This resolves MISRA defects such as:

    plat/common/plat_bl1_common.c:63:[MISRA C-2012 Rule 14.4 (required)]
    The condition expression "1" does not have an essentially boolean type.

Change-Id: I679411980ad661191fbc834a44a5eca5494fd0e2
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>

Change the return type of "arm_io_is_toc_valid()" and
"plat_arm_bl1_fwu_needed()" to bool, to match function behavior.

Change-Id: I503fba211219a241cb263149ef36ca14e3362a1c
Signed-off-by: Louis Mayencourt <louis.mayencourt@arm.com>

The watchdog is configured with a default value of 256 seconds in order
to implement the Trusted Board Boot Requirements.

For the FVP and Juno platforms, the FWU process relies on a watchdog
reset. In order to automate the test of FWU, the length of this process
needs to be as short as possible. Instead of waiting for those 4 minutes
to have a reset by the watchdog, tell it to reset immediately.

There are no side effects as the value of the watchdog's load register
resets to 0xFFFFFFFF.

Tested on Juno.

Change-Id: Ib1aea80ceddc18ff1e0813a5b98dd141ba8a3ff2
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>

The BL1 stage setup code for ARM platforms sets up the SP805 watchdog
controller as the secure watchdog. But not all ARM platforms use SP805
as the secure watchdog controller.

So introduce two new ARM platform code specific wrapper functions to
start and stop the secure watchdog. These functions then replace the
calls to SP805 driver in common BL1 setup code. All the ARM platforms
implement these wrapper functions by either calling into SP805 driver
or the SBSA watchdog driver.

Change-Id: I1a9a11b124cf3fac2a84f22ca40acd440a441257
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>

Improved support for W=2 compilation flag by solving some nested-extern
and sign-compare warnings.

The libraries are compiling with warnings (which turn into errors with
the Werror flag).

Outside of libraries, some warnings cannot be fixed.

Change-Id: I06b1923857f2a6a50e93d62d0274915b268cef05
Signed-off-by: Ambroise Vincent <ambroise.vincent@arm.com>

Change-Id: Ia601d5ad65ab199e747fb60af4979b7db477d249
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Use full include paths like it is done for common includes.

This cleanup was started in commit d40e0e08283a ("Sanitise includes
across codebase"), but it only cleaned common files and drivers. This
patch does the same to Arm platforms.

Change-Id: If982e6450bbe84dceb56d464e282bcf5d6d9ab9b
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

From now on, platform_def.h must include any header with definitions that
are platform-specific (like arm_def.h) and the included headers mustn't
include back platform_def.h, and shouldn't be used by other files. Only
platform_def.h should be included in other files. This will ensure that all
needed definitions are present, rather than needing to include all the
headers in all the definitions' headers just in case.

This also prevents problems like cyclic dependencies.

Change-Id: I9d3cf4d1de4b956fa035c79545222697acdaf5ca
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

Enforce full include path for includes. Deprecate old paths.

The following folders inside include/lib have been left unchanged:

- include/lib/cpus/${ARCH}
- include/lib/el3_runtime/${ARCH}

The reason for this change is that having a global namespace for
includes isn't a good idea. It defeats one of the advantages of having
folders and it introduces problems that are sometimes subtle (because
you may not know the header you are actually including if there are two
of them).

For example, this patch had to be created because two headers were
called the same way: e0ea0928d5b7 ("Fix gpio includes of mt8173 platform
to avoid collision."). More recently, this patch has had similar
problems: 46f9b2c3a282 ("drivers: add tzc380 support").

This problem was introduced in commit 4ecca33988b9 ("Move include and
source files to logical locations"). At that time, there weren't too
many headers so it wasn't a real issue. However, time has shown that
this creates problems.

Platforms that want to preserve the way they include headers may add the
removed paths to PLAT_INCLUDES, but this is discouraged.

Change-Id: I39dc53ed98f9e297a5966e723d1936d6ccf2fc8f
Signed-off-by: Antonio Nino Diaz <antonio.ninodiaz@arm.com>

The patch 7b56928 unified the FWU mechanism on FVP and Juno
platforms due to issues with MCC firmware not preserving the
NVFLAGS. With MCCv150 firmware, this issue is resolved. Also
writing to the NOR flash while executing from the same flash
in Bypass mode had some stability issues. Hence, since the
MCC firmware issue is resolved, this patch reverts to the
NVFLAGS mechanism to detect FWU. Also, with the introduction
of SDS (Shared Data Structure) by the SCP, the reset syndrome
needs to queried from the appropriate SDS field.

