Merge branch 'for-next/socfpga'

Merge branch 'for-next/pci'

Merge branch 'for-next/misc'

Merge branch 'for-next/imx'

serial: lpuart: Avoid division by zero when requested baudrate is ...

With serdev device support added there's now a corner case where:

 1. There is a DT node for a serdev device on one of the UARTs
 2. There is no driver that binds against serdev device's compatibility
    string

with 1 and 2 being true it is possible to end up in a situation where
a particualr UART has not been initalized to any baudrate when
clock_notifier_call_chain() gets called. This effectively translates
to

	set_baudrate(uart, 0);

which for LPUART driver result in a division by zero.

To avoid this problem, convert lpuart_serial_setbaudrate() to treat
zero baudrate as a request to disable the UART. While we are at it add
a BUG_ON() to lpuart_setbrg() to simplify finding any future bugs.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

pinctrl: i.MX: Add code to parse "input-enable" ...

Add code to parse "input-enable" and intepret it as SION bit. This is
needed for I2C configuration on i.MX8MQ EVK board.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX: Select DRIVER_SPI_IMX_2_3 for i.MX8MQ ...

Select DRIVER_SPI_IMX_2_3 for i.MX8MQ since that is the variant that's
being used

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX: i2c: Fix build error in debug output code ...

Looks like that particular chunk of the code have not been built in a
while and bitrotted. Change function parameters appropriately to avoid
breaking the build.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: imx-esdhc: send required clock pulses to card on init ...

MMC cards need at least 74 clock pulses before any bus communication
can occur. The i.MX SDHC controller auto-gates the clock when inactive,
so if the SD enumeration is skipped for slots where we know that only a
MMC card can be present (which is possible since
b5289b742a89 "mmc: allow skipping SD card initialization") those
inititialization clock pulses won't be sent out, resulting in command
timeouts when trying to enumerate the card.

Luckily the eSDHC controller has a hardware feature to send out 80
clock pulses. This has been validated to be available by checking the
reference manual back to i.MX25.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

usb: gadget: allow to actually enable sparse fastboot support ...

When sparse support was (intended to be) made optional it was
effectively unconditionally disabled because

	IS_ENABLED(USB_GADGET_FASTBOOT_SPARSE)

always evaluates to 0. To actually make use of the introduced kconfig
symbol the CONFIG_ prefix must not be skipped.

Fixes: f4b5d3eeb607 ("usb: gadget: fastboot: Make sparse support optional")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Gavin Schenk <g.schenk@eckelmann.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: s3c: fix providing info callback ...

There is no symbol iCONFIG_MCI_INFO, CONFIG_MCI_INFO makes sense here
and matches what was added in the same commit to other drivers.

Fixes: 73b0d228e5b0 ("driver: Attach info callback to device, not to driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

pci: add quirk infrastructure ...

This is a cut down version of the Linux kernel PCI quirk infrastructure,
which allows to register and execute some fixups before the driver is
loaded.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

PCI: link PCI devices with potentially existing OF nodes ...

The document "PCI Bus Binding to: IEEE Std 1275-1994 Standard for Boot
(Initialization Configuration) Firmware" describes how the PCI topology
can be described in the DT, in order to augment the PCI devices with
additional information via DT properties.

This patch links OF nodes to the corresponding PCI devices if they
exist, allowing PCI device drivers to query DT information like any
platform device.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: dw: move defines to headerfile ...

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: dw_mmc: convert to BIT() macro ...

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mci: dw_mmc: remove device_d pointer ...

The pointer to the struct device_d *dev is also saved to the struct mci_host.
Get rid of it.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

reset: socfpga: add missing driver name ...

The driver_d is missing the name property. When the reset driver is used in a
non-of setup, this will result in an error during device_registration where
the dev->name is matched to the driver->name.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

imx_thermal: Fixed missing dependency for the IMX_THERMAL config ...

The temperature sensor driver for Freescale i.MX SoCs use internaly the OCOTP character device. If the config IMX_THERMAL is selected the OCOTP config was not selected and comes up with an error during booting.

Signed-off-by: Eugen Wiens <eugen.wiens@jumo.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

aiodev: Fix whitespaces in Kconfig ...

Replace whitespaces with tabs.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net/e1000: allow to overwrite flash size from device tree ...

When barebox probes the e1000 driver and the flash on the i210 device is
unprogrammed, the driver assumes the flash has a size of only 4 kiB.
This is annoying because to program the flash an image must be written
that is bigger than 4 kiB. So you first have to flash the first sector
to make barebox detect the right size on the next boot. Then reset the
board to be able to write the remaining data.

To work around that limitation, try to read the actual size from the
device tree. (Note however that barebox' pci code currently doesn't use
the device tree and so currently this try always fails without further
patching.)

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Merge branch 'for-next/misc'

Merge branch 'for-next/imx8mq'

Merge branch 'for-next/imx'

mtd: gpmi-nand: Make sure clock is disabled during rate change ...

On i.MX6 GPMI Nand controller the clock must be disabled during
a rate change. Otherwise glitches on the clock line may occur
which result in errors like:

MXS NAND: Error sending command
MXS NAND: DMA read error

There were previous attempts to fix this. One is in:

54961378f0 imx6: clk: Gate off ENFC clock before setting clock rate

This patch added a clk_disable() right before the rate change. Since
a clk_disable() on a disabled clk is a no-op, the patch added a
clk_enable() to the i.MX6 clk driver in the hope that the clk is
enabled in the nand driver probe and the clk_disable() really takes
place.

This patch doesn't work. First of all it enabled the enfc_podf clk
which was not the one that was actually disabled in the nand driver,
resulting in the nand drivers call to clk_disable() still being a
no-op. Then this patch also only works only on the classic i.MX6 which
was the only one supported at that time, but not on the i.MX6UL, i.MX6SX
and i.MX6SL which have a separate clk driver.

Instead of adding more quirks to the other i.MX6 clk drivers, fix this
in the GPMI driver. We no longer call clk_disable() on a disabled clk,
but instead do a clk_enable() first which makes sure the hardware state
is synchronized to the usage count and the following clk_disable()
is really effective. At the same time we can (and actually must) remove
the quirk in the i.MX6 clk driver.

Also add clk_disable()/clk_enable() around another rate change in the
GPMI driver.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

clk: imx: remove unused clk_gate2_inverted ...

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

nvmem: rave-sp-eeprom: Add support for "zii,eeprom-name" ...

Upstream kernel driver allows specifying EEPROM name via
"zii,eeprom-name" property. Add code to support that in Barebox as
well.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

nvmem: rave-sp-eeprom: Remove VLA usage ...

This is a backport of patch [1] by Kees Cook

[1] https://lkml.kernel.org/r/20180620182600.GA24297@beast

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

mtd: mtd_dataflash: Don't print bogus command values for READs ...

Call to dev_dbg in dataflash_read() is located to early, before
command[] is initialize to correct values, so it end up printing
values from previous invocation. Move it such that it prints current
call's values.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

net: designware: make sure DMA is disabled on kernel start. ...

Halt is not automatically executed if we start the kernel.
So, we may have potentially memory corruptions.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

nvmem: Introduce nvmem_cell_get_and_read() ...

Introduce nvmem_cell_get_and_read() that combines getting a NVMEM cell
by name and reading its contents.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>