/*
 * i2c.h - definitions for the barebox i2c framework
 *
 * Copyright (C) 2009 by Marc Kleine-Budde <mkl@pengutronix.de>
 *
 * This file is released under the GPLv2
 *
 * Derived from:
 * - i2c.h - i.MX I2C driver header file
 *   Copyright (c) 2008, Darius Augulis <augulis.darius@gmail.com>
 * - i2c.h - definitions for the i2c-bus interface
 *   Copyright (C) 1995-2000 Simon G. Vogl
 *
 */

#ifndef I2C_I2C_H
#define I2C_I2C_H

#include <driver.h>
#include <init.h>
#include <linux/types.h>

struct i2c_adapter;

/*
 * struct i2c_platform_data - structure of platform data for MXC I2C driver
 * @param	bitrate	Bus speed measured in Hz
 *
 */
struct i2c_platform_data {
	int bitrate;
};

/* I2C Frequency Modes */
#define I2C_MAX_STANDARD_MODE_FREQ	100000
#define I2C_MAX_FAST_MODE_FREQ		400000
#define I2C_MAX_FAST_MODE_PLUS_FREQ	1000000
#define I2C_MAX_TURBO_MODE_FREQ		1400000
#define I2C_MAX_HIGH_SPEED_MODE_FREQ	3400000
#define I2C_MAX_ULTRA_FAST_MODE_FREQ	5000000

#define I2C_NAME_SIZE	20

#define I2C_M_RD		0x0001	/* read data, from slave to master */
#define I2C_M_DATA_ONLY		0x0002	/* transfer data bytes only */
#define I2C_M_TEN               0x0010  /* this is a ten bit chip address */
#define I2C_M_IGNORE_NAK        0x1000  /* if I2C_FUNC_PROTOCOL_MANGLING */
#define I2C_M_STOP		0x8000	/* if I2C_FUNC_PROTOCOL_MANGLING */

/**
 * struct i2c_msg - an I2C transaction segment beginning with START
 *
 * An i2c_msg is the low level representation of one segment of an I2C
 * transaction. It is visible to drivers in the @i2c_transfer()
 * procedure and to I2C adapter drivers through the
 * @i2c_adapter.@master_xfer() method.
 *
 * All I2C adapters implement the standard rules for I2C transactions.
 * Each transaction begins with a START. That is followed by the
 * slave address, and a bit encoding read versus write. Then follow
 * all the data bytes, The transfer terminates with a NAK, or when all
 * those bytes have been transferred and ACKed. If this is the last
 * message in a group, it is followed by a STOP. Otherwise it is
 * followed by the next @i2c_msg transaction segment, beginning with a
 * (repeated) START.
 *
 */
struct i2c_msg {
	__u8			*buf;	/**< The buffer into which data is read, or from which it's written. */
	__u16			addr;	/**< Slave address, seven bits */
	__u16			flags;	/**< I2C_M_RD is handled by all adapters */
	__u16			len;	/**< Number of data bytes in @buf being read from or written to the I2C slave address. */
};

/**
 * struct i2c_bus_recovery_info - I2C bus recovery information
 * @recover_bus: Recover routine. Either pass driver's recover_bus() routine, or
 *	i2c_generic_scl_recovery() or i2c_generic_gpio_recovery().
 * @get_scl: This gets current value of SCL line. Mandatory for generic SCL
 *	recovery. Used internally for generic GPIO recovery.
 * @set_scl: This sets/clears SCL line. Mandatory for generic SCL recovery. Used
 *	internally for generic GPIO recovery.
 * @get_sda: This gets current value of SDA line. Optional for generic SCL
 *	recovery. Used internally, if sda_gpio is a valid GPIO, for generic GPIO
 *	recovery.
 * @prepare_recovery: This will be called before starting recovery. Platform may
 *	configure padmux here for SDA/SCL line or something else they want.
 * @unprepare_recovery: This will be called after completing recovery. Platform
 *	may configure padmux here for SDA/SCL line or something else they want.
 * @scl_gpio: gpio number of the SCL line. Only required for GPIO recovery.
 * @sda_gpio: gpio number of the SDA line. Only required for GPIO recovery.
 */
struct i2c_bus_recovery_info {
	int (*recover_bus)(struct i2c_adapter *);

	int (*get_scl)(struct i2c_adapter *);
	void (*set_scl)(struct i2c_adapter *, int val);
	int (*get_sda)(struct i2c_adapter *);

	void (*prepare_recovery)(struct i2c_adapter *);
	void (*unprepare_recovery)(struct i2c_adapter *);

