ARM: Add i.MX6ull evk support ...

The i.MX6ull-EVK is a evaluation board for the i.MX6ull from NXP.
The upstream DTS is used, support should be fairly complete:

- 2x fec ethernet
- 1x USB Host
- 1x USB OTG
- 2x SD

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX: Add support for NXP i.MX7 SABRESD board ...

Add minimal code to support NXP i.MX7 SABRESD board. Tested to have
working SD card and first Ethernet port as well as being able to boot
upstream Linux kernel (4.12+).

Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>

ARM: imx: phyCORE i.MX7 on phyBOARD-Zeta support ...

This adds preliminary support for the phyCORE i.MX7 module on a
phyBOARD-Zeta baseboard. The DTs will likely change in the future
when PHYTEC finalizes their BSP.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>

ARM: i.MX6: add Technexion Pico Hobbit support ...

This adds support for the i.MX6UL Technexion Pico Hobbit. The board
comes with different amounts of RAM. We create one image for the 256MB
and one for the 512MB variant.

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
   ---
   v1 -> v2: - removed already prepared clock setup
   v2 -> v3: - added phy-reset-post-delay as the support is now available

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARCH: ARM: Add support for phytec-phycore-imx6ull ...

Created imx6ull devicetree to support Phytec phyCORE-i.MX6ULL.
 - 256 MB RAM
 - 128 MB NAND
 - 10/100 Mbit Ethernet

Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX50: Add support for i.MX50 based Amazon Kindle e-book readers ...

The Kindle Model No. D01100 (Kindle Wi-Fi), D01200 (Kindle Touch)
and EY21 (Kindle Paperwhite) are refered as the Kindle 4th and 5th generation.
Those models are based on an i.MX50 SoC and use LPDDR1 or LPDDR2 Memory.

The devices boot in internal boot mode from a build-in eMMC, alternatively
some devices may be set into USB-downloader mode by pressing a specific key
at startup.

Add support for the i.MX50 based Kindle device and make barebox a drop-in
replacement for the factory shipped u-boot image.

Notable features:
- Support for eMMC, USB, UART, I2C, SPI and Keys (except keyboard).
- LPDDR1 and LPDDR2 setup is done via DCD, the same imximage may be used
  for USB-startup and for installation.
- Support for vendor specific ATAGs that are required for the Kindle-System.
- usbserial barebox console access by pressing Select button at startup,
  alternatively full console support on connector J14.

Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: imx6: add Hummingboard2 support ...

This adds support for the Hummingboard2 baseboard for the SolidRun
MicroSOM modules.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX: vf610: Add support for ZII VF610 Dev Family ...

Add support for ZII VF610 Dev based designs such as:

    - VF610 Dev, revision B
    - VF610 Dev, revision C
    - CFU1, revision A
    - SPU3, revision A
    - SCU4 AIB, revision C

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX: Add WaRP7 board support ...

Signed-off-by Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: rdu2: support QP variant ...

This adds support for the QuadPlus variant of the board as a separate
Barebox binary.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: imx: Add support for ZII RDU2 board ...

Add support for RDU2 board from Zodiac Inflight Innovations.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARCH: ARM: Add support for phytec-phycore-imx6ul ...

Add support for the phycore i.MX6 UltraLite.
 - 512MB RAM
 - 512MB NAND
 - 10/100 Mbit Ethernet

Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Lengfeld <s.lengfeld@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX: Add support for VF610 Tower board ...

Add support for VF610 Tower board.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: imx6: add support for Auvidea H100 ...

The Auvidea H100 is a baseboard for the SolidRun MicroSOM, which
provides HDMI IN/OUT capabilities.

Currently supported is only a combination of the H100 baseboard
with a i2eX MicroSOM.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX53 Vincell: Add NAND xload support ...

The Vincell boards do the SDRAM setup from board init code, so the
image size is limited to the internal SRAM size. To overcome this
limitation use the NAND xload support.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: nitrogen: rename to nitrogen6 ...

Now that the MAX variant of the board is also supported by the
same code, rename the board directory to the more generic nitrogen6.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: add support for Nitrogen6MAX QP variant ...

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX: karo-tx6: Add support for the 512MiB i.MX6s variant ...

This adds support for the TX6S-8x35 board variant.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/imx6-phytec'

ARM: phytec-som-imx6: add phyCORE-i.MX6 DualLite ...

Add Phytec phyCORE-i.MX6 SOM.
  Support:
   - imx6dl-phytec-phycore-som-emmc:
      - 1GB RAM on 1 Bank with 64Bit
      - 10/100MBit Ethernet
      - SPI NOR
      - eMMC
      - SD
      - UART

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: phytec-som-imx6: add phyCORE-i.MX6 Quad 2GiB RAM ...

Add new Phytec phyCORE-i.MX6 SOM:
  Support:
    - imx6q-phytec-phycore-som-emmc:
       - 2GiB RAM on 1 Bank with 64Bit
       - 1GBit Ethernet
       - SPI NOR
       - eMMC
       - SD
       - UART

Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: imx6q: add support for phyBOARD-SUBRA-i.MX6 Quad ...

Add support for phyBOARD-SUBRA-i.MX6 with phyFLEX-i.MX6 Quad 1GiB on one
bank. This patch factors out the common device tree nodes for the Quad
and Solo variant into 'imx6qdl-phytec-phyboard-subra.dtsi'.

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX: karo-tx6: Add support for the 2GiB i.MX6q+ board variant ...

Different SDRAM setup, but same board otherwise.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: i.MX: karo-tx6: Add support for the i.MX6q 1GiB variant ...

The i.MX6q variant is basically the same as the i.MX6dl variant, just
with another SoC and the usual i.MX6q/i.MX6dl adjustments.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

images: imx: Add targets for signed images and signed usb images ...

Add .simximg target for signed images and .usimximg for signed
images suitable for USB upload

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Make: i.MX: Allow to pass config file to cmd_imx_image ...

Pass the config file to cmd_imx_image as arguments to make it more
flexible. Also add the possibility for another arg containing additional
options.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: mx6sx-sabresdb: set proper hostname ...

Also move the initcall to the level matching the name of the
function.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: imx6dl: Add support for Phytec phyCORE-i.MX6 SOM ...

Add Phytec phyCORE-i.MX6 SOM.
     - imx6dl-phytec-phycore-som-nand
        - 256GB RAM on 1 Bank with 32Bit
        - 10/100MBit Ethernet
        - NAND
        - SD
        - UART

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: imx6q: Add support for Phytec phyCORE-i.MX6 SOM ...

Add Phytec phyCORE-i.MX6 SOM.
    Support:
     - imx6q-phytec-phycore-som-nand:
        - 1GB RAM on 1 Bank with 64Bit
        - 1GBit Ethernet
        - SPI NOR
        - NAND
        - SD
        - UART

     - imx6q-phytec-phycore-som-emmc
        - 1GB RAM on 1 Bank with 64Bit
        - 1GBit Ethernet
        - SPI NOR
        - eMMC
        - SD
        - UART

Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

ARM: imx6q: pfla02: add phyFLEX-i.MX6 DualLite 1GiB on one bank ...

Add support for phyFLEX-i.MX6 DualLite 1GiB on one bank with NOR.

Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>