if ARCH_IMX
config ARCH_TEXT_BASE
hex
default 0x83f00000 if MACH_EUKREA_CPUIMX25
default 0xa0000000 if MACH_EUKREA_CPUIMX27
default 0x87f00000 if MACH_EUKREA_CPUIMX35
default 0x97f00000 if MACH_EUKREA_CPUIMX51SD
default 0xc0000000 if MACH_IMX21ADS
default 0xa0000000 if MACH_IMX27ADS
default 0x83f00000 if MACH_FREESCALE_MX25_3STACK && FREESCALE_MX25_3STACK_SDRAM_64MB_DDR2
default 0x87f00000 if MACH_FREESCALE_MX25_3STACK && FREESCALE_MX25_3STACK_SDRAM_128MB_MDDR
default 0x87f00000 if MACH_FREESCALE_MX35_3STACK
default 0xa7f00000 if MACH_PCA100
default 0xa0000000 if MACH_PCM038
default 0x87f00000 if MACH_PCM037
default 0x87f00000 if MACH_MX31MOBOARD
default 0x87f00000 if MACH_PCM043
default 0xa7e00000 if MACH_NESO
default 0x97f00000 if MACH_FREESCALE_MX51_PDK
default 0x7ff00000 if MACH_FREESCALE_MX53_LOCO
default 0x7ff00000 if MACH_FREESCALE_MX53_SMD
default 0x7ff00000 if MACH_FREESCALE_MX53_VMX53
default 0x87f00000 if MACH_GUF_CUPID
default 0x93d00000 if MACH_TX25
default 0x7ff00000 if MACH_TQMA53
default 0x97f00000 if MACH_TX51
default 0x4fc00000 if MACH_SABRELITE
default 0x8fe00000 if MACH_TX53
default 0x97f00000 if MACH_EFIKA_MX_SMARTBOOK
default 0x17800000 if MACH_SABRESD
default 0x4fc00000 if MACH_REALQ7
default 0x4fc00000 if MACH_GK802
default 0x87f00000 if MACH_KINDLE3
default 0x2fc00000 if MACH_TQMA6X
default 0x4fc00000 if MACH_DFI_FS700_M60
default 0x4fc00000 if MACH_UDOO
default 0x4fc00000 if MACH_VARISCITE_MX6
default 0x4fc00000 if MACH_PHYTEC_SOM_IMX6
default 0x9fc00000 if MACH_WARP7
config ARCH_IMX_IMXIMAGE
bool
default y
help
if enabled the imx-image tool is compiled
config ARCH_IMX_IMXIMAGE_SSL_SUPPORT
bool
help
This enables SSL support for the imx-image tool. This is required
for created images for HABv3. This adds openssl to the build dependencies
config ARCH_IMX_EXTERNAL_BOOT_NAND
bool
depends on ARCH_IMX25 || ARCH_IMX27 || ARCH_IMX31 || ARCH_IMX35
prompt "Support Starting barebox from NAND in external bootmode"
config BAREBOX_UPDATE_IMX_EXTERNAL_NAND
bool
depends on ARCH_IMX_EXTERNAL_BOOT_NAND
depends on BAREBOX_UPDATE
depends on MTD
depends on MTD_WRITE
default y
config RESET_IMX_SRC
def_bool y
depends on ARCH_IMX6 || ARCH_IMX50 || ARCH_IMX51 || ARCH_IMX53
#
# PMIC configuration found on i.MX51 Babbadge board
#
config MACH_FREESCALE_MX51_PDK_POWER
bool
select SPI
select DRIVER_SPI_IMX
select MFD_MC13XXX
comment "Freescale i.MX System-on-Chip"
config ARCH_IMX1
bool
select CPU_ARM920T
select ARCH_HAS_IMX_GPT
select PINCTRL_IMX_IOMUX_V1
config ARCH_IMX21
bool
select CPU_ARM926T
select ARCH_HAS_IMX_GPT
select PINCTRL_IMX_IOMUX_V1
config ARCH_IMX25
bool
select CPU_ARM926T
select ARCH_HAS_FEC_IMX
select ARCH_HAS_IMX_GPT
select PINCTRL_IMX_IOMUX_V3
config ARCH_IMX27
bool
select CPU_ARM926T
select ARCH_HAS_FEC_IMX
select ARCH_HAS_IMX_GPT
select PINCTRL_IMX_IOMUX_V1
config ARCH_IMX31
select CPU_V6
bool
select ARCH_HAS_IMX_GPT
