/* mbed Microcontroller Library
* SPDX-License-Identifier: BSD-3-Clause
******************************************************************************
*
* Copyright (c) 2015-2021 STMicroelectronics.
* All rights reserved.
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/**
* This file configures the system clock as follows:
*-----------------------------------------------------------------------------
* System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI
* | (external 8 MHz clock) | (internal 16 MHz)
* | 2- PLL_HSE_XTAL |
* | (external 8 MHz xtal) |
*-----------------------------------------------------------------------------
* SYSCLK(MHz) | 168 | 168
*-----------------------------------------------------------------------------
* AHBCLK (MHz) | 168 | 168
*-----------------------------------------------------------------------------
* APB1CLK (MHz) | 42 | 42
*-----------------------------------------------------------------------------
* APB2CLK (MHz) | 84 | 84
*-----------------------------------------------------------------------------
* USB capable (48 MHz precise clock) | YES | NO
*-----------------------------------------------------------------------------
**/
#include "stm32f4xx.h"
#include "mbed_error.h"
/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */
#define USE_PLL_HSE_EXTC (1) /* Use external clock */
#define USE_PLL_HSE_XTAL (1) /* Use external xtal */
#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
#endif
uint8_t SetSysClock_PLL_HSI(void);
/**
* @brief Configures the System clock source, PLL Multiplier and Divider factors,
* AHB/APBx prescalers and Flash settings
* @note This function should be called only once the RCC clock configuration
* is reset to the default reset state (done in SystemInit() function).
* @param None
* @retval None
*/
MBED_WEAK void SetSysClock(void)
{
/* 1- Try to start with HSE and external clock */
#if USE_PLL_HSE_EXTC != 0
if (SetSysClock_PLL_HSE(1) == 0)
#endif
{
/* 2- If fail try to start with HSE and external xtal */
#if USE_PLL_HSE_XTAL != 0
if (SetSysClock_PLL_HSE(0) == 0)
#endif
{
/* 3- If fail start with HSI clock */
if (SetSysClock_PLL_HSI() == 0) {
while (1) {
// [TODO] Put something here to tell the user that a problem occured...
}
}
}
}
/* Output clock on MCO2 pin(PC9) for debugging purpose */
//HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_1); // 84 MHz
}
#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0)
/******************************************************************************/
/* PLL (clocked by HSE) used as System clock source */
/******************************************************************************/
MBED_WEAK uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
{
RCC_ClkInitTypeDef RCC_ClkInitStruct;
RCC_OscInitTypeDef RCC_OscInitStruct;
/* The voltage scaling allows optimizing the power consumption when the device is
clocked below the maximum system frequency, to update the voltage scaling value
regarding system frequency refer to product datasheet. */
__HAL_RCC_PWR_CLK_ENABLE();
__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
/* Enable HSE oscillator and activate PLL with HSE as source */
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
if (bypass == 0) {
RCC_OscInitStruct.HSEState = RCC_HSE_ON; /* External 8 MHz xtal on OSC_IN/OSC_OUT */
} else {
RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; /* External 8 MHz clock on OSC_IN */
}
RCC_OscInitStruct.HSIState = RCC_HSI_OFF;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
RCC_OscInitStruct.PLL.PLLM = 8; // VCO input clock = 1 MHz (8 MHz / 8)
RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 168 MHz (336 MHz / 2)
RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> OK for USB
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
return 0; // FAIL
}
/* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 168 MHz
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 168 MHz
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 42 MHz
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 84 MHz (SPI1 clock...)
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
return 0; // FAIL
}
/* Output clock on MCO1 pin(PA8) for debugging purpose */
/*
if (bypass == 0)
HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz
else
HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz
*/
return 1; // OK
}
#endif
/******************************************************************************/
/* PLL (clocked by HSI) used as System clock source */
/******************************************************************************/
uint8_t SetSysClock_PLL_HSI(void)
{
RCC_ClkInitTypeDef RCC_ClkInitStruct;
RCC_OscInitTypeDef RCC_OscInitStruct;
/* The voltage scaling allows optimizing the power consumption when the device is
clocked below the maximum system frequency, to update the voltage scaling value
regarding system frequency refer to product datasheet. */
__HAL_RCC_PWR_CLK_ENABLE();
__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
/* Enable HSI oscillator and activate PLL with HSI as source */
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
RCC_OscInitStruct.HSIState = RCC_HSI_ON;
RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16)
RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336)
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 168 MHz (336 MHz / 2)
RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> freq is ok but not precise enough
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
return 0; // FAIL
}
/* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 168 MHz
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 168 MHz
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 42 MHz
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 84 MHz
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
return 0; // FAIL
}
/* Output clock on MCO1 pin(PA8) for debugging purpose */
//HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz
return 1; // OK
}
