/**************************************************************************//**
 * @file     sc.h
 * @version  V1.00
 * $Revision: 10 $
 * $Date: 14/09/29 2:01p $
 * @brief    NUC472/NUC442 Smartcard (SC) driver header file
 *
 * @note
 * Copyright (C) 2014 Nuvoton Technology Corp. All rights reserved.
 *****************************************************************************/
#ifndef __SC_H__
#define __SC_H__

#ifdef __cplusplus
extern "C"
{
#endif


/** @addtogroup NUC472_442_Device_Driver NUC472/NUC442 Device Driver
  @{
*/

/** @addtogroup NUC472_442_SC_Driver SC Driver
  @{
*/

/** @addtogroup NUC472_442_SC_EXPORTED_CONSTANTS SC Exported Constants
  @{
*/
#define SC_INTERFACE_NUM        6                /*!< Smartcard interface numbers \hideinitializer */
#define SC_PIN_STATE_HIGH       1                /*!< Smartcard pin status high   \hideinitializer */
#define SC_PIN_STATE_LOW        0                /*!< Smartcard pin status low    \hideinitializer */
#define SC_PIN_STATE_IGNORE     0xFFFFFFFF       /*!< Ignore pin status           \hideinitializer */
#define SC_CLK_ON               1                /*!< Smartcard clock on          \hideinitializer */
#define SC_CLK_OFF              0                /*!< Smartcard clock off         \hideinitializer */

#define SC_TMR_MODE_0                   (0ul << SC_TMRCTL0_OPMODE_Pos)     /*!<Timer Operation Mode 0, down count                                                      \hideinitializer */
#define SC_TMR_MODE_1                   (1ul << SC_TMRCTL0_OPMODE_Pos)     /*!<Timer Operation Mode 1, down count, start after detect start bit                        \hideinitializer */
#define SC_TMR_MODE_2                   (2ul << SC_TMRCTL0_OPMODE_Pos)     /*!<Timer Operation Mode 2, down count, start after receive start bit                       \hideinitializer */
#define SC_TMR_MODE_3                   (3ul << SC_TMRCTL0_OPMODE_Pos)     /*!<Timer Operation Mode 3, down count, use for activation, only timer 0 support this mode  \hideinitializer */
#define SC_TMR_MODE_4                   (4ul << SC_TMRCTL0_OPMODE_Pos)     /*!<Timer Operation Mode 4, down count with reload after timeout                            \hideinitializer */
#define SC_TMR_MODE_5                   (5ul << SC_TMRCTL0_OPMODE_Pos)     /*!<Timer Operation Mode 5, down count, start after detect start bit, reload after timeout  \hideinitializer */
#define SC_TMR_MODE_6                   (6ul << SC_TMRCTL0_OPMODE_Pos)     /*!<Timer Operation Mode 6, down count, start after receive start bit, reload after timeout \hideinitializer */
#define SC_TMR_MODE_7                   (7ul << SC_TMRCTL0_OPMODE_Pos)     /*!<Timer Operation Mode 7, down count, start and reload after detect start bit             \hideinitializer */
#define SC_TMR_MODE_8                   (8ul << SC_TMRCTL0_OPMODE_Pos)     /*!<Timer Operation Mode 8, up count                                                        \hideinitializer */
#define SC_TMR_MODE_F                   (0xF << SC_TMRCTL0_OPMODE_Pos)     /*!<Timer Operation Mode 15, down count, reload after detect start bit                      \hideinitializer */


/*@}*/ /* end of group NUC472_442_SC_EXPORTED_CONSTANTS */


/** @addtogroup NUC472_442_SC_EXPORTED_FUNCTIONS SC Exported Functions
  @{
*/

/**
  * @brief This macro enable smartcard interrupt
  * @param[in] sc Base address of smartcard module
  * @param[in] u32Mask Interrupt mask to be enabled. A combination of
  *             - \ref SC_INTEN_ACERRIEN_Msk
  *             - \ref SC_INTEN_RXTOIF_Msk
  *             - \ref SC_INTEN_INITIEN_Msk
  *             - \ref SC_INTEN_CDIEN_Msk
  *             - \ref SC_INTEN_BGTIEN_Msk
  *             - \ref SC_INTEN_TMR2IEN_Msk
  *             - \ref SC_INTEN_TMR1IEN_Msk
  *             - \ref SC_INTEN_TMR0IEN_Msk
  *             - \ref SC_INTEN_TERRIEN_Msk
  *             - \ref SC_INTEN_TBEIEN_Msk
  *             - \ref SC_INTEN_RDAIEN_Msk
  * @return None
  * \hideinitializer
  */
#define SC_ENABLE_INT(sc, u32Mask) ((sc)->INTEN |= (u32Mask))

