2020-06-25 |
Merge "stm32mp1: use last page of SYSRAM as SCMI shared memory" into integration
Mark Dykes
authored
on 25 Jun 2020
TrustedFirmware Code Review
committed
on 25 Jun 2020
|
2020-06-23 |
stm32mp1: SP_MIN embeds Arm Architecture services
...
Embed Arch Architecture SMCCC services in stm32mp1 SP_MIN. This
service is needed by Linux kernel to setup the SMCCC conduit
used by its SCMI SMC transport driver.
Change-Id: I454a7ef3048a77ab73fff945e8115b60445d5841
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Etienne Carriere
committed
on 23 Jun 2020
|
stm32mp1: use last page of SYSRAM as SCMI shared memory
...
SCMI shared memory is used to exchange message payloads between
secure SCMI services and non-secure SCMI agents. It is mapped
uncached (device) mainly to conform to existing support in
the Linux kernel. Note that executive messages are mostly short
(few 32bit words) hence not using cache will not penalize much
performances.
Platform stm32mp1 shall configure ETZPC to harden properly the
secure and non-secure areas of the SYSRAM address space, that before
CPU accesses the shared memory when mapped non-secure.
This change defines STM32MP_SEC_SYSRAM_BASE/STM32MP_SEC_SYSRAM_SIZE and
STM32MP_NS_SYSRAM_BASE/STM32MP_NS_SYSRAM_SIZE.
Change-Id: I71ff02a359b9668ae1c5a71b5f102cf3d310f289
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Etienne Carriere
committed
on 23 Jun 2020
|
2020-06-03 |
plat/stm32mp1: sp_min relies on etzpc driver
...
Use ETZPC driver to configure secure aware interfaces to assign
them to non-secure world. Sp_min also configures BootROM resources
and SYSRAM to assign both to secure world only.
Define stm32mp15 SoC identifiers for the platform specific DECPROT
instances.
Change-Id: I3bec9f47b04bcba3929e4df886ddb1d5ff843089
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Etienne Carriere
committed
on 3 Jun 2020
|
2020-06-01 |
Merge "drivers: stm32_reset adapt interface to timeout argument" into integration
Mark Dykes
authored
on 1 Jun 2020
TrustedFirmware Code Review
committed
on 1 Jun 2020
|
drivers: stm32_reset adapt interface to timeout argument
...
Changes stm32mp1 reset driver to API to add a timeout argument
to stm32mp_reset_assert() and stm32mp_reset_deassert() and
a return value.
With a supplied timeout, the functions wait the target reset state
is reached before returning. With a timeout of zero, the functions
simply load target reset state in SoC interface and return without
waiting.
Helper functions stm32mp_reset_set() and stm32mp_reset_release()
use a zero timeout and return without a return code.
This change updates few stm32 drivers and plat/stm32mp1 blé_plat_setup.c
accordingly without any functional change.
functional change.
Change-Id: Ia1a73a15125d3055fd8739c125b70bcb9562c27f
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Etienne Carriere
authored
on 8 Dec 2019
Etienne Carriere
committed
on 1 Jun 2020
|
2020-05-11 |
plat/stm32mp1: fdt helpers for secure aware gpio bank
...
New helper functions to get GPIO banks configuration from the FDT.
stm32_get_gpio_bank_pinctrl_node() allows stm32mp platforms to
differentiate specific GPIO banks when these are defined with a specific
path in the FDT.
fdt_get_gpio_bank_pin_count() returns the number of pins in a GPIO bank
as it depends on the SoC variant.
Change-Id: I4481774152b3c6bf35bf986f58e357c2f9c19176
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Etienne Carriere
committed
on 11 May 2020
|
plat/st: move GPIO bank helper function to platform source files
...
Relation between GPIO banks and their base address and offset address
if platform dependent. This change moves helper functions
stm32_get_gpio_bank_base() and stm32_get_gpio_bank_offset() from
plat/st/common to plat/st/stm32mp1/.