select PINCTRL_IMX_IOMUX_V2
config ARCH_IMX35
bool
select CPU_V6
select ARCH_HAS_FEC_IMX
select ARCH_HAS_IMX_GPT
select PINCTRL_IMX_IOMUX_V3
config ARCH_IMX50
bool
select CPU_V7
select ARCH_HAS_FEC_IMX
select ARCH_HAS_IMX_GPT
select PINCTRL_IMX_IOMUX_V3
config ARCH_IMX51
bool
select CPU_V7
select ARCH_HAS_FEC_IMX
select ARCH_HAS_IMX_GPT
select PINCTRL_IMX_IOMUX_V3
config ARCH_IMX53
bool
select CPU_V7
select ARCH_HAS_FEC_IMX
select ARCH_HAS_IMX_GPT
select PINCTRL_IMX_IOMUX_V3
config ARCH_IMX6
bool
select ARCH_HAS_L2X0
select ARCH_HAS_FEC_IMX
select ARCH_HAS_IMX_GPT
select CPU_V7
select PINCTRL_IMX_IOMUX_V3
select OFTREE
select COMMON_CLK_OF_PROVIDER
select HW_HAS_PCI
config ARCH_IMX6SL
bool
select ARCH_IMX6
config ARCH_IMX6SX
bool
select ARCH_IMX6
select OFTREE
select COMMON_CLK_OF_PROVIDER
config ARCH_IMX6UL
bool
select ARCH_IMX6
config ARCH_IMX7
bool
select CPU_V7
select PINCTRL_IMX_IOMUX_V3
select OFTREE
select COMMON_CLK_OF_PROVIDER
select ARCH_HAS_FEC_IMX
select ARCH_HAS_IMX_GPT
select HW_HAS_PCI
config ARCH_IMX8M
bool
select CPU_V8
select PINCTRL_IMX_IOMUX_V3
select OFTREE
select SYS_SUPPORTS_64BIT_KERNEL
select COMMON_CLK_OF_PROVIDER
select ARCH_HAS_FEC_IMX
select HW_HAS_PCI
select IMX8M_DRAM
select PBL_VERIFY_PIGGY if HABV4
config ARCH_IMX8MM
select ARCH_IMX8M
bool
config ARCH_IMX8MP
select ARCH_IMX8M
bool
config ARCH_IMX8MQ
select ARCH_IMX8M
bool
config ARCH_VF610
bool
select ARCH_HAS_L2X0
select ARCH_HAS_FEC_IMX
select CPU_V7
select PINCTRL
select OFDEVICE
select OFTREE
select COMMON_CLK
select COMMON_CLK_OF_PROVIDER
select NVMEM
select IMX_OCOTP # Needed for clock adjustement
select CLOCKSOURCE_ARM_GLOBAL_TIMER
config IMX_MULTI_BOARDS
bool "Allow multiple boards to be selected"
select HAVE_PBL_MULTI_IMAGES
if IMX_MULTI_BOARDS
config MACH_SCB9328
bool "Synertronixx scb9328"
select ARCH_IMX1
select HAS_DM9000
help
Say Y here if you are using the Synertronixx scb9328 board
config MACH_TX25
bool "Ka-Ro TX25"
select ARCH_IMX25
select ARCH_IMX_EXTERNAL_BOOT_NAND
help
Say Y here if you are using the Ka-Ro tx25 board
config MACH_PCA100
bool "phyCard-i.MX27"
select ARCH_IMX27
select ARCH_IMX_EXTERNAL_BOOT_NAND
help
Say Y here if you are using Phytec's phyCard-i.MX27 (pca100) equipped
with a Freescale i.MX27 Processor
config MACH_PCM038
bool "phyCORE-i.MX27"
select ARCH_IMX27
select SPI
select DRIVER_SPI_IMX
select MFD_MC13XXX
select ARCH_IMX_EXTERNAL_BOOT_NAND
help
Say Y here if you are using Phytec's phyCORE-i.MX27 (pcm038) equipped
with a Freescale i.MX27 Processor
config MACH_KINDLE_MX50
bool "i.MX50 based Amazon Kindle 4 and 5"
select ARCH_IMX50
select SPI
select DRIVER_SPI_IMX
select I2C
select I2C_IMX
select MFD_MC13XXX
select ARM_BOARD_APPEND_ATAG
select ARM_LINUX
select OFTREE
help
Say Y here if you are using the fourth or fifth generation Amazon
Kindle Model No. D01100 (Kindle Wi-Fi), D01200 (Kindle Touch) or
EY21 (Kindle Paperwhite).
