GitBucket
Newer
/**
******************************************************************************
* @file shci.h
* @author MCD Application Team
* @brief HCI command for the system channel
******************************************************************************
* @attention
*
* <h2><center>© Copyright (c) 2019 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __SHCI_H
#define __SHCI_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "mbox_def.h" /* Requested to expose the MB_WirelessFwInfoTable_t structure */
/* Exported types ------------------------------------------------------------*/
/* SYSTEM EVENT */
typedef enum
{
WIRELESS_FW_RUNNING = 0x00,
FUS_FW_RUNNING = 0x01,
} SHCI_SysEvt_Ready_Rsp_t;
/* ERROR CODES
*
* These error codes are detected on CPU2 side and are send back to the CPU1 via a system
* notification message. It is up to the application running on CPU1 to manage these errors
*
* These errors can be generated by all layers (low level driver, stack, framework infrastructure, etc..)
*/
typedef enum
{
ERR_BLE_INIT = 0, /* This event is currently not reported by the CPU2 */
ERR_THREAD_LLD_FATAL_ERROR = 125, /* The LLD driver used on 802_15_4 detected a fatal error */
ERR_THREAD_UNKNOWN_CMD = 126, /* The command send by the CPU1 to control the Thread stack is unknown */
ERR_ZIGBEE_UNKNOWN_CMD = 200, /* The command send by the CPU1 to control the Zigbee stack is unknown */
} SCHI_SystemErrCode_t;
#define SHCI_EVTCODE ( 0xFF )
#define SHCI_SUB_EVT_CODE_BASE ( 0x9200 )
/**
* THE ORDER SHALL NOT BE CHANGED TO GUARANTEE COMPATIBILITY WITH THE CPU1 DEFINITION
*/
typedef enum
{
SHCI_SUB_EVT_CODE_READY = SHCI_SUB_EVT_CODE_BASE,
SHCI_SUB_EVT_ERROR_NOTIF,
SHCI_SUB_EVT_BLE_NVM_RAM_UPDATE,
SHCI_SUB_EVT_THREAD_NVM_RAM_UPDATE,
SHCI_SUB_EVT_NVM_START_WRITE,
SHCI_SUB_EVT_NVM_END_WRITE,
SHCI_SUB_EVT_NVM_START_ERASE,
SHCI_SUB_EVT_NVM_END_ERASE,
SHCI_SUB_EVT_CODE_CONCURRENT_802154_EVT,
} SHCI_SUB_EVT_CODE_t;
/**
* SHCI_SUB_EVT_CODE_READY
* This notifies the CPU1 that the CPU2 is now ready to receive commands
* It reports as well which firmware is running on CPU2 : The wireless stack of the FUS (previously named RSS)
*/
typedef PACKED_STRUCT{
SHCI_SysEvt_Ready_Rsp_t sysevt_ready_rsp;
} SHCI_C2_Ready_Evt_t;
/**
* SHCI_SUB_EVT_ERROR_NOTIF
* This reports to the CPU1 some error form the CPU2
*/
typedef PACKED_STRUCT{
SCHI_SystemErrCode_t errorCode;
} SHCI_C2_ErrorNotif_Evt_t;
/**
* SHCI_SUB_EVT_BLE_NVM_RAM_UPDATE
* This notifies the CPU1 which part of the BLE NVM RAM has been updated so that only the modified
* section could be written in Flash/NVM
* StartAddress : Start address of the section that has been modified
* Size : Size (in bytes) of the section that has been modified
*/
typedef PACKED_STRUCT{
uint32_t StartAddress;
uint32_t Size;
} SHCI_C2_BleNvmRamUpdate_Evt_t;
/**
* SHCI_SUB_EVT_THREAD_NVM_RAM_UPDATE
* This notifies the CPU1 which part of the OT NVM RAM has been updated so that only the modified
* section could be written in Flash/NVM
* StartAddress : Start address of the section that has been modified
* Size : Size (in bytes) of the section that has been modified
*/
typedef PACKED_STRUCT{
uint32_t StartAddress;
uint32_t Size;
} SHCI_C2_ThreadNvmRamUpdate_Evt_t;
/**
* SHCI_SUB_EVT_NVM_START_WRITE
* This notifies the CPU1 that the CPU2 has started a write procedure in Flash
* NumberOfWords : The number of 64bits data the CPU2 needs to write in Flash.
* For each 64bits data, the algorithm as described in AN5289 is executed.
* When this number is reported to 0, it means the Number of 64bits to be written
* was unknown when the procedure has started.
* When all data are written, the SHCI_SUB_EVT_NVM_END_WRITE event is reported
*/
typedef PACKED_STRUCT{
uint32_t NumberOfWords;
} SHCI_C2_NvmStartWrite_Evt_t;
/**
* SHCI_SUB_EVT_NVM_END_WRITE
* This notifies the CPU1 that the CPU2 has written all expected data in Flash
*/
/**
* SHCI_SUB_EVT_NVM_START_ERASE
* This notifies the CPU1 that the CPU2 has started a erase procedure in Flash
* NumberOfSectors : The number of sectors the CPU2 needs to erase in Flash.
* For each sector, the algorithm as described in AN5289 is executed.
* When this number is reported to 0, it means the Number of sectors to be erased
* was unknown when the procedure has started.