Change-Id: Id3d03e585746aa5509c6fab7d88183a92d561e3f
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Etienne Carriere
authored
on 2 Dec 2019
Etienne Carriere
committed
on 11 May 2020
|
2020-05-05 |
plat/stm32: Use generic fdt_get_stdout_node_offset()
...
Now that we have an implementation for getting the node offset of the
stdout-path property in the generic fdt_wrappers code, use that to
replace the current ST platform specific implementation.
Change-Id: I5dd05684e7ca3cb563b5f71c885e1066393e057e
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara
committed
on 5 May 2020
|
plat/stm32: Use generic fdt_get_reg_props_by_name()
...
The STM32 platform port parse DT nodes to find base address to
peripherals. It does this by using its own implementation, even though
this functionality is generic and actually widely useful outside of the
STM32 code.
Re-implement fdt_get_reg_props_by_name() on top of the newly introduced
fdt_get_reg_props_by_index() function, and move it to fdt_wrapper.c.
This is removes the assumption that #address-cells and #size-cells are
always one.
Change-Id: I6d584930262c732b6e0356d98aea50b2654f789d
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara
committed
on 5 May 2020
|
2020-04-29 |
plat/stm32: Implement fdt_read_uint32_default() as a wrapper
...
The STM32 platform code uses its own set of FDT helper functions,
although some of them are fairly generic.
Remove the implementation of fdt_read_uint32_default() and implement it
on top of the newly introduced fdt_read_uint32() function, then convert
all users over.
This also fixes two callers, which were slightly abusing the "default"
semantic.
Change-Id: I570533362b4846e58dd797a92347de3e0e5abb75
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara
committed
on 29 Apr 2020
|
2020-04-28 |
plat/stm32: Use generic fdt_read_uint32_array() implementation
...
The device tree parsing code for the STM32 platform is using its own FDT
helper functions, some of them being rather generic.
In particular the existing fdt_read_uint32_array() implementation is now
almost identical to the new generic code in fdt_wrappers.c, so we can
remove the ST specific version and adjust the existing callers.
Compared to the original ST implementation the new version takes a
pointer to the DTB as the first argument, and also swaps the order of
the number of cells and the pointer.
Change-Id: Id06b0f1ba4db1ad1f733be40e82c34f46638551a
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara
committed
on 28 Apr 2020
|
2020-03-26 |
stm32mp1: use stm32mp_get_ddr_ns_size() function
...
Instead of using dt_get_ddr_size() and withdrawing the secure and shared
memory areas, use stm32mp_get_ddr_ns_size() function.
Change-Id: I5608fd7873589ea0e1262ba7d2ee3e52b53d9a7d
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Yann Gautier
committed
on 26 Mar 2020
|
stm32mp1: set XN attribute for some areas in BL2
...
DTB and BL32 area should not be set as executable in MMU during BL2
execution, hence set those areas as MT_RO_DATA.
Change-Id: I87c47a1e7fda761e541ec98a5b294588384d31db
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Yann Gautier
committed
on 26 Mar 2020
|
stm32mp1: dynamically map DDR later and non-cacheable during its test
...
A speculative accesses to DDR could be done whereas it was not reachable
and could lead to bus stall.
To correct this the dynamic mapping in MMU is used.
A first mapping is done for DDR tests with MT_NON_CACHEABLE attribute,
once DDR access is setup. It is then unmapped and a new mapping DDR is done
with cacheable attribute (through MT_MEMORY) to speed-up BL33 (or OP-TEE)
load.
The disabling of cache during DDR tests is also removed, as now useless.
A call to new functions stm32mp_{,un}map_ddr_non_cacheable() is done
instead.
PLAT_XLAT_TABLES_DYNAMIC is activated globally as used in BL2 and BL32.
BL33 max size is also updated to take into account the secure and shared
memory areas. Those are used in OP-TEE case.
