This fixes an off by 576x bug the the sram_udelay code. The wrong
value was multipled by the system ticks per mhz value (which is 24),
so we delayed for 1/576th of the requested time.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>

Ensure (where possible) that switch statements in plat comply with MISRA
rules 16.1 - 16.7.

Change-Id: Ie4a7d2fd10f6141c0cfb89317ea28a755391622f
Signed-off-by: Jonathan Wright <jonathan.wright@arm.com>

we will use timer in pmusarm, when logic power rail shutdown,
the secure timer will gone, so need to initial it in pmusram.

Change-Id: I472e7eec3fc197f56223e6fff9167556c1c5e3bc
Signed-off-by: Lin Huang <hl@rock-chips.com>

we do not have enough pmusram space now, so use slice1 to restore
ddr slice1 ~ slice4, that's will save more pmusram space.

Change-Id: Id54a7944f33d01a8f244cee6a8a0707bfe4d42da
Signed-off-by: Lin Huang <hl@rock-chips.com>

when logic power rail shutdown, CRU register will back to reset
value, ddr use abpll as clock source when do suspend, we need to save
and dpll value in pmusram, then set back these ddr clock back to dpll
when dddr resume.

Change-Id: I95dc0173649e8515859cfa46b40a606e0cc2fe3f
Signed-off-by: Lin Huang <hl@rock-chips.com>

This fix modifies the order of system includes to meet the ARM TF coding
standard. There are some exceptions to this change in order to retain
header groupings and where there are headers within #if statements.

Change-Id: Ib5b668c992d817cc860e97b29e16ef106d17e404
Signed-off-by: Isla Mitchell <isla.mitchell@arm.com>

This moves the DRAM restore code to PMUSRAM. This is so that the
voltage domain that contains the SRAM that it was stored in before may
be turned off during system suspend.

Change-Id: Id761181a30caadd12f1ce061d1034f3159a76d28
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This converts two functions to use for-loops. This saves a bit of
space to help moving DRAM resume code to PMUSRAM.

Change-Id: Ie6ca490cf50c2ec83335cf1845b337c3e8a47496
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

The removed if statement would make the same check that the for loop
it is in does to break out of the for loop, so it doesn't make any
sense to keep it there.

Change-Id: I819c29f9182e6de1fc47e418aed15ad38e8f9fa9
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This removes the mmio_... function calls to set the multicast bit for
the PHY registers when overriding the write leveling values. These are
not needed since multicast is set by default when calling the
function, and it's also better not to leave the side effect of
disabling multicast when exiting the function.

Change-Id: I83e089a2a2d55268b3832f36724c3b2c4be81082
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This removes the phy_dll_bypass_set function as it is unneeded. The
values that function sets are saved during suspend, so the proper
values will be restored on resume.

Change-Id: I17542206c56e639ce8cb6375233145167441d4e2
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This removes the space allocation for the unused PHY register space.
For instance in PHY registers 0-127, only 0-90 are used, so don't save
the 91-127 registers. This saves about 1.6KB of space.

Change-Id: I0c9f6d9bed8f0c1f3b8b805dfb10cf0c06208919
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

The differential signal of DQS need keep low level
before gate training. It need enable RPULL and disable
PHY side ODT to ensure it when do gate training.
But it can not access the PHY registers to do it when
perform DFS.So the workaroud as below: It is ensure that
the PHY's read gate is landing somewhere in the incoming
DQS's pulses before it starts searching for pre-amble window.
It need get the rddqs_delay_ps to calculate the start point
of gate training for DFS.

Change-Id: I79eabcf4ec9a9c8f4539f68a51f22afba49c72fe
Signed-off-by: Lin Huang <hl@rock-chips.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/

Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

The printf() isn't used by the firmware itself, just by the tools under
the ./tools/ folder. Then tf_printf will unconditionally print.
Remove the unused print_dram_status_info() function.

Change-Id: Ie699ccb54a5be9a2cbbd7b8d4193b57075a2f57a
Signed-off-by: Caesar Wang <wxt@rock-chips.com>

RK3399 ARM TF clean up 20170210

This fixes code that set a tFC value in a register using the tRFC
value instead.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>

The F1 CAS latency setting was not bit shifted, which resulted in
setting the DRAM additive latency value instead.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>

On resume, we use the DFS hardware to switch frequency index,
followed by a full training sequence on that index. Leaving
the DFS training modules enabled causes issues with the full
training done at resume. We also only needs these enabled
during a call to ddr_set_rate during runtime, so there's no
issue disabling them at the end of ddr_set_rate.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

This moves the setting of the DQS drive strength to the M0 to minimize
the impact on DDR transactions. We need to have the DQS drive strength
changed for data training, which is triggered by the M0, but it also
needs to be changed back when data training is finished.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This removes an optimization to not recalculate parameters if the
frequency index being switched to hold the next frequency. This is
because some registers do not have a copy per frequency index, so this
optimization might be causing problems.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>

We were getting far off values on resume for the RX_CAL_DQS values.
This saves and restores the values for suspend/resume until the root
of the problem is figured out

Signed-off-by: Derek Basehore <dbasehore@chromium.org>

The goal is that make clear the secure and SoC codes. Now cleaning them
will help secure code extensions for RK3399 in the future.

Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

So far, there are more and more features are supported on the RK3399,
meanwhile, these features are increasingly being defined and intertwined.
It's time to clean up and make them clearer.

Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

This patch do following things:
1. Request hresetn_cm0s_pmu_req first then request
   poresetn_cm0s_pmu_req during M0 enable.
2. Do not diable M0 clock for ddr dvfs.
3. Correct the clk_pmum0_gating_dis bit, it is BIT0 not BIT1
4. do not set/clear hclk_noc_pmu_en in M0 code, it does not relate
   to the M0 clock.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

The phy pll needs to get 2X frequency to the DDR, so set the
pll_postdiv to 0.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Derek Basehore <dbasehore@chromium.org>

For ddr dfs stable, We need to enable ddr CA training
when do ddr dfs.

Signed-off-by: Lin Huang <hl@rock-chips.com>

This enables per CS training at 666MHz and above for ddrfreq per
vendor recommendation. Since the threshold was used for latency was
the same value, this also adds a new value for that.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>

This patch sets the frequency configuration of the next DRAM DFS index
to the configuration of the current index. This does not perform a
frequency transition. It just configures registers so the training on
resume for both indices will be correct.

Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>

We used dcf do ddr frequency scaling, but we just include a dcf
binary, it hard to maintain later, we have M0 compile flow in ATF,
and M0 can also work for ddr frequency scaling, so let's use it.

Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>