* When all sectors are erased, the SHCI_SUB_EVT_NVM_END_ERASE event is reported
*/
typedef PACKED_STRUCT{
uint32_t NumberOfSectors;
} SHCI_C2_NvmStartErase_Evt_t;
/**
* SHCI_SUB_EVT_NVM_END_ERASE
* This notifies the CPU1 that the CPU2 has erased all expected flash sectors
*/
/* SYSTEM COMMAND */
typedef PACKED_STRUCT
{
/**
* MetaData holds :
* 2*32bits for chaining list
* 1*32bits with BLE header (type + Opcode + Length)
*/
uint32_t MetaData[3];
} SHCI_Header_t;
typedef enum
{
SHCI_Success = 0x00,
SHCI_UNKNOWN_CMD = 0x01,
SHCI_ERR_UNSUPPORTED_FEATURE = 0x11,
SHCI_ERR_INVALID_HCI_CMD_PARAMS = 0x12,
SHCI_ERR_INVALID_PARAMS = 0x42,
SHCI_FUS_CMD_NOT_SUPPORTED = 0xFF,
} SHCI_CmdStatus_t;
typedef enum
{
SHCI_8BITS = 0x01,
SHCI_16BITS = 0x02,
SHCI_32BITS = 0x04,
} SHCI_Busw_t;
#define SHCI_OGF ( 0x3F )
#define SHCI_OCF_BASE ( 0x50 )
/**
* THE ORDER SHALL NOT BE CHANGED TO GUARANTEE COMPATIBILITY WITH THE CPU2 DEFINITION
*/
typedef enum
{
SHCI_OCF_C2_RESERVED1 = SHCI_OCF_BASE,
SHCI_OCF_C2_RESERVED2,
SHCI_OCF_C2_FUS_GET_STATE,
SHCI_OCF_C2_FUS_RESERVED1,
SHCI_OCF_C2_FUS_FW_UPGRADE,
SHCI_OCF_C2_FUS_FW_DELETE,
SHCI_OCF_C2_FUS_UPDATE_AUTH_KEY,
SHCI_OCF_C2_FUS_LOCK_AUTH_KEY,
SHCI_OCF_C2_FUS_STORE_USR_KEY,
SHCI_OCF_C2_FUS_LOAD_USR_KEY,
SHCI_OCF_C2_FUS_START_WS,
SHCI_OCF_C2_FUS_RESERVED2,
SHCI_OCF_C2_FUS_RESERVED3,
SHCI_OCF_C2_FUS_LOCK_USR_KEY,
SHCI_OCF_C2_FUS_UNLOAD_USR_KEY,
SHCI_OCF_C2_FUS_ACTIVATE_ANTIROLLBACK,
SHCI_OCF_C2_FUS_RESERVED7,
SHCI_OCF_C2_FUS_RESERVED8,
SHCI_OCF_C2_FUS_RESERVED9,
SHCI_OCF_C2_FUS_RESERVED10,
SHCI_OCF_C2_FUS_RESERVED11,
SHCI_OCF_C2_FUS_RESERVED12,
SHCI_OCF_C2_BLE_INIT,
SHCI_OCF_C2_THREAD_INIT,
SHCI_OCF_C2_DEBUG_INIT,
SHCI_OCF_C2_FLASH_ERASE_ACTIVITY,
SHCI_OCF_C2_CONCURRENT_SET_MODE,
SHCI_OCF_C2_FLASH_STORE_DATA,
SHCI_OCF_C2_FLASH_ERASE_DATA,
SHCI_OCF_C2_RADIO_ALLOW_LOW_POWER,
SHCI_OCF_C2_MAC_802_15_4_INIT,
SHCI_OCF_C2_REINIT,
SHCI_OCF_C2_ZIGBEE_INIT,
SHCI_OCF_C2_LLD_TESTS_INIT,
SHCI_OCF_C2_EXTPA_CONFIG,
SHCI_OCF_C2_SET_FLASH_ACTIVITY_CONTROL,
SHCI_OCF_C2_BLE_LLD_INIT,
SHCI_OCF_C2_CONFIG,
SHCI_OCF_C2_CONCURRENT_GET_NEXT_BLE_EVT_TIME,
SHCI_OCF_C2_CONCURRENT_ENABLE_NEXT_802154_EVT_NOTIFICATION,
SHCI_OCF_C2_802_15_4_DEINIT,
} SHCI_OCF_t;
#define SHCI_OPCODE_C2_FUS_GET_STATE (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_GET_STATE)
/** No command parameters */
/** Response parameters*/
/** It responds a 1 byte value holding FUS State error code when the FUS State value is 0xFF (FUS_STATE_VALUE_ERROR) */
typedef enum
{
FUS_STATE_ERROR_NO_ERROR = 0x00,
FUS_STATE_ERROR_IMG_NOT_FOUND = 0x01,
FUS_STATE_ERROR_IMG_CORRUPT = 0x02,
FUS_STATE_ERROR_IMG_NOT_AUTHENTIC = 0x03,
FUS_STATE_ERROR_IMG_NOT_ENOUGH_SPACE = 0x04,
FUS_STATE_ERROR_IMAGE_USRABORT = 0x05,
FUS_STATE_ERROR_IMAGE_ERSERROR = 0x06,
FUS_STATE_ERROR_IMAGE_WRTERROR = 0x07,
FUS_STATE_ERROR_AUTH_TAG_ST_NOTFOUND = 0x08,
FUS_STATE_ERROR_AUTH_TAG_CUST_NOTFOUND = 0x09,
FUS_STATE_ERROR_AUTH_KEY_LOCKED = 0x0A,
FUS_STATE_ERROR_FW_ROLLBACK_ERROR = 0x11,
FUS_STATE_ERROR_STATE_NOT_RUNNING = 0xFE,
FUS_STATE_ERROR_ERR_UNKNOWN = 0xFF,
} SHCI_FUS_GetState_ErrorCode_t;
enum
{
FUS_STATE_VALUE_IDLE = 0x00,
FUS_STATE_VALUE_FW_UPGRD_ONGOING = 0x10,
FUS_STATE_VALUE_FW_UPGRD_ONGOING_END = 0x1F, /* All values between 0x10 and 0x1F has the same meaning */
FUS_STATE_VALUE_FUS_UPGRD_ONGOING = 0x20,
FUS_STATE_VALUE_FUS_UPGRD_ONGOING_END = 0x2F, /* All values between 0x20 and 0x2F has the same meaning */
FUS_STATE_VALUE_SERVICE_ONGOING = 0x30,
FUS_STATE_VALUE_SERVICE_ONGOING_END = 0x3F, /* All values between 0x30 and 0x3F has the same meaning */
FUS_STATE_VALUE_ERROR = 0xFF,
};
#define SHCI_OPCODE_C2_FUS_RESERVED1 (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_RESERVED1)
/** No command parameters */
/** No response parameters*/
#define SHCI_OPCODE_C2_FUS_FW_UPGRADE (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_FW_UPGRADE)
/** No structure for command parameters */
/** No response parameters*/
#define SHCI_OPCODE_C2_FUS_FW_DELETE (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_FW_DELETE)
/** No command parameters */
/** No response parameters*/
#define SHCI_OPCODE_C2_FUS_UPDATE_AUTH_KEY (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_UPDATE_AUTH_KEY)
typedef PACKED_STRUCT{
uint8_t KeySize;
uint8_t KeyData[64];
} SHCI_C2_FUS_UpdateAuthKey_Cmd_Param_t;
/** No response parameters*/
#define SHCI_OPCODE_C2_FUS_LOCK_AUTH_KEY (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_LOCK_AUTH_KEY)
/** No command parameters */
/** No response parameters*/
#define SHCI_OPCODE_C2_FUS_STORE_USR_KEY (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_STORE_USR_KEY)
/** Command parameters */
/* List of supported key type */
enum
{
KEYTYPE_NONE = 0x00,
KEYTYPE_SIMPLE = 0x01,
KEYTYPE_MASTER = 0x02,
KEYTYPE_ENCRYPTED = 0x03,
};
/* List of supported key size */
enum
{
KEYSIZE_16 = 16,
KEYSIZE_32 = 32,
};
typedef PACKED_STRUCT{
uint8_t KeyType;
uint8_t KeySize;
uint8_t KeyData[32 + 12];
} SHCI_C2_FUS_StoreUsrKey_Cmd_Param_t;
/** Response parameters*/
/** It responds a 1 byte value holding the index given for the stored key */
#define SHCI_OPCODE_C2_FUS_LOAD_USR_KEY (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_LOAD_USR_KEY)
/** Command parameters */
/** 1 byte holding the key index value */
/** No response parameters*/
#define SHCI_OPCODE_C2_FUS_START_WS (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_START_WS)
/** No command parameters */
/** No response parameters*/
#define SHCI_OPCODE_C2_FUS_RESERVED2 (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_RESERVED2)
/** No command parameters */
/** No response parameters*/
#define SHCI_OPCODE_C2_FUS_RESERVED3 (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_RESERVED3)
