup'. This is the only point
where we can distinguish between a static ip and a dhcp-based network
setup and thus set a valid bootarg options as it will be required for
nfs boot, for example.

Signed-off-by: Enrico Jorns <ejo@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

convert users to %pI4 ...

Convert users of ip_to_string() and print_IPaddr() to %pI4 and
remove the now unused functions.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: Pass network device to net_answer_arp() ...

The caller already has the correct network device, so pass it
to net_answer_arp() rather than using eth_get_current() there.
This is a step towards making a global current network device
unnecessary.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: eth: add name to struct eth_device ...

Using dev_name often is not a good idea since it's a statically
allocated string which gets overwritten by later calls to dev_name.
Add a devname string to struct eth_device to have the name available
for later use.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: introduce for_each_netdev iterator ...

for_each_netdev is nicer to read. Also export the list of network
devices since it will be used by code outside of net/eth.c in later
patches.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: eth: open correct edev in eth_check_open ...

eth_check_open gets the network device to check as parameter, so
use it rather than using eth_current. Currently both are the same,
so this currently does not fix anything.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ifup: fix handling when ip env is not given ...

This patch handles the ip env to "" if no ip env is given. Otherwise
we get a NULL pointer derefence.

Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

string: Fix (v)asprintf prototypes ...

Our asprintf and vasprintf have different prototypes than the glibc
functions. This causes trouble when we want to share barebox code
with userspace code. Change the prototypes for (v)asprintf to match
the glibc prototypes. Since the current (v)asprintf are convenient
to use change the existing functions to b(v)asprintf.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/rtc'

net: Add SNTP support ...

This adds support for retrieving the time via Simple Network Time
Protocol (SNTP). No fancy features are supported, only plainly getting
the current time.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: resolv: Make argument const ...

resolv() is not allowed to change the hostname argument, make it const.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: dhcp: make unmodified variable const ...

'str' in dhcp_set_string_options is never modified, so make it const.
With this we no longer have to cast away the const returned from getenv.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: dhcp: simplify dhcp_options_process ...

dhcp_options_handle returns the index into the dhcp_options array.
This is only to be able in the caller to print a debug message when
the index returned from dhcp_options_handle is out of bounds.
Simplify this by printing the debug message in dhcp_options_handle
and not in the caller.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: dhcp: unify options and params ...

The dhcp code distinguishes between options and params. If sent to the
server they are params, if received from the server they are options.
Unify them all to be options. If it has a handle_param callback it's
a param, if it has a handle callback it's an option.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: eth: Remove ethaddr_param ...

commit d00db554 introduce ethaddr_param. But it is not initialized, so
devinfo fails to show the mac. Remove it and use edev->ethaddr.

Signed-off-by: Jan Remmet <j.remmet@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: eth: Fixup OF tree with registered MAC addresses too ...

The eth code registers an OF tree fixup that looks for any nodes in
the Linux oftree that match eth devices loaded in barebox and sets the
mac-address property in those nodes.  The purpose is to pass MAC
addresses to the Linux kernel for drivers that expect the MAC address
to be in the device tree.

If barebox does not have a driver for the network device, either
because it has been disabled or because one does not exist, then the
OF tree will not be fixed up to include a MAC address.

The eth code also has a list of MAC addresses which board code has
registered, usually done when it reads the address from an EEPROM or
on-chip memory.  If an eth device is created later in the boot, it
will look here for an address.

The registered MAC address list is not used for the OF tree fix up,
and this patch changes that.  This way barebox can place a MAC address
in the device-tree without needing a driver for the network device.

Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: eth: Refactor OF tree fixup of one node into new function ...

Code that fixes up one node with a new MAC address is refactored into
a new function that eth_of_fixup() calls in a loop.

Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: dhcp: Fix CONFIG variable name ...

Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/net'

net: make eth_register_ethaddr work on registered network devices ...

When eth_register_ethaddr is called after the device has been registered
it should work aswell.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: eth_send: Allow to use multiple network interfaces at once ...

The commit

commit be0404c
Author: Sascha Hauer <s.hauer@pengutronix.de>
Date:   Wed May 14 16:08:04 2014 +0200

    net: Allow to use multiple network interfaces at once

changes the eth_send() function:

-       return eth_current->send(eth_current, packet, length);
+       return edev->send(eth_current, packet, length);

But we have to change the both eth_current occurrences to edev here!

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/net'

treewide: fix 'new blank line at EOF' formatting error ...

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: Move library functions to net/lib.c ...

Some network related functions are also needed when networking
is disabled. Move these to a separate file which is always compiled.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

dns: handle incoming packets in the separate dns_recv() function ...

The separation of incoming packets handling makes it much easier
to run barebox dns client on top of picotcp network stack in the future.

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: eth: Do not rely on CONFIG_PARAMETER to be enabled ...

register_preset_mac_address only works when CONFIG_PARAMETER
is enabled because otherwise dev_set_param is a no-op. Add a
function to set the MAC address explicitly without the need
of CONFIG_PARAMETER and use it where appropriate.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/am33xx'

net: dhcp: Split dhcp funcionality & add dhcp command ...

dhcp/bootp was bound to the command functionality.
This patch splits the dhcp command.
We are now able to use bootp without a shell.

This patch adds also a check for environment variables and globalvar.
So only when ENVIRONMENT_VARIABLES and GLOBALVAR is set, all received
dhcp data will be stored.

Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

eth: halt active ethernet device on unregister ...

When an active ethernet device is unregistered it should
be halted to quiesce the device.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>