config MACH_CCMX51
bool "ConnectCore i.MX51"
select ARCH_IMX51
select IMX_IIM
select SPI
select DRIVER_SPI_IMX
select MFD_MC13XXX
select RELOCATABLE
help
Say Y here if you are using Digi ConnectCore (W)i-i.MX51
equipped with a Freescale i.MX51 Processor
config MACH_EFIKA_MX_SMARTBOOK
bool "Efika MX smartbook"
select ARCH_IMX51
select SPI
select DRIVER_SPI_IMX
select MFD_MC13XXX
help
Choose this to compile barebox for the Efika MX Smartbook
config MACH_EMBEDSKY_E9
bool "Embedsky E9 Mini-PC"
select ARCH_IMX6
help
Choose this to compile barebox for the Embedsky E9 Mini PC
config MACH_FREESCALE_MX51_PDK
bool "Freescale i.MX51 PDK"
select ARCH_IMX51
select MACH_FREESCALE_MX51_PDK_POWER
config MACH_CCMX53
bool "Digi ConnectCore i.MX53"
select ARCH_IMX53
select I2C
help
Say Y here if you are using the Digi ConnectCore ccxmx53
series SoM
config MACH_FREESCALE_MX53_LOCO
bool "Freescale i.MX53 LOCO"
select ARCH_IMX53
select I2C
select I2C_IMX
select MFD_MC13XXX
config MACH_GUF_VINCELL
bool "Garz-Fricke Vincell"
select ARCH_IMX53
config MACH_TQMA53
bool "TQ i.MX53 TQMa53"
select ARCH_IMX53
config MACH_FREESCALE_MX53_VMX53
bool "Voipac i.MX53"
select ARCH_IMX53
help
Say Y here if you are using the Voipac Technologies X53-DMM-668
module equipped with a Freescale i.MX53 Processor
config MACH_TX53
bool "Ka-Ro TX53"
select ARCH_IMX53
help
Say Y here if you are using the Ka-Ro tx53 board
config MACH_PHYTEC_SOM_IMX6
bool "Phytec phyCARD-i.MX6 and phyFLEX-i.MX6"
select ARCH_IMX6
select ARCH_IMX6UL
config MACH_PROTONIC_IMX6
bool "Protonic-Holland i.MX6 based boards"
select ARCH_IMX6
select ARCH_IMX6UL
select ARM_USE_COMPRESSED_DTB
config MACH_KONTRON_SAMX6I
bool "Kontron sAMX6i"
select ARCH_IMX6
config MACH_DFI_FS700_M60
bool "DFI i.MX6 FS700 M60 Q7 Board"
select ARCH_IMX6
config MACH_GUF_SANTARO
bool "Garz+Fricke Santaro Board"
select ARCH_IMX6
select I2C
select I2C_IMX
config MACH_REALQ7
bool "DataModul i.MX6Q Real Qseven Board"
select ARCH_IMX6
config MACH_GK802
bool "Zealz GK802 Mini PC"
select ARCH_IMX6
config MACH_ELTEC_HIPERCAM
bool "ELTEC HiPerCam"
select ARCH_IMX6
config MACH_TQMA6X
bool "TQ tqma6x on mba6x"
select ARCH_IMX6
config MACH_TX6X
bool "Karo TX6x"
select ARCH_IMX6
select I2C
select I2C_IMX
config MACH_SABRELITE
bool "Freescale i.MX6 Sabre Lite"
select ARCH_IMX6
config MACH_SABRESD
bool "Freescale i.MX6 SabreSD"
select ARCH_IMX6
config MACH_FREESCALE_IMX6SX_SABRESDB
bool "Freescale i.MX6sx SabreSDB"
select ARCH_IMX6SX
select I2C
