tools: Move doimage to marvell folder for future add-ons ...

Move doimage utility from toos/doimage to tools/marvell/doimage.
This is done for supporting mode Marvell tools in the future.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

mvebu: cp110: introduce COMPHY porting layer ...

Some of COMPHY parameters depends on the hw connection between the SoC
and the PHY, which can vary on different boards e.g. due to different
wires length. Define the "porting layer" with some defaults
parameters. It ease updating static values which needs to be updated due
to board differences, which are now grouped in one place.

Example porting layer for a8k-db is under:
plat/marvell/a8k/a80x0/board/phy-porting-layer.h

If for some boards parameters are not defined (missing
phy-porting-layer.h), the default values are used
(drivers/marvell/comphy/phy-default-porting-layer.h)
and the following compilation warning is show:
"Using default comphy params - you may need to suit them to your board".

The common COMPHY driver code is extracted in order to be shared with
future COMPHY driver for A3700 SoC platforms

Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>

Merge pull request #1582 from ldts/rcar_gen3/upstream ...

rcar_gen3: initial support

Merge pull request #1553 from glneo/dcache-late-disable ...

Allow D-Cache to remain on during core power-down

Merge pull request #1629 from robertovargas-arm/hw-assisted-coherency-lock ...

Optimize bakery locks when HW_ASSISTED_COHERENCY is enabled

Merge pull request #1631 from deepan02/deepak-arm/relocate-jump_if_cpu_midr ...

plat/arm: relocate the jump_if_cpu_midr macro.

Merge pull request #1628 from antonio-nino-diaz-arm/an/sharing ...

plat/arm: Small reorganization of platform code

rcar_gen3: drivers: staging ...

- ddr
 - pfc [pin function controller]
 - qos [bandwidth]

checkpatch.pl is generating too many errors.

rcar-gen3: initial commit for the rcar-gen3 boards ...

Reference code:
==============

rar_gen3: IPL and Secure Monitor Rev1.0.22
https://github.com/renesas-rcar/arm-trusted-firmware [rcar_gen3]

Author: Takuya Sakata <takuya.sakata.wz@bp.renesas.com>
Date:   Thu Aug 30 21:26:41 2018 +0900
	Update IPL and Secure Monitor Rev1.0.22

General Information:
===================

This port has been tested on the Salvator-X Soc_id r8a7795 revision
ES1.1 (uses an SPD).

Build Tested:
-------------
ATFW_OPT="LSI=H3 RCAR_DRAM_SPLIT=1 RCAR_LOSSY_ENABLE=1"
MBEDTLS_DIR=$mbedtls

$ make clean bl2 bl31 rcar PLAT=rcar ${ATFW_OPT} SPD=opteed

Other dependencies:
------------------
* mbed_tls:
  git@github.com:ARMmbed/mbedtls.git [devel]

  Merge: 68dbc94 f34a4c1
  Author: Simon Butcher <simon.butcher@arm.com>
  Date:   Thu Aug 30 00:57:28 2018 +0100

* optee_os:
  https://github.com/BayLibre/optee_os

  Until it gets merged into OP-TEE, the port requires Renesas' Trusted
  Environment with a modification to support power management.

  Author: Jorge Ramirez-Ortiz <jramirez@baylibre.com>
  Date:   Thu Aug 30 16:49:49 2018 +0200
    plat-rcar: cpu-suspend: handle the power level
    Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com>

* u-boot:
  The port has beent tested using mainline uboot.

  Author: Fabio Estevam <festevam@gmail.com>
  Date:   Tue Sep 4 10:23:12 2018 -0300

*linux:
  The port has beent tested using mainline kernel.

  Author: Linus Torvalds <torvalds@linux-foundation.org>
  Date:   Sun Sep 16 11:52:37 2018 -0700
      Linux 4.19-rc4

Overview
---------

BOOTROM starts the cpu at EL3; In this port BL2 will therefore be entered
at this exception level (the Renesas' ATF reference tree [1] resets into
EL1 before entering BL2 - see its bl2.ld.S)

BL2 initializes DDR (and i2c to talk to the PMIC on some platforms)
before determining the boot reason (cold or warm).

During suspend all CPUs are switched off and the DDR is put in
backup mode (some kind of self-refresh mode). This means that BL2 is
always entered in a cold boot scenario.

Once BL2 boots, it determines the boot reason, writes it to shared
memory (BOOT_KIND_BASE) together with the BL31 parameters
(PARAMS_BASE) and jumps to BL31.

To all effects, BL31 is as if it is being entered in reset mode since
it still needs to initialize the rest of the cores; this is the reason
behind using direct shared memory access to  BOOT_KIND_BASE and
PARAMS_BASE instead of using registers to get to those locations (see
el3_common_macros.S and bl31_entrypoint.S for the RESET_TO_BL31 use
case).

Depending on the boot reason BL31 initializes the rest of the cores:
in case of suspend, it uses a MBOX memory region to recover the
program counters.

[1] https://github.com/renesas-rcar/arm-trusted-firmware
Tests
-----

* cpuidle
  -------
   enable kernel's cpuidle arm_idle driver and boot

* system suspend
  --------------
  $ cat suspend.sh
    #!/bin/bash
    i2cset -f -y 7 0x30 0x20 0x0F
    read -p "Switch off SW23 and press return " foo
    echo mem > /sys/power/state

* cpu hotplug:
  ------------
  $ cat offline.sh
    #!/bin/bash
    nbr=$1
    echo 0 > /sys/devices/system/cpu/cpu$nbr/online
    printf "ONLINE:  " && cat /sys/devices/system/cpu/online
    printf "OFFLINE: " && cat /sys/devices/system/cpu/offline

  $ cat online.sh
    #!/bin/bash
    nbr=$1
    echo 1 > /sys/devices/system/cpu/cpu$nbr/online
    printf "ONLINE:  " && cat /sys/devices/system/cpu/online
    printf "OFFLINE: " && cat /sys/devices/system/cpu/offline

Signed-off-by: ldts <jramirez@baylibre.com>

ti: k3: common: Do not disable cache on TI K3 core powerdown ...