/**
  * @brief This macro disable smartcard interrupt
  * @param[in] sc Base address of smartcard module
  * @param[in] u32Mask Interrupt mask to be disabled. A combination of
  *             - \ref SC_INTEN_ACERRIEN_Msk
  *             - \ref SC_INTEN_RXTOIF_Msk
  *             - \ref SC_INTEN_INITIEN_Msk
  *             - \ref SC_INTEN_CDIEN_Msk
  *             - \ref SC_INTEN_BGTIEN_Msk
  *             - \ref SC_INTEN_TMR2IEN_Msk
  *             - \ref SC_INTEN_TMR1IEN_Msk
  *             - \ref SC_INTEN_TMR0IEN_Msk
  *             - \ref SC_INTEN_TERRIEN_Msk
  *             - \ref SC_INTEN_TBEIEN_Msk
  *             - \ref SC_INTEN_RDAIEN_Msk
  * @return None
  * \hideinitializer
  */
#define SC_DISABLE_INT(sc, u32Mask) ((sc)->INTEN &= ~(u32Mask))

/**
  * @brief This macro set VCC pin state of smartcard interface
  * @param[in] sc Base address of smartcard module
  * @param[in] u32State Pin state of VCC pin, valid parameters are \ref SC_PIN_STATE_HIGH and \ref SC_PIN_STATE_LOW
  * @return None
  * \hideinitializer
  */
#define SC_SET_VCC_PIN(sc, u32State) \
    do {\
            while(sc->PINCTL & SC_PINCTL_SYNC_Msk);\
            if(u32State)\
                (sc)->PINCTL |= SC_PINCTL_PWREN_Msk;\
            else\
                (sc)->PINCTL &= ~SC_PINCTL_PWREN_Msk;\
    }while(0)


/**
  * @brief This macro turns CLK output on or off
  * @param[in] sc Base address of smartcard module
  * @param[in] u32OnOff Clock on or off for selected smartcard module, valid values are \ref SC_CLK_ON and \ref SC_CLK_OFF
  * @return None
  * \hideinitializer
  */
#define SC_SET_CLK_PIN(sc, u32OnOff)\
    do {\
            while(sc->PINCTL & SC_PINCTL_SYNC_Msk);\
            if(u32OnOff)\
                (sc)->PINCTL |= SC_PINCTL_CLKKEEP_Msk;\
            else\
                (sc)->PINCTL &= ~(SC_PINCTL_CLKKEEP_Msk);\
    }while(0)

/**
  * @brief This macro set I/O pin state of smartcard interface
  * @param[in] sc Base address of smartcard module
  * @param[in] u32State Pin state of I/O pin, valid parameters are \ref SC_PIN_STATE_HIGH and \ref SC_PIN_STATE_LOW
  * @return None
  * \hideinitializer
  */
#define SC_SET_IO_PIN(sc, u32State)\
    do {\
            while(sc->PINCTL & SC_PINCTL_SYNC_Msk);\
            if(u32State)\
                (sc)->PINCTL |= SC_PINCTL_SCDOUT_Msk;\
            else\
                (sc)->PINCTL &= ~SC_PINCTL_SCDOUT_Msk;\
    }while(0)

/**
  * @brief This macro set RST pin state of smartcard interface
  * @param[in] sc Base address of smartcard module
  * @param[in] u32State Pin state of RST pin, valid parameters are \ref SC_PIN_STATE_HIGH and \ref SC_PIN_STATE_LOW
  * @return None
  * \hideinitializer
  */
#define SC_SET_RST_PIN(sc, u32State)\
    do {\
            while(sc->PINCTL & SC_PINCTL_SYNC_Msk);\
            if(u32State)\
                (sc)->PINCTL |= SC_PINCTL_SCRST_Msk;\
            else\
                (sc)->PINCTL &= ~SC_PINCTL_SCRST_Msk;\
    }while(0)