	/* gpio recovery */
	int scl_gpio;
	int sda_gpio;
};

int i2c_recover_bus(struct i2c_adapter *adap);

/* Generic recovery routines */
int i2c_get_scl_gpio_value(struct i2c_adapter *adap);
void i2c_set_scl_gpio_value(struct i2c_adapter *adap, int val);
int i2c_get_sda_gpio_value(struct i2c_adapter *adap);
int i2c_generic_gpio_recovery(struct i2c_adapter *adap);
int i2c_generic_scl_recovery(struct i2c_adapter *adap);

/**
 * i2c_adapter is the structure used to identify a physical i2c bus
 * along with the access algorithms necessary to access it.
 *
 */
struct i2c_adapter {
	struct device_d		dev;	/* ptr to device */
	int			nr;	/* bus number */
	int (*master_xfer)(struct i2c_adapter *adap, struct i2c_msg *msgs, int num);
	struct list_head	list;
	int			retries;
	void 			*algo_data;

	struct i2c_bus_recovery_info *bus_recovery_info;
};

#define to_i2c_adapter(d) container_of(d, struct i2c_adapter, dev)

struct i2c_client {
	struct device_d		dev;
	struct i2c_adapter	*adapter;
	unsigned short		addr;
	void			*driver_data;	/* Driver data, set and get with
							dev_set/get_drvdata */
};

#define to_i2c_client(a)	container_of(a, struct i2c_client, dev)

static inline void *i2c_get_clientdata(const struct i2c_client *dev)
{
	return dev->driver_data;
}

static inline void i2c_set_clientdata(struct i2c_client *dev, void *data)
{
	dev->driver_data = data;
}

/*flags for the client struct: */
#define I2C_CLIENT_PEC	0x04		/* Use Packet Error Checking */
#define I2C_CLIENT_SCCB	0x9000		/* Use Omnivision SCCB protocol */
					/* Must match I2C_M_STOP|IGNORE_NAK */

/*
 * Data for SMBus Messages
 */
#define I2C_SMBUS_BLOCK_MAX	32	/* As specified in SMBus standard */
union i2c_smbus_data {
	__u8 byte;
	__u16 word;
	__u8 block[I2C_SMBUS_BLOCK_MAX + 2]; /* block[0] is used for length */
			       /* and one more for user-space compatibility */
};

/* i2c_smbus_xfer read or write markers */
#define I2C_SMBUS_READ	1
#define I2C_SMBUS_WRITE	0

/* SMBus transaction types (size parameter in the above functions)
   Note: these no longer correspond to the (arbitrary) PIIX4 internal codes! */
#define I2C_SMBUS_QUICK		    0
#define I2C_SMBUS_BYTE		    1
#define I2C_SMBUS_BYTE_DATA	    2
#define I2C_SMBUS_WORD_DATA	    3
#define I2C_SMBUS_I2C_BLOCK_DATA    8

/* This is the very generalized SMBus access routine. You probably do not
   want to use this, though; one of the functions below may be much easier,
   and probably just as fast.
   Note that we use i2c_adapter here, because you do not need a specific
   smbus adapter to call this function. */
extern s32 i2c_smbus_xfer(struct i2c_adapter *adapter, u16 addr,
			  unsigned short flags, char read_write, u8 command,
			  int size, union i2c_smbus_data *data);

/* Now follow the 'nice' access routines. These also document the calling
   conventions of i2c_smbus_xfer. */

extern s32 i2c_smbus_read_byte(const struct i2c_client *client);
extern s32 i2c_smbus_write_byte(const struct i2c_client *client, u8 value);
extern s32 i2c_smbus_read_byte_data(const struct i2c_client *client,
				    u8 command);
extern s32 i2c_smbus_write_byte_data(const struct i2c_client *client,
				     u8 command, u8 value);
extern s32 i2c_smbus_read_word_data(const struct i2c_client *client,
				    u8 command);
extern s32 i2c_smbus_write_word_data(const struct i2c_client *client,
				     u8 command, u16 value);

static inline s32
i2c_smbus_read_word_swapped(const struct i2c_client *client, u8 command)
{
	s32 value = i2c_smbus_read_word_data(client, command);

	return (value < 0) ? value : swab16(value);
}

static inline s32
i2c_smbus_write_word_swapped(const struct i2c_client *client,
			     u8 command, u16 value)
{
	return i2c_smbus_write_word_data(client, command, swab16(value));
}

/* Returns the number of read bytes */
extern s32 i2c_smbus_read_i2c_block_data(const struct i2c_client *client,
					 u8 command, u8 length, u8 *values);
extern s32 i2c_smbus_write_i2c_block_data(const struct i2c_client *client,
					  u8 command, u8 length,
					  const u8 *values);