/** No command parameters */
/** No response parameters*/
#define SHCI_OPCODE_C2_FUS_LOCK_USR_KEY (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_LOCK_USR_KEY)
/** Command parameters */
/** 1 byte holding the key index value */
/** No response parameters*/
#define SHCI_OPCODE_C2_FUS_UNLOAD_USR_KEY (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_UNLOAD_USR_KEY)
/** No command parameters */
/** 1 byte holding the key index value */
#define SHCI_OPCODE_C2_FUS_ACTIVATE_ANTIROLLBACK (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_ACTIVATE_ANTIROLLBACK)
/** No command parameters */
/** No response parameters*/
#define SHCI_OPCODE_C2_FUS_RESERVED7 (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_RESERVED7)
/** No command parameters */
/** No response parameters*/
#define SHCI_OPCODE_C2_FUS_RESERVED8 (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_RESERVED8)
/** No command parameters */
/** No response parameters*/
#define SHCI_OPCODE_C2_FUS_RESERVED9 (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_RESERVED9)
/** No command parameters */
/** No response parameters*/
#define SHCI_OPCODE_C2_FUS_RESERVED10 (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_RESERVED10)
/** No command parameters */
/** No response parameters*/
#define SHCI_OPCODE_C2_FUS_RESERVED11 (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_RESERVED11)
/** No command parameters */
/** No response parameters*/
#define SHCI_OPCODE_C2_FUS_RESERVED12 (( SHCI_OGF << 10) + SHCI_OCF_C2_FUS_RESERVED12)
/** No command parameters */
/** No response parameters*/
#define SHCI_OPCODE_C2_BLE_INIT (( SHCI_OGF << 10) + SHCI_OCF_C2_BLE_INIT)
/** THE ORDER SHALL NOT BE CHANGED */
typedef PACKED_STRUCT{
uint8_t* pBleBufferAddress; /**< NOT USED - shall be set to 0 */
uint32_t BleBufferSize; /**< NOT USED - shall be set to 0 */
/**
* NumAttrRecord
* Maximum number of attribute records related to all the required characteristics (excluding the services)
* that can be stored in the GATT database, for the specific BLE user application.
* For each characteristic, the number of attribute records goes from two to five depending on the characteristic properties:
* - minimum of two (one for declaration and one for the value)
* - add one more record for each additional property: notify or indicate, broadcast, extended property.
* The total calculated value must be increased by 9, due to the records related to the standard attribute profile and
* GAP service characteristics, and automatically added when initializing GATT and GAP layers
* - Min value: <number of user attributes> + 9
* - Max value: depending on the GATT database defined by user application
*/
uint16_t NumAttrRecord;
/**
* NumAttrServ
* Defines the maximum number of services that can be stored in the GATT database. Note that the GAP and GATT services
* are automatically added at initialization so this parameter must be the number of user services increased by two.
* - Min value: <number of user service> + 2
* - Max value: depending GATT database defined by user application
*/
uint16_t NumAttrServ;
/**
* AttrValueArrSize
* NOTE: This parameter is ignored by the CPU2 when the parameter "Options" is set to "LL_only" ( see Options description in that structure )
*
* Size of the storage area for the attribute values.
* Each characteristic contributes to the attrValueArrSize value as follows:
* - Characteristic value length plus:
* + 5 bytes if characteristic UUID is 16 bits
* + 19 bytes if characteristic UUID is 128 bits
* + 2 bytes if characteristic has a server configuration descriptor
* + 2 bytes * NumOfLinks if the characteristic has a client configuration descriptor
* + 2 bytes if the characteristic has extended properties
* Each descriptor contributes to the attrValueArrSize value as follows:
* - Descriptor length
*/
uint16_t AttrValueArrSize;
/**
* NumOfLinks
* Maximum number of BLE links supported
* - Min value: 1
* - Max value: 8
*/
uint8_t NumOfLinks;
/**
* ExtendedPacketLengthEnable
* Disable/enable the extended packet length BLE 5.0 feature
* - Disable: 0
* - Enable: 1
*/
uint8_t ExtendedPacketLengthEnable;
/**
* PrWriteListSize
* NOTE: This parameter is ignored by the CPU2 when the parameter "Options" is set to "LL_only" ( see Options description in that structure )
*
* Maximum number of supported prepare write request
* - Min value: given by the macro DEFAULT_PREP_WRITE_LIST_SIZE
* - Max value: a value higher than the minimum required can be specified, but it is not recommended
*/
uint8_t PrWriteListSize;
/**
* MblockCount
* NOTE: This parameter is overwritten by the CPU2 with an hardcoded optimal value when the parameter "Options" is set to "LL_only"
* ( see Options description in that structure )
*
* Number of allocated memory blocks for the BLE stack
* - Min value: given by the macro MBLOCKS_CALC
* - Max value: a higher value can improve data throughput performance, but uses more memory
*/
uint8_t MblockCount;
/**
* AttMtu
* NOTE: This parameter is ignored by the CPU2 when the parameter "Options" is set to "LL_only" ( see Options description in that structure )
*
* Maximum ATT MTU size supported
* - Min value: 23
* - Max value: 512
*/
uint16_t AttMtu;
/**
* SlaveSca
* The sleep clock accuracy (ppm value) that used in BLE connected slave mode to calculate the window widening
* (in combination with the sleep clock accuracy sent by master in CONNECT_REQ PDU),
* refer to BLE 5.0 specifications - Vol 6 - Part B - chap 4.5.7 and 4.2.2
* - Min value: 0
* - Max value: 500 (worst possible admitted by specification)
*/
uint16_t SlaveSca;
/**
* MasterSca
* The sleep clock accuracy handled in master mode. It is used to determine the connection and advertising events timing.
