Merge pull request #1193 from jwerner-chromium/JW_coreboot ...

New console API and coreboot support [v4]

Merge pull request #1229 from manojkumar-arm/manojkumar-arm/ca72-aarch32-reset-fix ...

lib/cpus: fix branching in reset function for cortex-a72 AARCH32 mode

coreboot: Add support for CBMEM console ...

coreboot supports an in-memory console to store firmware logs even when
no serial console is available. It is widely supported by
coreboot-compatible bootloaders (including SeaBIOS and GRUB) and can be
read by the Linux kernel.

This patch allows BL31 to add its own log messages to this console. The
driver will be registered automatically if coreboot support is compiled
in and detects the presence of a console buffer in the coreboot tables.

Change-Id: I31254dfa0c2fdeb7454634134b5707b4b4154907
Signed-off-by: Julius Werner <jwerner@chromium.org>

Add platform-independent coreboot support library ...

This patch adds the foundation for a platform-independent coreboot
support library that can be shared by all platforms that boot BL31 from
coreboot (acting as BL2). It adds code to parse the "coreboot table", a
data structure that coreboot uses to communicate different kinds of
information to later-stage firmware and certain OS drivers.

As a first small use case for this information, allow platforms to
access the serial console configuration used by coreboot, removing the
need to hardcode base address and divisors and allowing Trusted Firmware
to benefit from coreboot's user configuration (e.g. which UART to pick
and which baud rate to use).

Change-Id: I2bfb39cd2609ce6640b844ab68df6c9ae3f28e9e
Signed-off-by: Julius Werner <jwerner@chromium.org>

Merge pull request #1200 from robertovargas-arm/bl2-el3 ...

Add BL2_AT_EL3 build option

lib/cpus: fix branching in reset function for cortex-a72 AARCH32 mode ...

In AARCH32 mode, cortex_a72_reset_func branches to address in lr
register instead of r5 register. This leads to linux boot failure
of Cortex-A72 cores in AARCH32 mode on Juno-R2 board.

This patch fixes the branching of cortex_a72_reset_func to r5
register as in cortex_a57_reset_func implementation.

Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>

bl2-el3: Add BL2_EL3 image ...

This patch enables BL2 to execute at the highest exception level
without any dependancy on TF BL1. This enables platforms which already
have a non-TF Boot ROM to directly load and execute BL2 and subsequent BL
stages without need for BL1.  This is not currently possible because
BL2 executes at S-EL1 and cannot jump straight to EL3.

Change-Id: Ief1efca4598560b1b8c8e61fbe26d1f44e929d69
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

Merge pull request #1218 from antonio-nino-diaz-arm/an/xlat-fix ...

xlat v2: Correctly unmap regions on map error

AMU: Remove unnecessary WARN() ...

If AMU is not supported by the hardware but it is enabled in Trusted
Firmware, the console will be spammed with warnings every time a CPU
is brought up with a CPU ON call.

Remove the warning message as this is more in line with how other
extensions like SPE and SVE are handled.

Change-Id: Iba6d367e4d1375ab554d23d2eaceab3ae1362c5a
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Merge pull request #1197 from dp-arm/dp/amu ...

AMUv1 support

Add hooks to save/restore AMU context for Cortex A75 ...

Change-Id: I504d3f65ca5829bc1f4ebadb764931f8379ee81f
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

AMU: Add hooks to save/restore AMU context ...

On some systems, the AMU counters might reset to 0 when a CPU
powerdown happens.  This behaviour conflicts with the intended
use-case of AMU as lower ELs are only expected to see non-decreasing
counter values.

Change-Id: If25519965d4e6e47e09225d0e732947986cbb5ec
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

AMU: Add configuration helpers for aarch64 ...

Add some AMU helper functions to allow configuring, reading and
writing of the Group 0 and Group 1 counters.  Documentation for these
helpers will come in a separate patch.

Change-Id: I656e070d2dae830c22414f694aa655341d4e2c40
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

AMU: Add plat interface to select which group 1 counters to enable ...