Change-Id: I22c48b4a48255ee264991c34ecbb15bfe87e67c3
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Yann Gautier
committed
on 26 Mar 2020
|
stm32mp1: add a function to get non-secure DDR size
...
This function gets the DDR size from DT, and withdraws (if defined) the
sizes of secure DDR and shared memory areas.
This function also checks DT values fits the default DDR range.
This non-secure memory is available for BL33 and non-secure OS.
Change-Id: I162ae5e990a0f9b6b7d07e539de029f1d61a391b
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Yann Gautier
committed
on 26 Mar 2020
|
2020-03-23 |
plat/st: correctly check pwr-regulators node
...
This warning was issued by cppcheck in our downstream code:
[plat/st/common/stm32mp_dt.c:629] -> [plat/st/common/stm32mp_dt.c:634]:
(warning) Identical condition 'node<0', second condition is always false
The second test has to check variable pwr_regulators_node.
Change-Id: I4a20c4a3ac0ef0639c2df36309d90a61c02b511f
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Yann Gautier
committed
on 23 Mar 2020
|
plat/st: correct static analysis tool warning
...
Correct the following sparse warnings:
plat/st/common/stm32mp_dt.c:103:5: warning:
symbol 'fdt_get_node_parent_address_cells' was not declared.
Should it be static?
plat/st/common/stm32mp_dt.c:123:5: warning:
symbol 'fdt_get_node_parent_size_cells' was not declared.
Should it be static?
As those 2 functions are only used by assert(), put them under
ENABLE_ASSERTIONS flag.
Change-Id: Iad721f12128df83a3de3f53e7920a9c1dce64c56
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Yann Gautier
committed
on 23 Mar 2020
|
2020-03-11 |
Merge changes from topic "stm32mp1-multi-image" into integration
...
* changes:
stm32mp1: platform.mk: support generating multiple images in one build
stm32mp1: platform.mk: migrate to implicit rules
stm32mp1: platform.mk: derive map file name from target name
stm32mp1: platform.mk: generate linker script with fixed name
stm32mp1: platform.mk: use PHONY for the appropriate targets
Sandrine Bailleux
authored
on 11 Mar 2020
TrustedFirmware Code Review
committed
on 11 Mar 2020
|
2020-02-25 |
stm32mp1: platform.mk: support generating multiple images in one build
...
Board Support for the stm32mp1 platform is contained in the device tree,
so if we remove hardcoding of board name from the Makefile, we can build
the intermediary objects once and generate one new tf-a-*.stm32 binary
for every device tree specified. All in one go.
With implicit rules implemented, we only need to change the top level
target to support multi-image builds on the stm32mp1.
Change-Id: I4cae7d32a4c03a3c29c559dc5332e002223902c1
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Ahmad Fatoum
committed
on 25 Feb 2020
|
stm32mp1: platform.mk: migrate to implicit rules
...
Board Support for the stm32mp1 platform is contained in the device tree,
so if we remove hardcoding of board name from the Makefile, we can build
the intermediary objects once and generate one new tf-a-*.stm32 binary
for every device tree specified. All in one go.
Prepare for this by employing implicit rules.
Change-Id: I5a022a89eb12696cd8cee7bf28ac6be54849901f
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Ahmad Fatoum
committed
on 25 Feb 2020
|
stm32mp1: platform.mk: derive map file name from target name
...
Doing this allows us in the next commit to use implicit rules (%-patterns)
to cover all the images we generate during a stm32mp1 build.
Change-Id: Ibde59d10ccce42566f82820117d7fd0d77345e6c
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Ahmad Fatoum
committed
on 25 Feb 2020
|
stm32mp1: platform.mk: generate linker script with fixed name
...
The linker script has no board-specific information that necessitates it
having a name derived from the board name. Give it a fixed name, so we
can later reuse the same linker script for multiple boards.
Change-Id: Ie6650f00389f4ab8577ae82a36c620af9c64101e
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Ahmad Fatoum
committed
on 25 Feb 2020
|
stm32mp1: platform.mk: use PHONY for the appropriate targets
...