* It is transmitted to the slave in CONNEC_REQ PDU used by the slave to calculate the window widening,
* see SlaveSca and Bluetooth Core Specification v5.0 Vol 6 - Part B - chap 4.5.7 and 4.2.2
* Possible values:
* - 251 ppm to 500 ppm: 0
* - 151 ppm to 250 ppm: 1
* - 101 ppm to 150 ppm: 2
* - 76 ppm to 100 ppm: 3
* - 51 ppm to 75 ppm: 4
* - 31 ppm to 50 ppm: 5
* - 21 ppm to 30 ppm: 6
* - 0 ppm to 20 ppm: 7
*/
uint8_t MasterSca;
/**
* LsSource
* Source for the 32 kHz slow speed clock.
* - External crystal LSE: 0 - No calibration
* - Others:1 - As the accuracy of this oscillator can vary depending upon external conditions (temperature),
* it is calibrated every second to ensure correct behavior of timing sensitive BLE operations
*/
uint8_t LsSource;
/**
* MaxConnEventLength
* This parameter determines the maximum duration of a slave connection event. When this duration is reached the slave closes
* the current connections event (whatever is the CE_length parameter specified by the master in HCI_CREATE_CONNECTION HCI command),
* expressed in units of 625/256 µs (~2.44 µs)
* - Min value: 0 (if 0 is specified, the master and slave perform only a single TX-RX exchange per connection event)
* - Max value: 1638400 (4000 ms). A higher value can be specified (max 0xFFFFFFFF) but results in a maximum connection time
* of 4000 ms as specified. In this case the parameter is not applied, and the predicted CE length calculated on slave is not shortened
*/
uint32_t MaxConnEventLength;
/**
* HsStartupTime
* Startup time of the high speed (16 or 32 MHz) crystal oscillator in units of 625/256 µs (~2.44 µs).
* - Min value: 0
* - Max value: 820 (~2 ms). A higher value can be specified, but the value that implemented in stack is forced to ~2 ms
*/
uint16_t HsStartupTime;
/**
* ViterbiEnable
* Viterbi implementation in BLE LL reception.
* - 0: Enable
* - 1: Disable
*/
uint8_t ViterbiEnable;
/**
* Options flags
* - bit 0: 1: LL only 0: LL + host
* - bit 1: 1: no service change desc. 0: with service change desc.
* - bit 2: 1: device name Read-Only 0: device name R/W
* - bit 7: 1: LE Power Class 1 0: LE Power Classe 2-3
* - other bits: reserved ( shall be set to 0)
*/
uint8_t Options;
/**
* HwVersion
* Reserved for future use - shall be set to 0
*/
uint8_t HwVersion;
/**
* Maximum number of connection-oriented channels in initiator mode.
* Range: 0 .. 64
*/
uint8_t max_coc_initiator_nbr;
/**
* Minimum transmit power in dBm supported by the Controller.
* Range: -127 .. 20
*/
int8_t min_tx_power;
/**
* Maximum transmit power in dBm supported by the Controller.
* Range: -127 .. 20
*/
int8_t max_tx_power;
} SHCI_C2_Ble_Init_Cmd_Param_t;
typedef PACKED_STRUCT{
SHCI_Header_t Header; /** Does not need to be initialized by the user */
SHCI_C2_Ble_Init_Cmd_Param_t Param;
} SHCI_C2_Ble_Init_Cmd_Packet_t;
/**
* Options
* Each definition below may be added together to build the Options value
* WARNING : Only one definition per bit shall be added to build the Options value
*/
#define SHCI_C2_BLE_INIT_OPTIONS_LL_ONLY (1<<0)
#define SHCI_C2_BLE_INIT_OPTIONS_LL_HOST (0<<0)
#define SHCI_C2_BLE_INIT_OPTIONS_NO_SVC_CHANGE_DESC (1<<1)
#define SHCI_C2_BLE_INIT_OPTIONS_WITH_SVC_CHANGE_DESC (0<<1)
#define SHCI_C2_BLE_INIT_OPTIONS_DEVICE_NAME_RO (1<<2)
#define SHCI_C2_BLE_INIT_OPTIONS_DEVICE_NAME_RW (0<<2)
#define SHCI_C2_BLE_INIT_OPTIONS_POWER_CLASS_1 (1<<7)
#define SHCI_C2_BLE_INIT_OPTIONS_POWER_CLASS_2_3 (0<<7)
#define SHCI_OPCODE_C2_THREAD_INIT (( SHCI_OGF << 10) + SHCI_OCF_C2_THREAD_INIT)
/** No command parameters */
/** No response parameters*/
#define SHCI_OPCODE_C2_DEBUG_INIT (( SHCI_OGF << 10) + SHCI_OCF_C2_DEBUG_INIT)
/** Command parameters */
typedef PACKED_STRUCT
{
uint8_t thread_config;
uint8_t ble_config;
uint8_t mac_802_15_4_config;
uint8_t zigbee_config;
} SHCI_C2_DEBUG_TracesConfig_t;
typedef PACKED_STRUCT
{
uint8_t ble_dtb_cfg;
uint8_t reserved[3];
} SHCI_C2_DEBUG_GeneralConfig_t;
typedef PACKED_STRUCT{
uint8_t *pGpioConfig;
uint8_t *pTracesConfig;
uint8_t *pGeneralConfig;
uint8_t GpioConfigSize;
uint8_t TracesConfigSize;
uint8_t GeneralConfigSize;
} SHCI_C2_DEBUG_init_Cmd_Param_t;
typedef PACKED_STRUCT{
SHCI_Header_t Header; /** Does not need to be initialized by the user */
SHCI_C2_DEBUG_init_Cmd_Param_t Param;
} SHCI_C2_DEBUG_Init_Cmd_Packet_t;
