/*
* (C) Copyright 2001
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* configuration options, board specific, for Siemens Card Controller Module
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#undef CCM_80MHz /* define for 80 MHz CPU only */
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC860 1 /* This is a MPC860 CPU ... */
#define CONFIG_CCM 1 /* on a Card Controller Module */
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
#undef CONFIG_8xx_CONS_SMC2
#undef CONFIG_8xx_CONS_NONE
/* ENVIRONMENT */
#define CONFIG_BAUDRATE 19200 /* console baudrate in bps */
#define CONFIG_BOOTDELAY 2 /* autoboot after 2 seconds */
#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
#define CONFIG_IPADDR 192.168.0.42
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_GATEWAYIP 0.0.0.0
#define CONFIG_SERVERIP 192.168.0.254
#define CONFIG_HOSTNAME CCM
#define CONFIG_LOADADDR 40180000
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND "setenv bootargs " \
"mem=$(mem) " \
"root=/dev/ram rw ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off " \
"wt_8xx=timeout:3600; " \
"bootm"
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#define CONFIG_WATCHDOG 1 /* watchdog enabled */
#undef CONFIG_STATUS_LED /* Status LED disabled */
#define CONFIG_PRAM 512 /* reserve 512kB "protected RAM"*/
#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
#define CONFIG_SPI /* enable SPI driver */
#define CONFIG_SPI_X /* 16 bit EEPROM addressing */
/* ----------------------------------------------------------------
* Offset to initial SPI buffers in DPRAM (used if the environment
* is in the SPI EEPROM): We need a 520 byte scratch DPRAM area to
* use at an early stage. It is used between the two initialization
* calls (spi_init_f() and spi_init_r()). The value 0xB00 makes it
* far enough from the start of the data area (as well as from the
* stack pointer).
* ---------------------------------------------------------------- */
#define CFG_SPI_INIT_OFFSET 0xB00
#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* 32-byte page size */
#define CONFIG_MAC_PARTITION /* nod used yet */
#define CONFIG_DOS_PARTITION
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_DHCP | \
CFG_CMD_DATE | \
CFG_CMD_EEPROM | \
CFG_CMD_BSP )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
/*----------------------------------------------------------------------*/
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */
#define CFG_LOAD_ADDR 0x00100000 /* default load address */
/* Ethernet hardware configuration done using port pins */
#define CFG_PA_ETH_RESET 0x0200 /* PA 6 */
#define CFG_PA_ETH_MDDIS 0x4000 /* PA 1 */
#define CFG_PB_ETH_POWERDOWN 0x00000800 /* PB 20 */
#define CFG_PB_ETH_CFG1 0x00000400 /* PB 21 */
#define CFG_PB_ETH_CFG2 0x00000200 /* PB 22 */
#define CFG_PB_ETH_CFG3 0x00000100 /* PB 23 */
/* Ethernet settings:
* MDIO not disabled, autonegotiation, 10/100Mbps, half/full duplex
*/
#define CFG_ETH_MDDIS_VALUE 0
#define CFG_ETH_CFG1_VALUE 1
#define CFG_ETH_CFG2_VALUE 1
#define CFG_ETH_CFG3_VALUE 1
/* PUMA configuration */
#define CFG_PC_PUMA_PROG 0x0200 /* PC 6 */
#define CFG_PC_PUMA_DONE 0x0008 /* PC 12 */
#define CFG_PC_PUMA_INIT 0x0004 /* PC 13 */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
#define CFG_IMMR 0xF0000000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_INIT_RAM_ADDR CFG_IMMR
#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Address accessed to reset the board - must not be mapped/assigned
*/
#define CFG_RESET_ADDRESS 0xFEFFFFFF
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0x40000000
#if defined(DEBUG)
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#else
#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
#endif
#define CFG_MONITOR_BASE CFG_FLASH_BASE
#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#if 1
/* Start port with environment in flash; switch to SPI EEPROM later */
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SIZE)
#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
#else
/* Final version: environment in EEPROM */
#define CFG_ENV_IS_IN_EEPROM 1
#define CFG_ENV_OFFSET 2048
#define CFG_ENV_SIZE 2048
#endif
/*-----------------------------------------------------------------------
* Hardware Information Block
*/
#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */
#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
* SYPCR can only be written once after reset!