select I2C_IMX
config MACH_NITROGEN6
bool "BoundaryDevices Nitrogen6 boards"
select ARCH_IMX6
config MACH_SOLIDRUN_MICROSOM
bool "SolidRun MicroSOM based devices"
select ARCH_IMX6
config MACH_TECHNEXION_PICO_HOBBIT
bool "Technexion Pico Hobbit"
select ARCH_IMX6
select ARCH_IMX6UL
select ARM_USE_COMPRESSED_DTB
config MACH_TECHNEXION_WANDBOARD
bool "Technexion Wandboard"
select ARCH_IMX6
select ARM_USE_COMPRESSED_DTB
select MCI_IMX_ESDHC_PBL
config MACH_EMBEST_MARSBOARD
bool "Embest MarSboard"
select ARCH_IMX6
select ARM_USE_COMPRESSED_DTB
config MACH_EMBEST_RIOTBOARD
bool "Embest RIoTboard"
select ARCH_IMX6
config MACH_UDOO
bool "Freescale i.MX6 UDOO Board"
select ARCH_IMX6
config MACH_UDOO_NEO
bool "i.MX6 UDOO Neo Board (full variant)"
select ARCH_IMX6SX
config MACH_VARISCITE_MX6
bool "Variscite i.MX6 Quad SOM"
select ARCH_IMX6
select I2C
select I2C_IMX
config MACH_GW_VENTANA
bool "Gateworks Ventana SBC"
select ARCH_IMX6
select I2C
select I2C_IMX
config MACH_CM_FX6
bool "CM FX6"
select ARCH_IMX6
config MACH_ADVANTECH_ROM_742X
bool "Advantech ROM 742X"
select ARCH_IMX6
select ARM_USE_COMPRESSED_DTB
config MACH_WARP7
bool "NXP i.MX7: element 14 WaRP7 Board"
select ARCH_IMX7
config MACH_VF610_TWR
bool "Freescale VF610 Tower Board"
select ARCH_VF610
config MACH_ZII_COMMON
bool
config MACH_ZII_RDU1
bool "ZII i.MX51 RDU1"
select ARCH_IMX51
select MACH_FREESCALE_MX51_PDK_POWER
select CRC8
select MACH_ZII_COMMON
select ARM_USE_COMPRESSED_DTB
config MACH_ZII_RDU2
bool "ZII i.MX6Q(+) RDU2"
select ARCH_IMX6
select MCI_IMX_ESDHC_PBL
select MACH_ZII_COMMON
select ARM_USE_COMPRESSED_DTB
config MACH_ZII_IMX8MQ_DEV
bool "ZII i.MX8MQ based devices"
select ARCH_IMX8MQ
select FIRMWARE_IMX_LPDDR4_PMU_TRAIN
select FIRMWARE_IMX8MQ_ATF
select ARM_SMCCC
select MCI_IMX_ESDHC_PBL
select MACH_ZII_COMMON
select ARM_USE_COMPRESSED_DTB
config MACH_ZII_VF610_DEV
bool "ZII VF610 Dev Family"
select ARCH_VF610
select CLKDEV_LOOKUP
select MACH_ZII_COMMON
select ARM_USE_COMPRESSED_DTB
config MACH_ZII_IMX7D_DEV
bool "ZII i.MX7D based devices"
select ARCH_IMX7
select ARM_USE_COMPRESSED_DTB
config MACH_PHYTEC_PHYCORE_IMX7
bool "Phytec phyCORE i.MX7"
select ARCH_IMX7
config MACH_FREESCALE_MX7_SABRESD
bool "NXP i.MX7 SabreSD Board"
select ARCH_IMX7
# Nedded to de-assert reset on Ethernet PHY
select DRIVER_SPI_GPIO if DRIVER_NET_FEC_IMX
select GPIO_74164 if DRIVER_NET_FEC_IMX
help
Support for NXP i.MX7 SabreSD board - one of the official
i.MX7 evaluation boards from NXP.