/** No response parameters*/
#define SHCI_OPCODE_C2_FLASH_ERASE_ACTIVITY (( SHCI_OGF << 10) + SHCI_OCF_C2_FLASH_ERASE_ACTIVITY)
/** Command parameters */
typedef enum
{
ERASE_ACTIVITY_OFF = 0x00,
ERASE_ACTIVITY_ON = 0x01,
} SHCI_EraseActivity_t;
/** No response parameters*/
#define SHCI_OPCODE_C2_CONCURRENT_SET_MODE (( SHCI_OGF << 10) + SHCI_OCF_C2_CONCURRENT_SET_MODE)
/** command parameters */
typedef enum
{
BLE_ENABLE,
THREAD_ENABLE,
ZIGBEE_ENABLE,
MAC_ENABLE,
} SHCI_C2_CONCURRENT_Mode_Param_t;
/** No response parameters*/
#define SHCI_OPCODE_C2_CONCURRENT_GET_NEXT_BLE_EVT_TIME (( SHCI_OGF << 10) + SHCI_OCF_C2_CONCURRENT_GET_NEXT_BLE_EVT_TIME)
/** command parameters */
typedef PACKED_STRUCT
{
uint32_t relative_time;
} SHCI_C2_CONCURRENT_GetNextBleEvtTime_Param_t;
/** No response parameters*/
#define SHCI_OPCODE_C2_CONCURRENT_ENABLE_NEXT_802154_EVT_NOTIFICATION (( SHCI_OGF << 10) + SHCI_OCF_C2_CONCURRENT_ENABLE_NEXT_802154_EVT_NOTIFICATION)
/** No command parameters */
/** No response parameters*/
#define SHCI_OPCODE_C2_FLASH_STORE_DATA (( SHCI_OGF << 10) + SHCI_OCF_C2_FLASH_STORE_DATA)
#define SHCI_OPCODE_C2_FLASH_ERASE_DATA (( SHCI_OGF << 10) + SHCI_OCF_C2_FLASH_ERASE_DATA)
/** command parameters */
typedef enum
{
BLE_IP,
THREAD_IP,
ZIGBEE_IP,
} SHCI_C2_FLASH_Ip_t;
/** No response parameters*/
#define SHCI_OPCODE_C2_RADIO_ALLOW_LOW_POWER (( SHCI_OGF << 10) + SHCI_OCF_C2_RADIO_ALLOW_LOW_POWER)
#define SHCI_OPCODE_C2_MAC_802_15_4_INIT (( SHCI_OGF << 10) + SHCI_OCF_C2_MAC_802_15_4_INIT)
#define SHCI_OPCODE_C2_REINIT (( SHCI_OGF << 10) + SHCI_OCF_C2_REINIT)
#define SHCI_OPCODE_C2_ZIGBEE_INIT (( SHCI_OGF << 10) + SHCI_OCF_C2_ZIGBEE_INIT)
#define SHCI_OPCODE_C2_LLD_TESTS_INIT (( SHCI_OGF << 10) + SHCI_OCF_C2_LLD_TESTS_INIT)
#define SHCI_OPCODE_C2_BLE_LLD_INIT (( SHCI_OGF << 10) + SHCI_OCF_C2_BLE_LLD_INIT)
#define SHCI_OPCODE_C2_EXTPA_CONFIG (( SHCI_OGF << 10) + SHCI_OCF_C2_EXTPA_CONFIG)
/** Command parameters */
enum
{
EXT_PA_ENABLED_LOW,
EXT_PA_ENABLED_HIGH,
}/* gpio_polarity */;
enum
{
EXT_PA_DISABLED,
EXT_PA_ENABLED,
}/* gpio_status */;
typedef PACKED_STRUCT{
uint32_t gpio_port;
uint16_t gpio_pin_number;
uint8_t gpio_polarity;
uint8_t gpio_status;
} SHCI_C2_EXTPA_CONFIG_Cmd_Param_t;
/** No response parameters*/
#define SHCI_OPCODE_C2_SET_FLASH_ACTIVITY_CONTROL (( SHCI_OGF << 10) + SHCI_OCF_C2_SET_FLASH_ACTIVITY_CONTROL)
/** Command parameters */
typedef enum
{
FLASH_ACTIVITY_CONTROL_PES,
FLASH_ACTIVITY_CONTROL_SEM7,
}SHCI_C2_SET_FLASH_ACTIVITY_CONTROL_Source_t;
/** No response parameters*/
#define SHCI_OPCODE_C2_CONFIG (( SHCI_OGF << 10) + SHCI_OCF_C2_CONFIG)
/** Command parameters */
typedef PACKED_STRUCT{
uint8_t PayloadCmdSize;
uint8_t Config1;
uint8_t EvtMask1;
uint8_t Spare1;
uint32_t BleNvmRamAddress;
uint32_t ThreadNvmRamAddress;
} SHCI_C2_CONFIG_Cmd_Param_t;
#define SHCI_OPCODE_C2_802_15_4_DEINIT (( SHCI_OGF << 10) + SHCI_OCF_C2_802_15_4_DEINIT)
/**
* PayloadCmdSize
* Value that shall be used
*/
#define SHCI_C2_CONFIG_PAYLOAD_CMD_SIZE (sizeof(SHCI_C2_CONFIG_Cmd_Param_t) - 1)
/**
* Config1
* Each definition below may be added together to build the Config1 value
* WARNING : Only one definition per bit shall be added to build the Config1 value
*/
#define SHCI_C2_CONFIG_CONFIG1_BIT0_BLE_NVM_DATA_TO_INTERNAL_FLASH (0<<0)
#define SHCI_C2_CONFIG_CONFIG1_BIT0_BLE_NVM_DATA_TO_SRAM (1<<0)
#define SHCI_C2_CONFIG_CONFIG1_BIT1_THREAD_NVM_DATA_TO_INTERNAL_FLASH (0<<1)
#define SHCI_C2_CONFIG_CONFIG1_BIT1_THREAD_NVM_DATA_TO_SRAM (1<<1)
/**
* EvtMask1
* Each definition below may be added together to build the EvtMask1 value
*/
#define SHCI_C2_CONFIG_EVTMASK1_BIT0_ERROR_NOTIF_ENABLE (1<<0)
#define SHCI_C2_CONFIG_EVTMASK1_BIT1_BLE_NVM_RAM_UPDATE_ENABLE (1<<1)
#define SHCI_C2_CONFIG_EVTMASK1_BIT2_THREAD_NVM_RAM_UPDATE_ENABLE (1<<2)
#define SHCI_C2_CONFIG_EVTMASK1_BIT3_NVM_START_WRITE_ENABLE (1<<3)
#define SHCI_C2_CONFIG_EVTMASK1_BIT4_NVM_END_WRITE_ENABLE (1<<4)
#define SHCI_C2_CONFIG_EVTMASK1_BIT5_NVM_START_ERASE_ENABLE (1<<5)
#define SHCI_C2_CONFIG_EVTMASK1_BIT6_NVM_END_ERASE_ENABLE (1<<6)
/**
* BleNvmRamAddress
* The buffer shall have a size of BLE_NVM_SRAM_SIZE number of 32bits
* The buffer shall be allocated in SRAM2
*/
#define BLE_NVM_SRAM_SIZE (507)
/**
* ThreadNvmRamAddress