Change-Id: If9c08f1afaaa4fcf197f3186887068103855f554
Signed-off-by: Sathees Balya <sathees.balya@arm.com>
Signed-off-by: Soby Mathew <Soby.Mathew@arm.com>

Previously, Juno used to depend on the SSC_GPRETN register to inform
about the reset syndrome. This method was removed when SCP migrated
to the SDS framework. But even the SDS framework doesn't report the
reset syndrome correctly and hence Juno failed to enter Firmware
update mode if BL2 authentication failed.

In addition to that, the error code populated in V2M_SYS_NVFLAGS register
does not seem to be retained any more on Juno across resets. This could
be down to the motherboard firmware not doing the necessary to preserve
the value.

Hence this patch modifies the Juno platform to use the same mechanism to
trigger firmware update as FVP which is to corrupt the FIP TOC on
authentication failure. The implementation in `fvp_err.c` is made common
for ARM platforms and is moved to the new `arm_err.c` file in
plat/arm/common folder. The BL1 and BL2 mmap table entries for Juno
are modified to allow write to the Flash memory address.

Change-Id: Ica7d49a3e8a46a90efd4cf340f19fda3b549e945
Signed-off-by: Soby Mathew <soby.mathew@arm.com>

This fix modifies the order of #includes in ARM standard platforms
to meet the ARM TF coding standard.

Change-Id: Ide19aad6233babda4eea2d17d49e523645fed1b2
Signed-off-by: Isla Mitchell <isla.mitchell@arm.com>

To make software license auditing simpler, use SPDX[0] license
identifiers instead of duplicating the license text in every file.

NOTE: Files that have been imported by FreeBSD have not been modified.

[0]: https://spdx.org/

Change-Id: I80a00e1f641b8cc075ca5a95b10607ed9ed8761a
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

Following steps are required to boot JUNO in AArch32 state:
1> BL1, in AArch64 state, loads BL2.
2> BL2, in AArch64 state, initializes DDR.
  Loads SP_MIN & BL33 (AArch32 executable)images.
  Calls RUN_IMAGE SMC to go back to BL1.
3> BL1 writes AArch32 executable opcodes, to load and branch
  at the entrypoint address of SP_MIN, at HI-VECTOR address and
  then request for warm reset in AArch32 state using RMR_EL3.

This patch makes following changes to facilitate above steps:
* Added assembly function to carry out step 3 above.
* Added region in TZC that enables Secure access to the
  HI-VECTOR(0xFFFF0000) address space.
* AArch32 image descriptor is used, in BL2, to load
  SP_MIN and BL33 AArch32 executable images.

A new flag `JUNO_AARCH32_EL3_RUNTIME` is introduced that
controls above changes. By default this flag is disabled.

NOTE: BL1 and BL2 are not supported in AArch32 state for JUNO.

Change-Id: I091d56a0e6d36663e6d9d2bb53c92c672195d1ec
Signed-off-by: Yatharth Kochar <yatharth.kochar@arm.com>
Signed-off-by: dp-arm <dimitris.papastamos@arm.com>

The current FWU_SMC_UPDATE_DONE implementation incorrectly passes
an unused framework cookie through to the 1st argument in the
platform function `bl1_plat_fwu_done`. The intent is to allow
the SMC caller to pass a cookie through to this function.

This patch fixes FWU_SMC_UPDATE_DONE to pass x1 from the caller
through to `bl1_plat_fwu_done`. The argument names are updated
for clarity.

Upstream platforms currently do not use this argument so no
impact is expected.

Change-Id: I107f4b51eb03e7394f66d9a534ffab1cbc09a9b2

This patch adds Firmware Update support for ARM platforms.

New files arm_bl1_fwu.c and juno_bl1_setup.c were added to provide
platform specific Firmware update code.

BL1 now includes mmap entry for `ARM_MAP_NS_DRAM1` to map DRAM for
authenticating NS_BL2U image(For both FVP and JUNO platform).

Change-Id: Ie116cd83f5dc00aa53d904c2f1beb23d58926555