https://goo.gl/6EKGdk
config MACH_NXP_IMX6ULL_EVK
bool "NXP i.MX6ull EVK Board"
select ARCH_IMX6UL
config MACH_NXP_IMX8MM_EVK
bool "NXP i.MX8MM EVK Board"
select ARCH_IMX8MM
select FIRMWARE_IMX8MM_ATF
select ARM_SMCCC
select MCI_IMX_ESDHC_PBL
select IMX8M_DRAM
select I2C_IMX_EARLY
select USB_GADGET_DRIVER_ARC_PBL
config MACH_NXP_IMX8MQ_EVK
bool "NXP i.MX8MQ EVK Board"
select ARCH_IMX8MQ
select FIRMWARE_IMX_LPDDR4_PMU_TRAIN
select FIRMWARE_IMX8MQ_ATF
select ARM_SMCCC
select MCI_IMX_ESDHC_PBL
config MACH_PHYTEC_SOM_IMX8MQ
bool "Phytec i.MX8M SOM"
select ARCH_IMX8MQ
select FIRMWARE_IMX_LPDDR4_PMU_TRAIN
select FIRMWARE_IMX8MQ_ATF
select ARM_SMCCC
select MCI_IMX_ESDHC_PBL
config MACH_GRINN_LITEBOARD
bool "Grinn liteboard"
select ARCH_IMX6UL
config MACH_DIGI_CCIMX6ULSBCPRO
bool "Digi Internal CC-IMX6UL SBC Pro"
select ARCH_IMX6
select ARCH_IMX6UL
select ARM_USE_COMPRESSED_DTB
endif
# ----------------------------------------------------------
choice
prompt "Select Board"
depends on !IMX_MULTI_BOARDS
# ----------------------------------------------------------
comment "i.MX21 Boards"
config MACH_IMX21ADS
bool "Freescale i.MX21ADS"
select ARCH_IMX21
select HAS_CS8900
help
Say Y here if you are using the Freescale i.MX21ads board equipped
with a Freescale i.MX21 Processor
# ----------------------------------------------------------
comment "i.MX25 Boards"
config MACH_EUKREA_CPUIMX25
bool "Eukrea CPUIMX25"
select ARCH_IMX25
help
Say Y here if you are using the Eukrea Electromatique's CPUIMX25
equipped with a Freescale i.MX25 Processor
config MACH_FREESCALE_MX25_3STACK
bool "Freescale MX25 3stack"
select ARCH_IMX25
select I2C
select MFD_MC34704
help
Say Y here if you are using the Freescale MX25 3stack board equipped
with a Freescale i.MX25 Processor
# ----------------------------------------------------------
comment "i.MX27 Boards"
config MACH_EUKREA_CPUIMX27
bool "EUKREA CPUIMX27"
select ARCH_IMX27
help
Say Y here if you are using Eukrea's CPUIMX27 equipped
with a Freescale i.MX27 Processor
config MACH_IMX27ADS
bool "Freescale i.MX27ADS"
select ARCH_IMX27
help
Say Y here if you are using the Freescale i.MX27ads board equipped
with a Freescale i.MX27 Processor
config MACH_NESO
bool "Garz+Fricke Neso"
select ARCH_IMX27
help
Say Y here if you are using the Garz+Fricke Neso board equipped
with a Freescale i.MX27 Processor
# ----------------------------------------------------------
comment "i.MX31 Boards"
config MACH_PCM037
bool "phyCORE-i.MX31"
select ARCH_IMX31
select USB_ULPI if USB
select ARCH_HAS_L2X0
help
Say Y here if you are using Phytec's phyCORE-i.MX31 (pcm037) equipped
with a Freescale i.MX31 Processor
config MACH_MX31MOBOARD
bool "mx31moboard-i.MX31"
select ARCH_IMX31
select USB_ULPI if USB
select ARCH_HAS_L2X0
help
Say Y here if you are using EPFL mx31moboard board equipped
with a Freescale i.MX31 Processor
# ----------------------------------------------------------
comment "i.MX35 Boards"
config MACH_EUKREA_CPUIMX35
bool "EUKREA CPUIMX35"
select ARCH_IMX35
select ARCH_HAS_L2X0
help
Say Y here if you are using Eukrea's CPUIMX35 equipped
with a Freescale i.MX35 Processor
config MACH_FREESCALE_MX35_3STACK