* The buffer shall have a size of THREAD_NVM_SRAM_SIZE number of 32bits
* The buffer shall be allocated in SRAM2
*/
#define THREAD_NVM_SRAM_SIZE (1016)
/** No response parameters*/
/* Exported type --------------------------------------------------------*/
#define FUS_DEVICE_INFO_TABLE_VALIDITY_KEYWORD (0xA94656B9)
/*
* At startup, the informations relative to the wireless binary are stored in RAM trough a structure defined by
* MB_WirelessFwInfoTable_t.This structure contains 4 fields (Version,MemorySize, Stack_info and a reserved part)
* each of those coded on 32 bits as shown on the table below:
*
*
* |7 |6 |5 |4 |3 |2 |1 |0 |7 |6 |5 |4 |3 |2 |1 |0 |7 |6 |5 |4 |3 |2 |1 |0 |7 |6 |5 |4 |3 |2 |1 |0 |
* -------------------------------------------------------------------------------------------------
* Version | Major version | Minor version | Sub version | Branch |ReleaseType|
* -------------------------------------------------------------------------------------------------
* MemorySize | SRAM2B (kB) | SRAM2A (kB) | SRAM1 (kB) | FLASH (4kb) |
* -------------------------------------------------------------------------------------------------
* Info stack | Reserved | Reserved | Reserved | Type (MAC,Thread,BLE) |
* -------------------------------------------------------------------------------------------------
* Reserved | Reserved | Reserved | Reserved | Reserved |
* -------------------------------------------------------------------------------------------------
*
*/
/* Field Version */
#define INFO_VERSION_MAJOR_OFFSET 24
#define INFO_VERSION_MAJOR_MASK 0xff000000
#define INFO_VERSION_MINOR_OFFSET 16
#define INFO_VERSION_MINOR_MASK 0x00ff0000
#define INFO_VERSION_SUB_OFFSET 8
#define INFO_VERSION_SUB_MASK 0x0000ff00
#define INFO_VERSION_BRANCH_OFFSET 4
#define INFO_VERSION_BRANCH_MASK 0x0000000f0
#define INFO_VERSION_TYPE_OFFSET 0
#define INFO_VERSION_TYPE_MASK 0x00000000f
#define INFO_VERSION_TYPE_RELEASE 1
/* Field Memory */
#define INFO_SIZE_SRAM2B_OFFSET 24
#define INFO_SIZE_SRAM2B_MASK 0xff000000
#define INFO_SIZE_SRAM2A_OFFSET 16
#define INFO_SIZE_SRAM2A_MASK 0x00ff0000
#define INFO_SIZE_SRAM1_OFFSET 8
#define INFO_SIZE_SRAM1_MASK 0x0000ff00
#define INFO_SIZE_FLASH_OFFSET 0
#define INFO_SIZE_FLASH_MASK 0x000000ff
/* Field stack information */
#define INFO_STACK_TYPE_OFFSET 0
#define INFO_STACK_TYPE_MASK 0x000000ff
#define INFO_STACK_TYPE_NONE 0
#define INFO_STACK_TYPE_BLE_FULL 0x01
#define INFO_STACK_TYPE_BLE_HCI 0x02
#define INFO_STACK_TYPE_BLE_LIGHT 0x03
#define INFO_STACK_TYPE_BLE_BEACON 0x04
#define INFO_STACK_TYPE_THREAD_FTD 0x10
#define INFO_STACK_TYPE_THREAD_MTD 0x11
#define INFO_STACK_TYPE_ZIGBEE_FFD 0x30
#define INFO_STACK_TYPE_ZIGBEE_RFD 0x31
#define INFO_STACK_TYPE_MAC 0x40
#define INFO_STACK_TYPE_BLE_THREAD_FTD_STATIC 0x50
#define INFO_STACK_TYPE_BLE_THREAD_FTD_DYAMIC 0x51
#define INFO_STACK_TYPE_802154_LLD_TESTS 0x60
#define INFO_STACK_TYPE_802154_PHY_VALID 0x61
#define INFO_STACK_TYPE_BLE_PHY_VALID 0x62
#define INFO_STACK_TYPE_BLE_LLD_TESTS 0x63
#define INFO_STACK_TYPE_BLE_RLV 0x64
#define INFO_STACK_TYPE_802154_RLV 0x65
#define INFO_STACK_TYPE_BLE_ZIGBEE_FFD_STATIC 0x70
#define INFO_STACK_TYPE_BLE_ZIGBEE_RFD_STATIC 0x71
#define INFO_STACK_TYPE_BLE_ZIGBEE_FFD_DYNAMIC 0x78
#define INFO_STACK_TYPE_BLE_ZIGBEE_RFD_DYNAMIC 0x79
#define INFO_STACK_TYPE_RLV 0x80
#define INFO_STACK_TYPE_BLE_MAC_STATIC 0x90
typedef struct {
/**
* Wireless Info
*/
uint8_t VersionMajor;
uint8_t VersionMinor;
uint8_t VersionSub;
uint8_t VersionBranch;
uint8_t VersionReleaseType;
uint8_t MemorySizeSram2B; /*< Multiple of 1K */
uint8_t MemorySizeSram2A; /*< Multiple of 1K */
uint8_t MemorySizeSram1; /*< Multiple of 1K */
uint8_t MemorySizeFlash; /*< Multiple of 4K */
uint8_t StackType;
/**
* Fus Info
*/
uint8_t FusVersionMajor;
uint8_t FusVersionMinor;
uint8_t FusVersionSub;
uint8_t FusMemorySizeSram2B; /*< Multiple of 1K */
uint8_t FusMemorySizeSram2A; /*< Multiple of 1K */
uint8_t FusMemorySizeFlash; /*< Multiple of 4K */
}WirelessFwInfo_t;
/* Exported functions ------------------------------------------------------- */
/**
* SHCI_C2_FUS_GetState
* @brief Read the FUS State
* If the user is not interested by the Error code response, a null value may
* be passed as parameter
*
* Note: This command is fully supported only by the FUS.