Currently, building TF-A for STM32MP1 triggers a full rebuild,
avoid this by removing the .PHONY: specification for the final image and
replace it by specifying PHONYness for the targets that don't actually
produce file output.
This will come in handy in follow-up commits, when implicit rules are
introduced, as implicit rule search is skipped for .PHONY targets.
Change-Id: Ib9966479032b081a54123b99f889760e85639f19
Fixes: f74cbc93a ("stm32mp1: Link BL2, BL32 and DTB in one binary")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Ahmad Fatoum
committed
on 25 Feb 2020
|
stm32: Use generic console_t data structure
...
Since now the generic console_t structure holds the UART base address as
well, let's use that generic location and drop the UART driver specific
data structure at all.
Change-Id: Iea6ca26ff4903c33f0fad27fec96fdbabd4e0a91
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Andre Przywara
committed
on 25 Feb 2020
|
2020-01-28 |
Enable -Wredundant-decls warning check
...
This flag warns if anything is declared more than once in the same
scope, even in cases where multiple declaration is valid and changes
nothing.
Consequently, this patch also fixes the issues reported by this
flag. Consider the following two lines of code from two different source
files(bl_common.h and bl31_plat_setup.c):
IMPORT_SYM(uintptr_t, __RO_START__, BL_CODE_BASE);
IMPORT_SYM(unsigned long, __RO_START__, BL2_RO_BASE);
The IMPORT_SYM macro which actually imports a linker symbol as a C expression.
The macro defines the __RO_START__ as an extern variable twice, one for each
instance. __RO_START__ symbol is defined by the linker script to mark the start
of the Read-Only area of the memory map.
Essentially, the platform code redefines the linker symbol with a different
(relevant) name rather than using the standard symbol. A simple solution to
fix this issue in the platform code for redundant declarations warning is
to remove the second IMPORT_SYM and replace it with following assignment
static const unsigned long BL2_RO_BASE = BL_CODE_BASE;
Change-Id: If4835d1ee462d52b75e5afd2a59b64828707c5aa
Signed-off-by: Madhukar Pappireddy <madhukar.pappireddy@arm.com>
Madhukar Pappireddy
committed
on 28 Jan 2020
|
2020-01-24 |
st: Unify Platform specific defines for PSCI module
...
PLATFORM_CORE_COUNT - Unsigned int
PLATFORM_CLUSTER_COUNT - Unsigned int
PLATFORM_MAX_CPUS_PER_CLUSTER - Unsigned int
PLATFORM_CORE_COUNT_PER_CLUSTER - Unsigned int
Signed-off-by: Deepika Bhavnani <deepika.bhavnani@arm.com>
Change-Id: I3421336230981d4cda301fa2cef24b94b08353b1
Deepika Bhavnani
authored
on 13 Dec 2019
Soby Mathew
committed
on 24 Jan 2020
|
2020-01-20 |
stm32mp1: Add support for SPI-NOR boot device
...
STM32MP1 platform is able to boot from SPI-NOR devices.
These modifications add this support using the new
SPI-NOR framework.
Change-Id: I75ff9eba4661f9fb87ce24ced2bacbf8558ebe44
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Lionel Debieve
committed
on 20 Jan 2020
|
stm32mp1: Add support for SPI-NAND boot device
...
STM32MP1 platform is able to boot from SPI-NAND devices.
These modifications add this support using the new
SPI-NAND framework.
Change-Id: I0d5448bdc4bde153c1209e8043846c0f935ae5ba
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Lionel Debieve
committed
on 20 Jan 2020
|
stm32mp1: Add support for raw NAND boot device
...
STM32MP1 platform is able to boot from raw NAND devices.
These modifications add this support using the new
raw NAND framework.
Change-Id: I9e9c2b03930f98a5ac23f2b6b41945bef43e5043
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Lionel Debieve
committed
on 20 Jan 2020
|