*-----------------------------------------------------------------------
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
#if defined(CONFIG_WATCHDOG)
#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
#else
#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWP)
#endif
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 11-6
*-----------------------------------------------------------------------
* we must activate GPL5 in the SIUMCR for CAN
*/
#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control 11-26
*-----------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
*/
#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
/*-----------------------------------------------------------------------
* RTCSC - Real-Time Clock Status and Control Register 11-27
*-----------------------------------------------------------------------
*/
#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 11-31
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
*/
#define CFG_PISCR (PISCR_PS | PISCR_PITF)
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
*-----------------------------------------------------------------------
* Reset PLL lock status sticky bit, timer expired status bit and timer
* interrupt status bit
*
* If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
*/
#ifdef CCM_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */
#define CFG_PLPRCR \
( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
#else /* up to 50 MHz we use a 1:1 clock */
#define CFG_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
#endif /* CCM_80MHz */
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
*-----------------------------------------------------------------------
* Set clock output, timebase and RTC source and divider,
* power management and some other internal clocks
*/
#define SCCR_MASK SCCR_EBDF11
#ifdef CCM_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */
#define CFG_SCCR (/* SCCR_TBS | */ \
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
SCCR_DFALCD00)
#else /* up to 50 MHz we use a 1:1 clock */
#define CFG_SCCR (SCCR_TBS | \
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
SCCR_DFALCD00)
#endif /* CCM_80MHz */
/*-----------------------------------------------------------------------
*
* Interrupt Levels
*-----------------------------------------------------------------------
*/
#define CFG_CPM_INTERRUPT 13 /* SIU_LEVEL6 */
/*-----------------------------------------------------------------------
*
*-----------------------------------------------------------------------
*
*/
#define CFG_DER 0
/*
* Init Memory Controller:
*
* BR0/1 and OR0/1 (FLASH)
*/
#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
/* used to re-map FLASH both when starting from SRAM or FLASH:
* restrict access enough to keep SRAM working (if any)
* but not too much to meddle with FLASH accesses
*/
#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */
#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */
#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \
OR_SCY_5_CLK | OR_EHTR)
#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
#define CFG_OR1_REMAP CFG_OR0_REMAP
#define CFG_OR1_PRELIM CFG_OR0_PRELIM
#define CFG_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
/*
* BR2 and OR2 (SDRAM)
*
*/
#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
#define CFG_OR_TIMING_SDRAM 0x00000A00
#define CFG_OR2_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
/*
* BR3 and OR3 (CAN Controller)
*/
#define CFG_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
#define CFG_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
#define CFG_OR3_CAN (CFG_CAN_OR_AM | OR_G5LA | OR_BI)
#define CFG_BR3_CAN ((CFG_CAN_BASE & BR_BA_MSK) | \
BR_PS_8 | BR_MS_UPMB | BR_V )
/*
* BR4/OR4: PUMA Config
*
* Memory controller will be used in 2 modes:
*
* - "read" mode:
* BR4: 0x10100801 OR4: 0xffff8520
* - "load" mode (chip select on UPM B):
* BR4: 0x101004c1 OR4: 0xffff8600
*
* Default initialization is in "read" mode
*/
#define PUMA_CONF_BASE 0x10100000 /* PUMA Config */
#define PUMA_CONF_OR_AM 0xFFFF8000 /* 32 kB */
#define PUMA_CONF_LOAD_TIMING (OR_ACS_DIV2 | OR_SCY_2_CLK)
#define PUMA_CONF_READ_TIMING (OR_G5LA | OR_BI | OR_SCY_2_CLK)
#define PUMA_CONF_BR_LOAD ((PUMA_CONF_BASE & BR_BA_MSK) | \
BR_PS_8 | BR_MS_UPMB | BR_V)
#define PUMA_CONF_OR_LOAD (PUMA_CONF_OR_AM | PUMA_CONF_LOAD_TIMING)
#define PUMA_CONF_BR_READ ((PUMA_CONF_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
#define PUMA_CONF_OR_READ (PUMA_CONF_OR_AM | PUMA_CONF_READ_TIMING)
#define CFG_BR4_PRELIM PUMA_CONF_BR_READ
#define CFG_OR4_PRELIM PUMA_CONF_OR_READ
/*
* BR5/OR5: PUMA: SMA Bus 8 Bit
* BR5: 0x10200401 OR5: 0xffe0010a
*/
#define PUMA_SMA8_BASE 0x10200000 /* PUMA SMA Bus 8 Bit */
#define PUMA_SMA8_OR_AM 0xFFE00000 /* 2 MB */
#define PUMA_SMA8_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR)
#define CFG_BR5_PRELIM ((PUMA_SMA8_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)
#define CFG_OR5_PRELIM (PUMA_SMA8_OR_AM | PUMA_SMA8_TIMING | OR_SETA)
/*
* BR6/OR6: PUMA: SMA Bus 16 Bit
* BR6: 0x10600801 OR6: 0xffe0010a
*/
#define PUMA_SMA16_BASE 0x10600000 /* PUMA SMA Bus 16 Bit */
#define PUMA_SMA16_OR_AM 0xFFE00000 /* 2 MB */
#define PUMA_SMA16_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR)
#define CFG_BR6_PRELIM ((PUMA_SMA16_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
#define CFG_OR6_PRELIM (PUMA_SMA16_OR_AM | PUMA_SMA16_TIMING | OR_SETA)
/*
* BR7/OR7: PUMA: external Flash
* BR7: 0x10a00801 OR7: 0xfe00010a
*/
#define PUMA_FLASH_BASE 0x10A00000 /* PUMA external Flash */
#define PUMA_FLASH_OR_AM 0xFE000000 /* 32 MB */
#define PUMA_FLASH_TIMING (OR_BI | OR_SCY_0_CLK | OR_EHTR)
#define CFG_BR7_PRELIM ((PUMA_FLASH_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
#define CFG_OR7_PRELIM (PUMA_FLASH_OR_AM | PUMA_FLASH_TIMING | OR_SETA)
/*
* Memory Periodic Timer Prescaler
*/
/* periodic timer for refresh */
#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */
/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
/*
* MAMR settings for SDRAM
*/
/* 8 column SDRAM */
#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
/* 9 column SDRAM */
#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#endif /* __CONFIG_H */