* When the wireless firmware receives that command, it responds SHCI_FUS_CMD_NOT_SUPPORTED the first time.
* When the wireless firmware receives that command a second time, it reboots the full device with the FUS running on CPU2
*
* @param p_rsp : return the error code when the FUS State Value = 0xFF
* @retval FUS State Values
*/
uint8_t SHCI_C2_FUS_GetState( SHCI_FUS_GetState_ErrorCode_t *p_rsp );
/**
* SHCI_C2_FUS_FwUpgrade
* @brief Request the FUS to install the CPU2 firmware update
* Note: This command is only supported by the FUS.
*
* @param fw_src_add: Address of the firmware image location
* @param fw_dest_add: Address of the firmware destination
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_FUS_FwUpgrade( uint32_t fw_src_add, uint32_t fw_dest_add );
/**
* SHCI_C2_FUS_FwDelete
* @brief Delete the wireless stack on CPU2
* Note: This command is only supported by the FUS.
*
* @param None
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_FUS_FwDelete( void );
/**
* SHCI_C2_FUS_UpdateAuthKey
* @brief Request the FUS to update the authentication key
* Note: This command is only supported by the FUS.
*
* @param pCmdPacket
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_FUS_UpdateAuthKey( SHCI_C2_FUS_UpdateAuthKey_Cmd_Param_t *pParam );
/**
* SHCI_C2_FUS_LockAuthKey
* @brief Request the FUS to prevent any future update of the authentication key
* Note: This command is only supported by the FUS.
*
* @param None
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_FUS_LockAuthKey( void );
/**
* SHCI_C2_FUS_StoreUsrKey
* @brief Request the FUS to store the user key
* Note: This command is supported by both the FUS and the wireless stack.
*
* @param pParam : command parameter
* @param p_key_index : Index allocated by the FUS to the stored key
*
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_FUS_StoreUsrKey( SHCI_C2_FUS_StoreUsrKey_Cmd_Param_t *pParam, uint8_t *p_key_index );
/**
* SHCI_C2_FUS_LoadUsrKey
* @brief Request the FUS to load the user key into the AES
* Note: This command is supported by both the FUS and the wireless stack.
*
* @param key_index : index of the user key to load in AES1
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_FUS_LoadUsrKey( uint8_t key_index );
/**
* SHCI_C2_FUS_StartWs
* @brief Request the FUS to reboot on the wireless stack
* Note: This command is only supported by the FUS.
*
* @param None
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_FUS_StartWs( void );
/**
* SHCI_C2_FUS_LockUsrKey
* @brief Request the FUS to lock the user key so that it cannot be updated later on
* Note: This command is supported by both the FUS and the wireless stack.
*
* @param key_index : index of the user key to lock
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_FUS_LockUsrKey( uint8_t key_index );
/**
* SHCI_C2_FUS_UnloadUsrKey
* @brief Request the FUS to Unload the user key so that the CPU1 may use the AES with another Key
* Note: This command is supported by both the FUS and the wireless stack.
*
* @param key_index : index of the user key to unload
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_FUS_UnloadUsrKey( uint8_t key_index );
/**
* SHCI_C2_FUS_ActivateAntiRollback
* @brief Request the FUS to enable the AntiRollback feature so that it is not possible to update the wireless firmware
* with an older version than the current one.
* Note:
* - This command is only supported by the FUS.
* - Once this feature is enabled, it is not possible anymore to disable it.
*
* @param None
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_FUS_ActivateAntiRollback( void );
/**
* SHCI_C2_BLE_Init
* @brief Provides parameters and starts the BLE Stack
*
* @param pCmdPacket : Parameters are described SHCI_C2_Ble_Init_Cmd_Packet_t declaration
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_BLE_Init( SHCI_C2_Ble_Init_Cmd_Packet_t *pCmdPacket );
/**
* SHCI_C2_THREAD_Init
* @brief Starts the THREAD Stack
*
* @param None
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_THREAD_Init( void );
/**
* SHCI_C2_LLDTESTS_Init
* @brief Starts the LLD tests CLI
*
* @param param_size : Nb of bytes
* @param p_param : pointeur with data to give from M4 to M0
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_LLDTESTS_Init( uint8_t param_size, uint8_t * p_param );
/**
* SHCI_C2_BLE_LLD_Init
* @brief Starts the LLD tests BLE
*
* @param param_size : Nb of bytes
* @param p_param : pointeur with data to give from M4 to M0
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_BLE_LLD_Init( uint8_t param_size, uint8_t * p_param );
/**
* SHCI_C2_ZIGBEE_Init
* @brief Starts the Zigbee Stack
*
* @param None
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_ZIGBEE_Init( void );
/**
* SHCI_C2_DEBUG_Init
* @brief Starts the Traces
*
* @param None
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_DEBUG_Init( SHCI_C2_DEBUG_Init_Cmd_Packet_t *pCmdPacket );
/**
* SHCI_C2_FLASH_EraseActivity
* @brief Provides the information of the start and the end of a flash erase window on the CPU1
*
* @param erase_activity: Start/End of erase activity
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_FLASH_EraseActivity( SHCI_EraseActivity_t erase_activity );
/**
* SHCI_C2_CONCURRENT_SetMode
* @brief Enable/Disable Thread on CPU2 (M0+)
*
* @param Mode: BLE or Thread enable flag
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_CONCURRENT_SetMode( SHCI_C2_CONCURRENT_Mode_Param_t Mode );
/**
* SHCI_C2_CONCURRENT_GetNextBleEvtTime
* @brief Get the next BLE event date (relative time)
*
* @param Command Packet
* @retval None
*/
SHCI_CmdStatus_t SHCI_C2_CONCURRENT_GetNextBleEvtTime( SHCI_C2_CONCURRENT_GetNextBleEvtTime_Param_t *pParam );
/**
* SHCI_C2_CONCURRENT_EnableNext_802154_EvtNotification
* @brief Activate the next 802.15.4 event notification (one shot)
*
* @param None
* @retval None
*/
SHCI_CmdStatus_t SHCI_C2_CONCURRENT_EnableNext_802154_EvtNotification( void );
/**
* SHCI_C2_FLASH_StoreData
* @brief Store Data in Flash
*
* @param Ip: BLE or THREAD
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_FLASH_StoreData( SHCI_C2_FLASH_Ip_t Ip );
/**
* SHCI_C2_FLASH_EraseData
* @brief Erase Data in Flash
*
* @param Ip: BLE or THREAD
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_FLASH_EraseData( SHCI_C2_FLASH_Ip_t Ip );
/**
* SHCI_C2_RADIO_AllowLowPower
* @brief Allow or forbid IP_radio (802_15_4 or BLE) to enter in low power mode.