/**
 * struct i2c_board_info - template for device creation
 *
 * I2C doesn't actually support hardware probing, Drivers commonly
 * need more information than that, such as chip type, configuration,
 * and so on.
 *
 * i2c_board_info is used to build tables of information listing I2C
 * devices that are present. This information is used to grow the
 * driver model tree.  For mainboards this is done statically using
 * i2c_register_board_info(); bus numbers identify adapters that
 * aren't yet available. For add-on boards, i2c_new_device() does this
 * dynamically with the adapter already known.
 */
struct i2c_board_info {
	char		type[I2C_NAME_SIZE];	/**< name of device */
	unsigned short	addr;			/**< stored in i2c_client.addr */
	void		*platform_data;		/**< platform data for device */
	struct device_node *of_node;
};

/**
 * struct i2c_timings - I2C timing information
 * @bus_freq_hz: the bus frequency in Hz
 * @scl_rise_ns: time SCL signal takes to rise in ns; t(r) in the I2C specification
 * @scl_fall_ns: time SCL signal takes to fall in ns; t(f) in the I2C specification
 * @scl_int_delay_ns: time IP core additionally needs to setup SCL in ns
 * @sda_fall_ns: time SDA signal takes to fall in ns; t(f) in the I2C specification
 * @sda_hold_ns: time IP core additionally needs to hold SDA in ns
 * @digital_filter_width_ns: width in ns of spikes on i2c lines that the IP core
 *	digital filter can filter out
 * @analog_filter_cutoff_freq_hz: threshold frequency for the low pass IP core
 *	analog filter
 */
struct i2c_timings {
	u32 bus_freq_hz;
	u32 scl_rise_ns;
	u32 scl_fall_ns;
	u32 scl_int_delay_ns;
	u32 sda_fall_ns;
	u32 sda_hold_ns;
	u32 digital_filter_width_ns;
	u32 analog_filter_cutoff_freq_hz;
};

/**
 * I2C_BOARD_INFO - macro used to list an i2c device and its address
 * @dev_type: identifies the device type
 * @dev_addr: the device's address on the bus.
 *
 * This macro initializes essential fields of a struct i2c_board_info,
 * declaring what has been provided on a particular board. Optional
 * fields (such as associated irq, or device-specific platform_data)
 * are provided using conventional syntax.
 */
#define I2C_BOARD_INFO(dev_type, dev_addr) \
	.type = dev_type, .addr = (dev_addr)

#ifdef CONFIG_I2C
extern int i2c_register_board_info(int busnum, struct i2c_board_info const *info, unsigned n);
#else
static inline int i2c_register_board_info(int busnum,
		struct i2c_board_info const *info, unsigned n)
{
	return 0;
}
#endif
extern int i2c_add_numbered_adapter(struct i2c_adapter *adapter);
struct i2c_adapter *i2c_get_adapter(int busnum);
struct i2c_adapter *of_find_i2c_adapter_by_node(struct device_node *node);
struct i2c_client *of_find_i2c_device_by_node(struct device_node *node);

void i2c_parse_fw_timings(struct device_d *dev, struct i2c_timings *t, bool use_defaults);

extern struct list_head i2c_adapter_list;
#define for_each_i2c_adapter(adap) \
	list_for_each_entry(adap, &i2c_adapter_list, list)

/* For devices that use several addresses, use i2c_new_dummy() to make
 * client handles for the extra addresses.
 */
extern struct i2c_client *
i2c_new_dummy(struct i2c_adapter *adap, u16 address);

/* Return the adapter number for a specific adapter */
static inline int i2c_adapter_id(struct i2c_adapter *adap)
{
	return adap->nr;
}

extern int i2c_transfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num);
extern int i2c_master_send(struct i2c_client *client, const char *buf, int count);
extern int i2c_master_recv(struct i2c_client *client, char *buf, int count);


#define I2C_ADDR_16_BIT	(1 << 31)

extern int i2c_read_reg(struct i2c_client *client, u32 addr, u8 *buf, u16 count);
extern int i2c_write_reg(struct i2c_client *client, u32 addr, const u8 *buf, u16 count);

extern struct bus_type i2c_bus;

static inline int i2c_driver_register(struct driver_d *drv)
{
	drv->bus = &i2c_bus;
	return register_driver(drv);
}

#define coredevice_i2c_driver(drv) \
	register_driver_macro(coredevice, i2c, drv)
#define device_i2c_driver(drv) \
	register_driver_macro(device, i2c, drv)

#endif /* I2C_I2C_H */