A new platform macro `PLAT_AMU_GROUP1_COUNTERS_MASK` controls which
group 1 counters should be enabled. The maximum number of group 1
counters supported by AMUv1 is 16 so the mask can be at most 0xffff.
If the platform does not define this mask, no group 1 counters are
enabled.

A related platform macro `PLAT_AMU_GROUP1_NR_COUNTERS` is used by
generic code to allocate an array to save and restore the counters on
CPU suspend.

Change-Id: I6d135badf4846292de931a43bb563077f42bb47b
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Add PubSub events for CPU powerdown/powerup ...

The suspend hook is published at the start of a CPU powerdown
operation.  The resume hook is published at the end of a CPU powerup
operation.

Change-Id: I50c05e2dde0d33834095ac41b4fcea4c161bb434
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Use PFR0 to identify need for mitigation of CVE-2017-5915 ...

If the CSV2 field reads as 1 then branch targets trained in one
context cannot affect speculative execution in a different context.
In that case skip the workaround on Cortex A75.

Change-Id: I4d5504cba516a67311fb5f0657b08f72909cbd38
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Workaround for CVE-2017-5715 on Cortex A73 and A75 ...

Invalidate the Branch Target Buffer (BTB) on entry to EL3 by
temporarily dropping into AArch32 Secure-EL1 and executing the
`BPIALL` instruction.

This is achieved by using 3 vector tables.  There is the runtime
vector table which is used to handle exceptions and 2 additional
tables which are required to implement this workaround.  The
additional tables are `vbar0` and `vbar1`.

The sequence of events for handling a single exception is
as follows:

1) Install vector table `vbar0` which saves the CPU context on entry
   to EL3 and sets up the Secure-EL1 context to execute in AArch32 mode
   with the MMU disabled and I$ enabled.  This is the default vector table.

2) Before doing an ERET into Secure-EL1, switch vbar to point to
   another vector table `vbar1`.  This is required to restore EL3 state
   when returning from the workaround, before proceeding with normal EL3
   exception handling.

3) While in Secure-EL1, the `BPIALL` instruction is executed and an
   SMC call back to EL3 is performed.

4) On entry to EL3 from Secure-EL1, the saved context from step 1) is
   restored.  The vbar is switched to point to `vbar0` in preparation to
   handle further exceptions.  Finally a branch to the runtime vector
   table entry is taken to complete the handling of the original
   exception.

This workaround is enabled by default on the affected CPUs.

NOTE
====

There are 4 different stubs in Secure-EL1.  Each stub corresponds to
an exception type such as Sync/IRQ/FIQ/SError.  Each stub will move a
different value in `R0` before doing an SMC call back into EL3.
Without this piece of information it would not be possible to know
what the original exception type was as we cannot use `ESR_EL3` to
distinguish between IRQs and FIQs.

Change-Id: I90b32d14a3735290b48685d43c70c99daaa4b434
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Workaround for CVE-2017-5715 on Cortex A57 and A72 ...

Invalidate the Branch Target Buffer (BTB) on entry to EL3 by disabling
and enabling the MMU.  To achieve this without performing any branch
instruction, a per-cpu vbar is installed which executes the workaround
and then branches off to the corresponding vector entry in the main
vector table.  A side effect of this change is that the main vbar is
configured before any reset handling.  This is to allow the per-cpu
reset function to override the vbar setting.

This workaround is enabled by default on the affected CPUs.

Change-Id: I97788d38463a5840a410e3cea85ed297a1678265
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

xlat v2: Correctly unmap regions on map error ...

`mm_cursor` doesn't have the needed data because the `memmove()` that
is called right before it overwrites that information. In order to get
the information of the region that was being mapped, `mm` has to be used
instead (like it is done to fill the fields of `unmap_mm`).

If the incorrect information is read, this check isn't reliable and
`xlat_tables_unmap_region` may be requested to unmap memory that isn't
mapped at all, triggering assertions.

Change-Id: I602d4ac83095d4e5dac9deb34aa5d00d00e6c289
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Merge pull request #1178 from davidcunado-arm/dc/enable_sve ...

Enable SVE for Non-secure world

Merge pull request #1168 from matt2048/master ...