*
* @param Ip: BLE or 802_15_5
* @param FlagRadioLowPowerOn: True or false
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_RADIO_AllowLowPower( SHCI_C2_FLASH_Ip_t Ip,uint8_t FlagRadioLowPowerOn);
/**
* SHCI_C2_MAC_802_15_4_Init
* @brief Starts the MAC 802.15.4 on M0
*
* @param None
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_MAC_802_15_4_Init( void );
/**
* SHCI_GetWirelessFwInfo
* @brief This function read back the informations relative to the wireless binary loaded.
* Refer yourself to MB_WirelessFwInfoTable_t structure to get the significance
* of the different parameters returned.
* @param pWirelessInfo : Pointer to WirelessFwInfo_t.
*
* @retval SHCI_Success
*/
SHCI_CmdStatus_t SHCI_GetWirelessFwInfo( WirelessFwInfo_t* pWirelessInfo );
/**
* SHCI_C2_Reinit
* @brief This is required to allow the CPU1 to fake a set C2BOOT when it has already been set.
* In order to fake a C2BOOT, the CPU1 shall :
* - Send SHCI_C2_Reinit()
* - call SEV instruction
* WARNING:
* This function is intended to be used by the SBSFU
*
* @param None
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_Reinit( void );
/**
* SHCI_C2_ExtpaConfig
* @brief Send the Ext PA configuration
* When the CPU2 receives the command, it controls the Ext PA as requested by the configuration
* This configures only which IO is used to enable/disable the ExtPA and the associated polarity
* This command has no effect on the other IO that is used to control the mode of the Ext PA (Rx/Tx)
*
* @param gpio_port: GPIOx where x can be (A..F) to select the GPIO peripheral for STM32WBxx family
* @param gpio_pin_number: This parameter can be one of GPIO_PIN_x (= LL_GPIO_PIN_x) where x can be (0..15).
* @param gpio_polarity: This parameter can be either
* - EXT_PA_ENABLED_LOW: ExtPA is enabled when GPIO is low
* - EXT_PA_ENABLED_HIGH: ExtPA is enabled when GPIO is high
* @param gpio_status: This parameter can be either
* - EXT_PA_DISABLED: Stop driving the ExtPA
* - EXT_PA_ENABLED: Drive the ExtPA according to radio activity
* (ON before the Event and OFF at the end of the event)
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_ExtpaConfig(uint32_t gpio_port, uint16_t gpio_pin_number, uint8_t gpio_polarity, uint8_t gpio_status);
/**
* SHCI_C2_SetFlashActivityControl
* @brief Set the mechanism to be used on CPU2 to prevent the CPU1 to either write or erase in flash
*
* @param Source: It can be one of the following list
* - FLASH_ACTIVITY_CONTROL_PES : The CPU2 set the PES bit to prevent the CPU1 to either read or write in flash
* - FLASH_ACTIVITY_CONTROL_SEM7 : The CPU2 gets the semaphore 7 to prevent the CPU1 to either read or write in flash.
* This requires the CPU1 to first get semaphore 7 before erasing or writing the flash.
*
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_SetFlashActivityControl(SHCI_C2_SET_FLASH_ACTIVITY_CONTROL_Source_t Source);
/**
* SHCI_C2_Config
* @brief Send the system configuration to the CPU2
*
* @param pCmdPacket: address of the buffer holding following parameters
* uint8_t PayloadCmdSize : Size of the payload - shall be SHCI_C2_CONFIG_PAYLOAD_CMD_SIZE
* uint8_t Config1 :
* - bit0 : 0 - BLE NVM Data data are flushed in internal secure flash
* 1 - BLE NVM Data are written in SRAM cache pointed by BleNvmRamAddress
* - bit1 : 0 - THREAD NVM Data data are flushed in internal secure flash
* 1 - THREAD NVM Data are written in SRAM cache pointed by ThreadNvmRamAddress
* - bit2 to bit7 : Unused, shall be set to 0
* uint8_t EvtMask1 :
* When a bit is set to 0, the event is not reported
* bit0 : Asynchronous Event with Sub Evt Code 0x9201 (= SHCI_SUB_EVT_ERROR_NOTIF)
* ...
* bit31 : Asynchronous Event with Sub Evt Code 0x9220
* uint8_t Spare1 : Unused, shall be set to 0
* uint32_t BleNvmRamAddress :
* Only considered when Config1.bit0 = 1
* When set to 0, data are kept in internal SRAM on CPU2
* Otherwise, data are copied in the cache pointed by BleNvmRamAddress
* The size of the buffer shall be BLE_NVM_SRAM_SIZE (number of 32bits)
* The buffer shall be allocated in SRAM2
* uint32_t ThreadNvmRamAddress :
* Only considered when Config1.bit1 = 1
* When set to 0, data are kept in internal SRAM on CPU2
* Otherwise, data are copied in the cache pointed by ThreadNvmRamAddress
* The size of the buffer shall be THREAD_NVM_SRAM_SIZE (number of 32bits)
* The buffer shall be allocated in SRAM2
*
* Please check macro definition to be used for this function
* They are defined in this file next to the definition of SHCI_OPCODE_C2_CONFIG
*
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_Config(SHCI_C2_CONFIG_Cmd_Param_t *pCmdPacket);
/**
* SHCI_C2_802_15_4_DeInit
* @brief Deinit 802.15.4 layer (to be used before entering StandBy mode)
*
* @param None
* @retval Status
*/
SHCI_CmdStatus_t SHCI_C2_802_15_4_DeInit( void );
#ifdef __cplusplus
}
#endif
#endif /*__SHCI_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/