/* mbed Microcontroller Library
* SPDX-License-Identifier: BSD-3-Clause
******************************************************************************
*
* Copyright (c) 2015-2021 STMicroelectronics.
* All rights reserved.
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/**
* This file configures the system clock as follows:
*-----------------------------------------------------------------------------------
* System clock source | 1- USE_PLL_HSE_EXTC (external 8 MHz clock) |
* | 2- USE_PLL_HSE_XTAL (external 8 MHz xtal) | DEVICE_USBDEVICE=1
* | 3- USE_PLL_HSI (internal 16 MHz clock) |
*-----------------------------------------------------------------------------------
* SYSCLK(MHz) | 180 | 168
* AHBCLK (MHz) | 180 | 168
* APB1CLK (MHz) | 45 | 42
* APB2CLK (MHz) | 90 | 84
* USB capable (48 MHz) | NO | YES (HSI calibration needed)
*-----------------------------------------------------------------------------------
**/
#include "stm32f4xx.h"
#include "mbed_error.h"
// clock source is selected with CLOCK_SOURCE in json config
#define USE_PLL_HSE_EXTC 0x8 // Use external clock (ST Link MCO)
#define USE_PLL_HSE_XTAL 0x4 // Use external xtal (X3 on board - not provided by default)
#define USE_PLL_HSI 0x2 // Use HSI internal clock
#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
uint8_t SetSysClock_PLL_HSE(uint8_t bypass);
#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
#if ((CLOCK_SOURCE) & USE_PLL_HSI)
uint8_t SetSysClock_PLL_HSI(void);
#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
/**
* @brief Configures the System clock source, PLL Multiplier and Divider factors,
* AHB/APBx prescalers and Flash settings
* @note This function should be called only once the RCC clock configuration
* is reset to the default reset state (done in SystemInit() function).
* @param None
* @retval None
*/
MBED_WEAK void SetSysClock(void)
{
#if ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC)
/* 1- Try to start with HSE and external clock */
if (SetSysClock_PLL_HSE(1) == 0)
#endif
{
#if ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL)
/* 2- If fail try to start with HSE and external xtal */
if (SetSysClock_PLL_HSE(0) == 0)
#endif
{
#if ((CLOCK_SOURCE) & USE_PLL_HSI)
/* 3- If fail start with HSI clock */
if (SetSysClock_PLL_HSI() == 0)
#endif
{
{
error("SetSysClock failed\n");
}
}
}
}
}
#if ( ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) )
/******************************************************************************/
/* PLL (clocked by HSE) used as System clock source */
/******************************************************************************/
MBED_WEAK uint8_t SetSysClock_PLL_HSE(uint8_t bypass)
{
RCC_OscInitTypeDef RCC_OscInitStruct;
RCC_ClkInitTypeDef RCC_ClkInitStruct;
/* The voltage scaling allows optimizing the power consumption when the device is
clocked below the maximum system frequency, to update the voltage scaling value
regarding system frequency refer to product datasheet. */
__HAL_RCC_PWR_CLK_ENABLE();
__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
/* Get the Clocks configuration according to the internal RCC registers */
HAL_RCC_GetOscConfig(&RCC_OscInitStruct);
/* PLL could be already configured by bootlader */
if (RCC_OscInitStruct.PLL.PLLState != RCC_PLL_ON) {
// Enable HSE oscillator and activate PLL with HSE as source
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
if (bypass == 0) {
RCC_OscInitStruct.HSEState = RCC_HSE_ON; // External 8 MHz xtal on OSC_IN/OSC_OUT
} else {
RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; // External 8 MHz clock on OSC_IN
}
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
RCC_OscInitStruct.PLL.PLLM = 8;
#if (DEVICE_USBDEVICE)
RCC_OscInitStruct.PLL.PLLN = 336;
#else
RCC_OscInitStruct.PLL.PLLN = 360;
#endif
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // 180 MHz or 168 MHz if DEVICE_USBDEVICE defined
RCC_OscInitStruct.PLL.PLLQ = 7; // 48 MHz if DEVICE_USBDEVICE defined
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
return 0; // FAIL
}
}
// Activate the OverDrive to reach the 180 MHz Frequency
if (HAL_PWREx_EnableOverDrive() != HAL_OK) {
return 0; // FAIL
}
// Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 or 168 MHz
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 or 42 MHz
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 or 84 MHz
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
return 0; // FAIL
}
// HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
return 1;
}
#endif /* ((CLOCK_SOURCE) & USE_PLL_HSE_XTAL) || ((CLOCK_SOURCE) & USE_PLL_HSE_EXTC) */
#if ((CLOCK_SOURCE) & USE_PLL_HSI)
/******************************************************************************/
/* PLL (clocked by HSI) used as System clock source */
/******************************************************************************/
uint8_t SetSysClock_PLL_HSI(void)
{
RCC_OscInitTypeDef RCC_OscInitStruct;
RCC_ClkInitTypeDef RCC_ClkInitStruct;
/* The voltage scaling allows optimizing the power consumption when the device is
clocked below the maximum system frequency, to update the voltage scaling value
regarding system frequency refer to product datasheet. */
__HAL_RCC_PWR_CLK_ENABLE();
__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
// Enable HSI oscillator and activate PLL with HSI as source
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE;
RCC_OscInitStruct.HSIState = RCC_HSI_ON;
RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
RCC_OscInitStruct.PLL.PLLM = 8;
#if (DEVICE_USBDEVICE)
RCC_OscInitStruct.PLL.PLLN = 168;
#else
RCC_OscInitStruct.PLL.PLLN = 180;
#endif
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // 180 MHz or 168 MHz if DEVICE_USBDEVICE defined
RCC_OscInitStruct.PLL.PLLQ = 7; // 48 MHz if DEVICE_USBDEVICE defined
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
return 0; // FAIL
}
// Activate the OverDrive to reach the 180 MHz Frequency
if (HAL_PWREx_EnableOverDrive() != HAL_OK) {
return 0; // FAIL
}
/* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 180 or 168 MHz
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 45 or 42 MHz
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 90 or 84 MHz
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
return 0; // FAIL
}
// HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
return 1;
}
#endif /* ((CLOCK_SOURCE) & USE_PLL_HSI) */