bool "Freescale MX35 3stack"
select ARCH_IMX35
select I2C
select I2C_IMX
select MFD_MC13XXX
select MFD_MC9SDZ60
help
Say Y here if you are using the Freescale MX35 3stack board equipped
with a Freescale i.MX35 Processor
config MACH_PCM043
bool "phyCORE-i.MX35"
select ARCH_IMX35
select ARCH_HAS_L2X0
help
Say Y here if you are using Phytec's phyCORE-i.MX35 (pcm043) equipped
with a Freescale i.MX35 Processor
config MACH_GUF_CUPID
bool "Garz+Fricke Cupid"
select ARCH_IMX35
select ARCH_HAS_L2X0
help
Say Y here if you are using the Garz+Fricke Neso board equipped
with a Freescale i.MX35 Processor
config MACH_KINDLE3
bool "Amazon Kindle3"
select ARCH_IMX35
select ARCH_HAS_L2X0
help
Say Y here if you are using the Amazon Model No. D00901 Kindle
# ----------------------------------------------------------
comment "i.MX51 Boards"
config MACH_EUKREA_CPUIMX51SD
bool "EUKREA CPUIMX51"
select ARCH_IMX51
help
Say Y here if you are using Eukrea's CPUIMX51 equipped
with a Freescale i.MX51 Processor
config MACH_TX51
bool "Ka-Ro TX51"
select ARCH_IMX51
help
Say Y here if you are using the Ka-Ro tx51 board
# ----------------------------------------------------------
comment "i.MX53 Boards"
config MACH_FREESCALE_MX53_SMD
bool "Freescale i.MX53 SMD"
select ARCH_IMX53
endchoice
# ----------------------------------------------------------
menu "Board specific settings"
if MACH_PCM037
choice
prompt "SDRAM Bank0"
config PCM037_SDRAM_BANK0_128MB
bool "128MB"
config PCM037_SDRAM_BANK0_256MB
bool "256MB"
endchoice
choice
prompt "SDRAM Bank1"
config PCM037_SDRAM_BANK1_NONE
bool "none"
config PCM037_SDRAM_BANK1_128MB
bool "128MB"
config PCM037_SDRAM_BANK1_256MB
bool "256MB"
endchoice
endif
if MACH_EUKREA_CPUIMX27
choice
prompt "SDRAM Size"
config EUKREA_CPUIMX27_SDRAM_128MB
bool "128 MB"
config EUKREA_CPUIMX27_SDRAM_256MB
bool "256 MB"
endchoice
choice
prompt "NOR Flash Size"
config EUKREA_CPUIMX27_NOR_32MB
bool "<= 32 MB"
config EUKREA_CPUIMX27_NOR_64MB
bool "> 32 MB"
endchoice
choice
prompt "Quad UART Port"
depends on DRIVER_SERIAL_NS16550
config EUKREA_CPUIMX27_QUART1
bool "Q1"
config EUKREA_CPUIMX27_QUART2
bool "Q2"
config EUKREA_CPUIMX27_QUART3
bool "Q3"
config EUKREA_CPUIMX27_QUART4
bool "Q4"
endchoice
endif
if MACH_FREESCALE_MX25_3STACK
choice
prompt "SDRAM Type"
config FREESCALE_MX25_3STACK_SDRAM_64MB_DDR2
bool "64 MB (DDR2)"
config FREESCALE_MX25_3STACK_SDRAM_128MB_MDDR
bool "128 MB (mDDR)"
endchoice
endif
endmenu
menu "i.MX specific settings"
config IMX_IIM
tristate "IIM fusebox device"
depends on !ARCH_IMX21
help
Device driver for the IC Identification Module (IIM) fusebox. Use the
regular md/mw commands to program and read the fusebox.
Fuses are grouped in "rows", 8 bits per row. When using md/mw commands,
employ the -b switch and consider the region to be specifying the "Fuse
Row Index" rather than "Fuse Row Offset" (which is FRI * 4). You should
consult the documentation for your chip for more elaborate description,
including the eFuse map, e.g. see AN3682 for i.MX25.
config IMX_IIM_FUSE_BLOW
bool "IIM fuses blow support"
depends on IMX_IIM
help
Enable this option to add permanent programming of the fusebox, using
fuses blowing.