Replace macro ASM_ASSERTION with macro ENABLE_ASSERTIONS

Enable SVE for Non-secure world ...

This patch adds a new build option, ENABLE_SVE_FOR_NS, which when set
to one EL3 will check to see if the Scalable Vector Extension (SVE) is
implemented when entering and exiting the Non-secure world.

If SVE is implemented, EL3 will do the following:

- Entry to Non-secure world: SIMD, FP and SVE functionality is enabled.

- Exit from Non-secure world: SIMD, FP and SVE functionality is
  disabled. As SIMD and FP registers are part of the SVE Z-registers
  then any use of SIMD / FP functionality would corrupt the SVE
  registers.

The build option default is 1. The SVE functionality is only supported
on AArch64 and so the build option is set to zero when the target
archiecture is AArch32.

This build option is not compatible with the CTX_INCLUDE_FPREGS - an
assert will be raised on platforms where SVE is implemented and both
ENABLE_SVE_FOR_NS and CTX_INCLUDE_FPREGS are set to 1.

Also note this change prevents secure world use of FP&SIMD registers on
SVE-enabled platforms. Existing Secure-EL1 Payloads will not work on
such platforms unless ENABLE_SVE_FOR_NS is set to 0.

Additionally, on the first entry into the Non-secure world the SVE
functionality is enabled and the SVE Z-register length is set to the
maximum size allowed by the architecture. This includes the use case
where EL2 is implemented but not used.

Change-Id: Ie2d733ddaba0b9bef1d7c9765503155188fe7dae
Signed-off-by: David Cunado <david.cunado@arm.com>

AMU: Implement support for aarch32 ...

The `ENABLE_AMU` build option can be used to enable the
architecturally defined AMU counters.  At present, there is no support
for the auxiliary counter group.

Change-Id: Ifc7532ef836f83e629f2a146739ab61e75c4abc8
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

AMU: Implement support for aarch64 ...

The `ENABLE_AMU` build option can be used to enable the
architecturally defined AMU counters.  At present, there is no support
for the auxiliary counter group.

Change-Id: I7ea0c0a00327f463199d1b0a481f01dadb09d312
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Implement support for the Activity Monitor Unit on Cortex A75 ...

The Cortex A75 has 5 AMU counters.  The first three counters are fixed
and the remaining two are programmable.

A new build option is introduced, `ENABLE_AMU`.  When set, the fixed
counters will be enabled for use by lower ELs.  The programmable
counters are currently disabled.

Change-Id: I4bd5208799bb9ed7d2596e8b0bfc87abbbe18740
Signed-off-by: Dimitris Papastamos <dimitris.papastamos@arm.com>

Merge pull request #1145 from etienne-lms/rfc-armv7-2 ...

Support ARMv7 architectures

Merge pull request #1164 from robertovargas-arm/psci-affinity ...

Flush the affinity data in psci_affinity_info

Replace macro ASM_ASSERTION with macro ENABLE_ASSERTIONS ...

This patch replaces the macro ASM_ASSERTION with the macro
ENABLE_ASSERTIONS in ARM Cortex-A53/57/72 MPCore Processor
related files. There is build error when ASM_ASSERTION is set
to 1 and ENABLE_ASSERTIONS is set to 0 because function
asm_assert in common/aarch32/debug.S is defined in the macro
ENABLE_ASSERTIONS but is called with the macro ASM_ASSERTION.

There is also the indication to use ENABLE_ASSERTIONS but not
ASM_ASSERTION in the Makefile.

Signed-off-by: Matt Ma <matt.ma@spreadtrum.com>

Merge pull request #1163 from antonio-nino-diaz-arm/an/parange ...

Add ARMv8.2 ID_AA64MMFR0_EL1.PARange value

Flush the affinity data in psci_affinity_info ...

There is an edge case where the cache maintaince done in
psci_do_cpu_off may not seen by some cores. This case is handled in
psci_cpu_on_start but it hasn't handled in psci_affinity_info.

Change-Id: I4d64f3d1ca9528e364aea8d04e2d254f201e1702
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>