/**
  * @brief This macro read one byte from smartcard module receive FIFO
  * @param[in] sc Base address of smartcard module
  * @return One byte read from receive FIFO
  * \hideinitializer
  */
#define SC_READ(sc) ((char)((sc)->DAT))

/**
  * @brief This macro write one byte to smartcard module transmit FIFO
  * @param[in] sc Base address of smartcard module
  * @param[in] u8Data Data to write to transmit FIFO
  * @return None
  * \hideinitializer
  */
#define SC_WRITE(sc, u8Data) ((sc)->DAT = (u8Data))

/**
  * @brief This macro set smartcard stop bit length
  * @param[in] sc Base address of smartcard module
  * @param[in] u32Len Stop bit length, ether 1 or 2.
  * @return None
  * @details Stop bit length must be 1 for T = 1 protocol and 2 for T = 0 protocol.
  * \hideinitializer
  */
#define SC_SET_STOP_BIT_LEN(sc, u32Len) ((sc)->CTL = ((sc)->CTL & ~SC_CTL_NSB_Msk) | (u32Len == 1 ? 1 : 0))

/**
  * @brief  Enable/Disable Tx error retry, and set Tx error retry count
  * @param[in]  sc Base address of smartcard module
  * @param[in]  u32Count The number of times of Tx error retry count, between 0~8. 0 means disable Tx error retry
  * @return None
  */
__STATIC_INLINE void SC_SetTxRetry(SC_T *sc, uint32_t u32Count)
{
    while(sc->CTL & SC_CTL_SYNC_Msk);
    if(u32Count == 0) {       // disable Tx error retry
        sc->CTL &= ~(SC_CTL_TXRTY_Msk | SC_CTL_TXRTYEN_Msk);
    } else {
        sc->CTL = (sc->CTL & ~SC_CTL_TXRTY_Msk) | ((u32Count - 1) << SC_CTL_TXRTY_Pos) | SC_CTL_TXRTYEN_Msk;
    }
}

/**
  * @brief  Enable/Disable Rx error retry, and set Rx error retry count
  * @param[in]  sc Base address of smartcard module
  * @param[in]  u32Count The number of times of Rx error retry count, between 0~8. 0 means disable Rx error retry
  * @return None
  */
__STATIC_INLINE void  SC_SetRxRetry(SC_T *sc, uint32_t u32Count)
{
    while(sc->CTL & SC_CTL_SYNC_Msk);
    if(u32Count == 0) {       // disable Rx error retry
        sc->CTL &= ~(SC_CTL_RXRTY_Msk | SC_CTL_RXRTYEN_Msk);
    } else {
        sc->CTL = (sc->CTL & ~SC_CTL_RXRTY_Msk) | ((u32Count - 1) << SC_CTL_RXRTY_Pos) | SC_CTL_RXRTYEN_Msk;
    }
}


uint32_t SC_IsCardInserted(SC_T *sc);
void SC_ClearFIFO(SC_T *sc);
void SC_Close(SC_T *sc);
void SC_Open(SC_T *sc, uint32_t u32CardDet, uint32_t u32PWR);
void SC_ResetReader(SC_T *sc);
void SC_SetBlockGuardTime(SC_T *sc, uint32_t u32BGT);
void SC_SetCharGuardTime(SC_T *sc, uint32_t u32CGT);
void SC_StopAllTimer(SC_T *sc);
void SC_StartTimer(SC_T *sc, uint32_t u32TimerNum, uint32_t u32Mode, uint32_t u32ETUCount);
void SC_StopTimer(SC_T *sc, uint32_t u32TimerNum);


/*@}*/ /* end of group NUC472_442_SC_EXPORTED_FUNCTIONS */

/*@}*/ /* end of group NUC472_442_SC_Driver */

/*@}*/ /* end of group NUC472_442_Device_Driver */

#ifdef __cplusplus
}
#endif

#endif //__SC_H__

/*** (C) COPYRIGHT 2014 Nuvoton Technology Corp. ***/