Leave the caches on and explicitly flush any data that
may be stale when the core is powered down. This prevents
non-coherent interconnect access which has negative side-
effects on AM65x.

Signed-off-by: Andrew F. Davis <afd@ti.com>

scmi: Optimize bakery locks when HW_ASSISTED_COHERENCY is enabled ...

When HW_ASSISTED_COHERENCY is enabled we can use spinlocks
instead of using the more complex and slower bakery algorithm.

Change-Id: I9d791a70050d599241169b9160a67e57d5506564
Signed-off-by: Roberto Vargas <roberto.vargas@arm.com>

plat/arm: relocate the jump_if_cpu_midr macro. ...

macro jump_if_cpu_midr is used commonly by many arm platform.
It has now been relocated to common place to remove duplication
of code.

Change-Id: Ic0876097dbc085df4f90eadb4b7687dde7c726da
Signed-off-by: Deepak Pandey <Deepak.Pandey@arm.com>

Merge pull request #1606 from satheesbalya-arm/sb1_2603_misra_plat ...

plat/arm: Fix misra warnings in platform code

plat/arm: Fix misra warnings in platform code ...

Change-Id: Ica944acc474a099219d50b041cfaeabd4f3d362f
Signed-off-by: Sathees Balya <sathees.balya@arm.com>

plat/arm: Remove file arm_board_def.h ...

This file is shared between FVP and all CSS platforms. While it may be
true that some definitions can be common, it doesn't make sense
conceptually. For example, the stack size depends on the platform and so
does the SRAM size.

After removing them, there are not enough common definitions to justify
having this header, so the other definitions have been moved to the
platform_def.h of FVP, board_css_def.h and arm_def.h.

Change-Id: Ifbf4b017227f9dfefa1a430f67d7d6baae6a4ba1
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Merge pull request #1621 from jts-arm/typos ...

Various corrections of typos

Merge pull request #1619 from antonio-nino-diaz-arm/an/norflash ...

plat/arm: Move norflash driver to drivers/ folder

plat/arm: Move board_css_common.c to juno folder ...

This file is only used by Juno as all other CSS platforms have their own
private memory maps.

Change-Id: I1c9f27aac7b1d8bff4d92674e8bde5505b93c8c4
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Merge pull request #1620 from deepan02/deepak-arm/move-reset-to-bl31 ...

plat/arm: allow RESET_TO_BL31 for CSS-based platforms

Merge pull request #1614 from MISL-EBU-System-SW/integration-fix ...

Fix service CPU image load at BL2 stage and update maintainers list

Merge pull request #1607 from girishpathak/gp/346_sgm775_earlylog_fix_v2 ...

plat/arm/css/sgm: Reorder early platform init

Replace S-EL3 references by EL3 ...

The "Secure" prefix (S-ELx) is valid only for S-EL0 and S-EL1 but is
meaningless for EL3, since EL3 is always secure. Hence, the "S" prefix
has been removed from wherever it was used as "S-EL3".

Change-Id: Icdeac9506d763f9f83d7297c7113aec7b85e9dbe
Signed-off-by: John Tsichritzis <john.tsichritzis@arm.com>

plat/arm/css/sgm: Reorder early platform init ...

In the function, bl1_early_platform_setup in the file
plat/arm/css/sgm/sgm_bl1_setup.c:

  plat_config_init();

  arm_bl1_early_platform_setup();

The debug messages logged by plat_config_init() are lost because
the console is initialized in the function
arm_bl1_early_platform_setup()

To see the logs of plat_config_init, this fix re-orders above calls
so that the console is initialized before call to plat_config_init.

Change-Id: I2e98f1f67c591cca24e28905acd0838ea3697a7c
Signed-off-by: Girish Pathak <girish.pathak@arm.com>

plat/arm: Move norflash driver to drivers/ folder ...

This way it can be reused by other platforms if needed.

Note that this driver is designed to work with the Versatile Express NOR
flash of Juno and FVP. In said platforms, the memory is organized as an
interleaved memory of two chips with a 16 bit word.

Any platform that wishes to reuse it with a different configuration will
need to modify the driver so that it is more generic.

Change-Id: Ic721758425864e0cf42b7b9b04bf0d9513b6022e
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

plat/arm: allow RESET_TO_BL31 for CSS-based platforms ...

This lets any future CSS platforms to use RESET_TO_BL31 flag.

Change-Id: I32a90fce43cb0c6f4d33589653a0fd6a7ecc9577
Signed-off-by: Deepak Pandey <Deepak.Pandey@arm.com>

Fix misra warnings in SMC and power mgmt code ...

Change-Id: Ia00eba2b18804e6498d935d33ec104953e0e5e03
Signed-off-by: Sathees Balya <sathees.balya@arm.com>

plat: marvell: invoke platform specific scp_bl2 image handler ...

Before switching to new API the scp_bl2 handler was invoked from
bl2/bl2_image_load.c which was removed. Invoke the platform specific
scp_bl2 handler in analogy to ARM and HiSilicon.

Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>

Merge pull request #1583 from danielboulby-arm/db/AArch32_Multi_Console ...

Enable Multi Console API in AArch32

Merge pull request #1609 from MISL-EBU-System-SW/integration-ble ...

plat/marvell: Move BLE into the platform tree, minor fix in tools.

Merge pull request #1603 from antonio-nino-diaz-arm/db/reclaim-init ...

Reclaim BL31 initialization code memory for runtime data