Warning: blown fuses can not be unblown. Using this option may damage
your CPU, or make it unbootalbe. Use with care.
Before being actually able to blow the fuses, you need to explicitely
enable it:
imx_iim0.permanent_write_enable=1
config HAB
bool
config HABV4
tristate "HABv4 support"
select HAB
select NVMEM
select IMX_OCOTP
depends on ARCH_IMX6 || ARCH_IMX8MQ
depends on OFDEVICE
help
High Assurance Boot, as found on i.MX28/i.MX6/i.MX8MQ.
config HAB_CERTS_ENV
depends on HAB
bool "Specify certificates in environment"
help
If this option is enabled the pathes to the HAB certificates are
taken from environment variables which allows for better integration
with build systems. With this option disabled the pathes can be
specified below.
The environment variables have the same name as the corresponding
Kconfig variables. For HABv3 these are:
CONFIG_HABV3_SRK_PEM
CONFIG_HABV3_CSF_CRT_DER
CONFIG_HABV3_IMG_CRT_DER
For HABv4:
CONFIG_HABV4_TABLE_BIN
CONFIG_HABV4_CSF_CRT_PEM
CONFIG_HABV4_IMG_CRT_PEM
config HABV4_SRK_INDEX
depends on HABV4
int "SRK index"
default 0
help
Select the Super Root Key used in the Command Sequence File to sign
the CSF binary. This should only be changed if a previous key was
revoked and another key needs to be used. For HABV4 the Index is in
the range from 0 to 3.
if HABV4 && !HAB_CERTS_ENV
config HABV4_TABLE_BIN
string "Path to SRK table"
default "../crts/SRK_1_2_3_4_table.bin"
help
Path to the Super Root Key (SRK) table, produced by the
Freescale Code Signing Tool (cst).
This file will be inserted into the Command Sequence File
(CSF) when using the CSF template that comes with barebox.
config HABV4_CSF_CRT_PEM
string "Path to CSF certificate"
default "../crts/CSF1_1_sha256_4096_65537_v3_usr_crt.pem"
help
Path to the Command Sequence File (CSF) certificate, produced by the
Freescale Public Key Infrastructure (PKI) script.
This file will be inserted into the Command Sequence File
(CSF) when using the CSF template that comes with barebox.
config HABV4_IMG_CRT_PEM
string "Path to IMG certificate"
default "../crts/IMG1_1_sha256_4096_65537_v3_usr_crt.pem"
help
Path to the Image certificate, produced by the Freescale
Public Key Infrastructure (PKI) script.
This file will be inserted into the Command Sequence File
(CSF) when using the CSF template that comes with barebox.
endif
if HABV4
config HABV4_IMAGE_SIGNED
bool "build signed images"
help
enable the creation of a signed image, if the habv4-imx6-gencsf.h
included in the flash-header and the NXP cst Tool is available
config HABV4_IMAGE_SIGNED_USB
bool "build signed USB images"
help
enable the creation of a usb signed image, if the habv4-imx6-gencsf.h
included in the flash-header and the NXP cst Tool is available
config HABV4_IMAGE_SIGNED_ENCRYPTED
bool "build signed encrypted images"
help
enable the creation of the encrypted image, if the habv4-imx6-gencsf.h
included in the flash-header and the NXP cst Tool is available
endif
config HABV3
tristate "HABv3 support"
select HAB
select IMX_IIM
select ARCH_IMX_IMXIMAGE_SSL_SUPPORT
depends on ARCH_IMX25
help
High Assurance Boot, as found on i.MX25.
if HABV3 && !HAB_CERTS_ENV
config HABV3_SRK_PEM
string "Path to SRK Certificate (PEM)"
default "../crts/SRK1_sha256_2048_65537_v3_ca_x509_crt.pem"
config HABV3_CSF_CRT_DER
string "Path to CSF certificate"
default "../crts/CSF1_1_sha256_2048_65537_v3_ca_crt.der"
config HABV3_IMG_CRT_DER
string "Path to IMG certificate"
default "../crts/IMG1_1_sha256_2048_65537_v3_usr_crt.der"
endif
endmenu
endif
